Epson S5U13742P00C100 Bedienungsanleitung

Rev. 1.1

S1D13742 Mobile Graphics Engine

S5U13742P00C100 Evaluation

Board User Manual

Document Number: X63A-G-002-01.1

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written permission

of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does

not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application

or use in any product or circuit and, further, there is no representation that this material is applicable to products

requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights

is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance

with this material will be free from any patent or copyright infringement of a third party. When exporting the

products or technology described in this material, you should comply with the applicable export control laws and

regulations and follow the procedures required by such laws and regulations. You are requested not to use, to resell,

to export and/or to otherwise dispose of the products (and any technical information furnished, if any) for the devel-

opment and/or manufacture of weapon of mass destruction or for other military purposes.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective

companies.

Evaluation Board/Kit and Development Tool Important Notice

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration, or develop-

ment purposes only. Do not use it for other purposes. It is not intended to meet the requirements of design for finished

products.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a consumer product.

The user should use it properly and in a safe manner. Seiko Epson does not assume any responsibility or liability of any

kind of damage and/or fire caused by the use of it. The user should cease to use it when any abnormal issue occurs even

during proper and safe use.

3. The part used for this evaluation board/kit or development tool may be changed without any notice.

2Seiko Epson Corporation S5U13742P00C100 Evaluation Board

Rev. 1.1

S5U13742P00C100 Evaluation Board Seiko Epson Corporation 3

Rev. 1.1

Table of Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Configuration DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.1 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.2 Voltage Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1.3 S1D13742 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.3 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.4 Power Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.5 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.5.1 Direct Host Bus Interface Support . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.5.2 Connecting to the Epson S5U13U00P00C100 USB Adapter Board . . . . . . . . . 15

4.6 LCD Panel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

4.7 GPIO Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6 Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

7 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8 Change Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4Seiko Epson Corporation S5U13742P00C100 Evaluation Board

Rev. 1.1

Introduction

S5U13742P00C100 Evaluation Board Seiko Epson Corporation 5

Rev. 1.1

1 Introduction

This manual describes the setup and operation of the S5U13742P00C100 Evaluation

Board. The evaluation board is designed as an evaluation platform for the S1D13742

Mobile Graphics Engine.

The S5U13742P00C100 evaluation board can be used with many native platforms via the

host connector which provides the appropriate signals to support a variety of CPUs. The

S5U13742P00C100 evaluation board can also connect to the S5U13U00P00C100 USB

Adapter board so that it can be used with a laptop or desktop computer, via USB 2.0.

This document is updated as appropriate. Please check for the latest revision of this

document before beginning any development. The latest revision can be downloaded at

vdc.epson.com.

We appreciate your comments on our documentation. Please contact us via email at

vdc-document[email protected]pson.com.

Features

6Seiko Epson Corporation S5U13742P00C100 Evaluation Board

Rev. 1.1

2 Features

The S5U13742P00C100 Evaluation Board includes the following features:

• 121-pin FCBGA S1D13742 Mobile Graphics Engine

• Header with all S1D13742 Host Bus Interface signals

• Headers for connection to the S5U13U00P00C100 USB Adapter board

• Headers for connecting to LCD panels

• Header for S1D13742 GPIO pins (optional)

• On-board 4MHz oscillator

• 14-pin DIP socket (if a clock other than 4MHz must be used)

• 3.3V input power

• On-board voltage regulator with 1.5V output

• On-board voltage regulator with adjustable 6~24V output, 40mA max., to provide

power for LED backlight of LCD panels.

Installation and Configuration

S5U13742P00C100 Evaluation Board Seiko Epson Corporation 7

Rev. 1.1

3 Installation and Configuration

The S5U13742P00C100 evaluation board incorporates a DIP switch, jumpers, and 0 ohm

resistors which allow it to be used with a variety of different configurations.

3.1 Configuration DIP Switch

The S1D13742 has 3 configuration inputs (CNF[2:0]). A DIP switch (SW1) is used to

configure CNF[2:0] as described below.

The following figure shows the location of DIP switch SW1 on the S5U13742P00C100

board.

