Epson EpsonNet 802.11b Abmessungen

Page 1 of 6

EPSON PRODUCT SUPPORT BULLETIN

Date: 4/30/2003 Originator: DS

PSB #: PSB.2003.05.005 Authorization:

Reference: N/A Total Pages: 6

Product(s): EpsonNet 802.11b Wireless Print Server

Subject: OS X Procedure for Updating the Firmware

This bulletin was created to inform you of the procedural steps used to update the EpsonNet

802.11b Wireless Print Server firmware using the OS X Terminal Utility.

Procedure:

1.) Configure the Macintosh and the EpsonNet 802.11b Wireless Print Server for TCP/IP.

2.) Download/copy the “WLEP399.bin” firmware file to the Desktop.

3.) Navigate to Macintosh HD>Applications>Utilities>Terminal, and launch the Terminal

Utility program.

4.) At the Terminal program screen do the following:

Type cd desktop, press RETURN

Page 2 of 6

TYPE: tftp <enter the IP address of the print server> then press RETURN

Example: tftp 139.63.2.150, then press the RETURN key.

Page 3 of 6

At the tftp> prompt type the word binary, then press RETURN

Example: tftp> binary, then press the RETURN key.

Page 4 of 6

At the tftp> prompt type put <WLEP399.bin file name> then press RETURN

Example: tftp> put WLEP399.bin, then press the RETURN key.

Page 5 of 6

During the update process, you will see a message on the screen at the TFTP prompt that a

number of bytes were sent. This means the update is complete.

Note: If a timeout error occurs do the following:

Check your TCP/IP settings

Cycle the power of the print server

Run WP-Admin, click CLEAR then click START

Check the TCP/IP settings in the Configuration page of the print server, save the settings then

Quit.

Rerun step 4.

5. Next, go to the print server and perform a reset, then launch WP-Admin again to setup the

print server.

6. At WP-Admin in the search screen, click on CLEAR first, then click on START for the print

server to reappear.

Page 6 of 6

7. Open the configuration page and confirm the settings are correct, change if necessary.

8. Print the Configuration page. Click on the WP-Admin drop down menu at the top of the page

and select TEST PAGE or PRINT.

9. Save, then Quit WP-Admin.

EPSON PRODUCT SUPPORT BULLETIN

Date: 11/1/2002 Originator: JAM

PSB #: PSB.2003.01.006 Authorization:

Reference: N/A Total Pages: 5

Product(s): Epson Stylus C80WN

Subject: Enabling Wireless Encryption Protection (WEP) on Stylus C80WN and

Windows Me

This bulletin was created to inform you of a procedure to guide you through configuring

WEP on the Stylus C80WN Print Server system.

Windows Millennium Edition Instructions

Requirements:

You will need the “SSID” and “IP Settings” for your wireless network. The SSID

information is available in the properties of the wireless Ethernet interface on the

computer. The IP settings can be viewed by clicking on RUN in the Windows Start

menu, then type WINIPCFG in the RUN field and click OK. Refer to the Access

Point/Base Station’s documentation for the SSID if necessary.

Enabling WEP Encryption:

Note: To successfully enable WEP, the main item on the Print Server and Access

Point/Base station CONFIGURATION menu is the type of WEP key.

"Open" or "Shared" Key Type.

If The Epson Wireless Print Servers firmware is version 3.91 or earlier, the print server

defaults to "Open" and with no selection for "Shared" key type. Some Base Stations,

Proxim for example, default to "Shared" key type (other manufacturers may also) and

would need to be set to “OPEN” key type. Refer to the documentation for your Access

Point hardware to determine where the setting for the Key Type is found. If the Key

Types are not the same between the print server, computer and Access Point, the Host

and Print Server will not handshake properly. Even though all settings appear to be

correct, communication fails and a time-out occurs without any displaying any error

messages.

Additionally, after the Print Server, Access Point and wireless computer are configured

on the same IP address segment and communicating properly, the printer/print server's

TCP/IP address must be changed to a TCP/IP address within the same IP address

segment in order to communicate and print. The Subnet Mask and Gateway address

must match also.

To Begin:

Power-up the Printer, Print Server and Host Computer.

On the Host Computer, do the following:

1) Install, then Launch WP-Admin and click the "Start" button to begin the search.

On the EpsonNet 802.11b Print Server, do the following:

1) Push and hold in the RESET (Test/Factory) button for 10 -20 seconds. The print

server will reset to the 802.11 INFRASTRUCTURE mode settings of the host

computer running WP-Admin. This may take 2-3 minutes.

2) When the print server appears in the WP-Admin window, verify it is highlighted in the

search window and click the CONFIGURE button.

•When the PASSWORD box shows on screen, click OK without entering a

password to continue.

•When the CONFIGURATION screen appears, go to the “WEP KEY” section,

down-click and select “WEP 64BITs” or “128BITs” from the drop-down button

box.

3) Enter the encryption value in the “64Bit Key 1” box, for example 3132333435, or the

“128bit Key 1” box, for example 31323334350000000000000000.

*** Important Note *** If you forget to enter a value into the Key box and click OK to

save the settings, you will not have any communications with the print server. To

recover from this, go to the print server and repeat the restart procedure in step 1

above.

4) In the “Wireless Mode” box, verify the selection is set to INFRASTRUCTURE.

5) Next, go to the “SSID” field and type in the SSID name of the Access Point.

Example – Proxim

6) In the “Boot Method” drop-down button select STATIC (see Note), then go to the

TCP/IP address fields and enter the appropriate address, subnet mask and gateway.

Example -

IP Address: 192.168.0.8 >> 8 for the printer

Subnet Mask: 255.255.255.0

Gateway IP: 192.168.0.1 >> 1 for the Access Point

7) Click the OK button to save the new settings and the changes will be written to the

Print Server. This may take 2-3 minutes. Wait for the utility to finish.

8) Click QUIT to close the WIRELESS SERVER SEARCH box.

On the Host:

Note – If your Access Point is also a DHCP Server, skip step 1 and go to step 2.

1) Change the TCP/IP settings on the wireless notebook computer Adapter Card to the

address of the "Proxim" Base-Station. Example - 192.168.0.1

•Right click the NETWORK Icon

•Click PROPERTIES

•Down-click and highlight “TCP/IP -> WIRELESS LAN CARD”

•Click Properties button for the next screen

•In the TCP/IP PROPERTIES box, select the IP ADDRESS tab

•Click on… SPECIFY AN IP ADDRESS bullet

oEnter the appropriate IP ADDRESS values for your network

oExample - IP Address: 192.168.0.5 >> 5 for the computer (Tab between

periods)

oSubnet Mask: 255.255.255.0 >> (Tab between periods)

•Next, click on the GATEWAY tab in the TCP/IP PROPERTIES box

oIn the NEW GATEWAY box, enter the appropriate IP ADDRESS for your

network gateway

oExample - Gateway: IP 192.168.0.1 >> 1 for the Access Point

•Click the ADD button

•Click OK button

•In the lower, right of the Taskbar, click the WIRELESS icon.

oClick Advanced Configuration from the menu that appears

oClick the Configuration tab

oIn the Configuration screen, verify or enter the SSID name of the Access

Point

Example – Proxim

oClick the Apply button for any changes that have been made or click the

OK button to proceed to the next screen.

oClick the Apply button in the next screen that appears

oClick OK to close the Wireless configuration window

2) The system will prompt you to REBOOT -

“Do you want to restart your computer now?” Click the YES button.

3) After the system restarts proceed to the next step.

4) Use a WEB browser such as Internet Explorer to access the Access Point’s WEB

HOME configuration page and set the WEP encryption to match the Print Server

WEP encryption settings. NOTE: If you have a Proxy Server setting enabled in your

browser, you will need to disable it temporarily in order to access the Web HOME

page on the Access Point.

5) Type in the address of the Access Point on the address bar of the WEB browser and

hit enter. Example - HTTP://192.168.0.1

6) Find "Wireless" Configuration page for the Access Point and set as follows.

•Navigate to the CONFIGURE section for the “Wireless Setup” and match the

WEP Encryption type and value in the "WEP Data Privacy" section to the settings

of the print server.

•64 Bit Encryption using a key table like this example - Key 1: 31 32 33 34 35

•or 128 Bit Encryption using a key table like this example -

Key 1: 31 32 33 34 35 00 00 00 00 00 00 00 00

•WEP Authentication: Open System << Choose this Shared Key

•Click SAVE

•On the next screen click FINISHED

7) Close the browser.

8) Go to the property settings of the Computer's Adapter Card.

•Right click NETWORK Icon

•Click PROPERTIES

•Highlight the WIRELESS ADAPTER setting

•Click PROPERTIES button

•Select ENCRYPTION Tab

oEncryption (WEP) - click on the drop-down button and select “64 bit” or

“128 bit”

oClick the CREATE KEYS MANUALLY bullet

oType in 3132333435 or 31322234350000000000000000

oClick on APPLY button

oClick OK button - Next Screen

oClick OK button - to close the NETWORK box

9) Reboot the system and upon restart check the WIRELESS status monitor

10) If there are collision errors, re-enter the WEP KEY value and test WP-Admin.

Printer Driver Settings:

Andere Handbücher für EpsonNet 802.11b

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Epson Druckserver Handbücher

Epson

Epson C12C823912 - Net 2 Print Server Bedienungsanleitung

Epson

Epson EpsonNet 10/100 Base Tx Int. 5e Bedienungsanleitung

Epson

Epson C12C824052 (Internal Type-B 10/100Base-T High Speed Ethernet Print... Bedienungsanleitung

Epson

Epson C82362 Gebrauchs- und Pflegehandbuch

Epson

Epson C12C823912 - Net 2 Print Server Bedienungsanleitung

Epson

Epson C82378 Gebrauchs- und Pflegehandbuch

Epson

Epson M286A Bedienungsanleitung

Epson

Epson C823781 - Net Print Server Firmware-Update

Epson

Epson RIP Station 5100 Service-Handbuch

Epson

Epson EpsonNet C82391 Service-Handbuch

Epson

Epson C823781 - Net Print Server Gebrauchs- und Pflegehandbuch

Epson

Epson C32C824461 - UB R03 Print Server Gebrauchs- und Pflegehandbuch

Epson

Epson C823622A - Interface Type B Print Server Bedienungsanleitung

Epson

Epson C823622A - Interface Type B Print Server Abmessungen

Epson

Epson EpsonNet 802.11b Bedienungsanleitung

Epson

Epson C823781 - Net Print Server Abmessungen

Epson

Epson C823781 - Net Print Server Bedienungsanleitung

Epson

Epson EpsonNet 802.11b Bedienungsanleitung

Beliebte Druckserver Handbücher anderer Marken

Digitus

Digitus DN-13003-1 Bedienungsanleitung

Intellinet

Intellinet 509077 Bedienungsanleitung

Atlantis Land

Atlantis Land NETSERVER A02-PSU_GX02 Bedienungsanleitung

Buffalo

Buffalo LPV4-U2-300S Bedienungsanleitung

Zonet

Zonet ZPS1000 Bedienungsanleitung

TRENDnet

TRENDnet TEW-P11G Bedienungsanleitung

Axis

Axis 140 BJC Bedienungsanleitung

HP Jetdirect 280m - 802.11b Wireless Print... Bedienungsanleitung

MicroNet

MicroNet SP766W Bedienungsanleitung

NETGEAR

NETGEAR PS104 - Hub - EN Bedienungsanleitung

Axis

Axis AXIS 1610 Bedienungsanleitung

Buffalo

Buffalo LPV4-U2-300S Bedienungsanleitung

Axis

Axis 5600+ Bedienungsanleitung

Edimax

Edimax PS-1206PWg Bedienungsanleitung

LevelOne

LevelOne WPS-9123 Bedienungsanleitung

NETGEAR

NETGEAR PS105 Bedienungsanleitung

Xerox

Xerox FreeFlow Print Server V9 SP3 Bedienungsanleitung

SEH

SEH primos Bedienungsanleitung