Figure 3-1: Configuration DIP Switch (SW1) Location

Table 3-1: Summary of Power-On/Reset Options

SDU13742P00C100

SW1-[4:1] Config

S1D13742

CNF[2:0] Config

Power-On/Reset State

1 (ON) 0 (OFF)

SW1-[1] CNF0 Host Data lines are normal Host data lines are swapped

SW1-[2] CNF1 Host Data is 16-bit Host data is 8-bit

SW1-[3] CNF2 PIOVDD output current = 6.5mA PIOVDD output current = 2.5mA

SW1-[4] - not used

= Required settings when using S5U13U00P00C100 USB Adapter board

DIP Switch

SW1

Installation and Configuration

8Seiko Epson Corporation S5U13742P00C100 Evaluation Board

Rev. 1.1

3.2 Configuration Jumpers

The S5U13742P00C100 has 6 jumpers which configure various board settings. The jumper

positions for each function are shown below.

Jumper Function Position 1-2 Position 2-3 No Jumper

JP1 COREVDD Normal — COREVDD current

measurement

JP2 PLLVDD Normal — PLLVDD current

measurement

JP3 IOVDD Normal — IOVDD current

measurement

JP4 IOVDD Source H1 connector, pin 32 3.3VDD —

JP5 PIOVDD Normal — PIOVDD current

measurement

JP6 PIOVDD Source H4 connector, pin 8 3.3VDD —

= Required settings when using S5U13U00P00C100 USB Adapter board

Installation and Configuration

S5U13742P00C100 Evaluation Board Seiko Epson Corporation 9

Rev. 1.1

JP1, JP2, JP3, JP5 - Power Supplies for the S1D13742

JP1, JP2, JP3, JP5 can be used to measure the current consumption of each S1D13742

power supply.

When the jumper is at position 1-2, normal operation is selected.

When no jumper is installed, the current consumption for each power supply can be

measured by connecting an ammeter to pin 1 and 2 of the jumper.

The jumper associated with each power supply is as follows:

JP1 for COREVDD

JP2 for PLLVDD

JP3 for IOVDD

JP5 for PIOVDD

Figure 3-2: Configuration Jumper Locations (JP1, JP2, JP3, JP5)

JP3

JP5

JP1

JP2

Installation and Configuration

10 Seiko Epson Corporation S5U13742P00C100 Evaluation Board

Rev. 1.1

JP4 - IOVDD Source

JP4 is used to select the source for the IOVDD supply voltage.

When the jumper is at position 1-2, the IOVDD voltage must be provided to the H1

connector, pin 32.

When the jumper is at position 2-3, the IOVDD voltage is provided by the 3.3V power

supply of the board.

Figure 3-3: Configuration Jumper Location (JP4)

JP4

Inhaltsverzeichnis

Andere Epson Hauptplatine Handbücher

Epson

Epson S5U13781R01C100 Bedienungsanleitung

Epson

Epson S5U13781R00C100 Bedienungsanleitung

Epson

Epson S1V30333 Bedienungsanleitung

Epson

Epson S5U13517P00C100 Bedienungsanleitung

Epson

Epson S5U1C31D50T1 Bedienungsanleitung

Epson

Epson S5U13A05B00C Bedienungsanleitung

Epson

Epson S5U13706B00C Bedienungsanleitung

Epson

Epson S5U13706P00C100 Bedienungsanleitung

Epson

Epson S1V3034x Series Leitfaden

Epson

Epson S5U1C6S3N2E2 Bedienungsanleitung

Epson

Epson S5U13T04P00C100 Bedienungsanleitung

Epson

Epson S5U13709P00C100 Bedienungsanleitung

Epson

Epson S5U13700B00C Bedienungsanleitung

Epson

Epson S5U12517P00C100 Bedienungsanleitung

Epson

Epson S5U13700B00C Bedienungsanleitung

Epson

Epson S5U13A05B00C Bedienungsanleitung

Epson

Epson S5U13A05P00C100 Bedienungsanleitung

Epson

Epson S5U13513P00C100 Bedienungsanleitung

Epson

Epson S1S65010 Bedienungsanleitung

Epson

Epson S5U13705B00C Bedienungsanleitung

Epson

Epson S5U13A04B00C Bedienungsanleitung

Epson

Epson S1D13709 Bedienungsanleitung

Epson

Epson S1R72U06 Bedienungsanleitung

Epson

Epson S1D13706 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung