Epson Stylus Pro 4880 ColorBurst Edition - Stylus Pro 4880... Bedienungsanleitung

Epson Stylus®Pro 4880

QUICK REFERENCE GUIDE

Printed in USA

CPD-23920

Control Panel Lights and Buttons

Menu button

Hold for 3 seconds to

clean the print head.

Up arrow button

Paper light

Down arrow button

Left arrow or Paper

Source button

Hold for 3 seconds

to cut roll paper after

printing.

Ink light

Pause light

and button

Hold for 3 seconds

to cancel a print job

or reset the printer.

Power button

10 Feed the paper all the way through the printer until

it is aligned with the OTHERS mark on the paper

tray cover. Align the right edge of the paper with

the vertical mark on the right side of the tray cover.

Then return the paper lever to the secured position

and close the roll paper cover.

The printer automatically feeds the paper to the

printing position.

Caution:To prevent creasing the paper, remove it

from the paper path and roll it up when you’re not

printing.

Loading Roll Paper

1 Slide the black paper stop off the end of

the spindle.

Note:To use paper with a 2-inch core, remove the

gray adapters from the paper stops at each end.

See your Printer Guide for details.

2 Position the roll as shown, then slide it onto

the spindle.

3 Slide the black paper stop back onto the spindle and

insert it ﬁrmly into the end of the roll.

4 Open the roll paper cover.

5 Place the roll paper in the printer as shown. (The

black end of the spindle goes on the left.)

6 Make sure the printer is turned on, then press

the paper source button until the or

icon appears.

OTHERS

7 Raise the roll paper support on top of the paper

tray cover.

8 Release the paper lever.

9 Hold both sides of the paper and feed it into

the slot.

5 Load the sheets in the portrait orientation, short

edge ﬁrst, with the printable side face-down. Place

the paper all the way back, against the right side of

the tray.

Don’t load paper above the arrow mark inside the

edge guide.

Caution: When you add more paper, always line up

the edges with the paper already in the tray.

Loading Paper in the Tray

Make sure the printer is on and roll paper is not loaded

for printing.

1If your paper size is A3 or larger, pull out the paper

tray and cover.

2Lift up the paper tray cover.

6 Adjust the paper tray and edge guide according to

the paper size. For sheets smaller than A3, raise the

paper guide and move it to the edge of the stack.

7Flip down the paper guide roller, adjust the length

of the paper tray cover (if necessary), then replace

the paper tray cover.

Note: Make sure the roll paper support is

not raised.

8 Press the paper source button until you see the

cut sheet icon.

3 Flip up the paper guide roller and slide the edge

guide all the way to the left.

4Thumb through a stack of paper, then gently tap it

on a ﬂat surface to even the pages.

3 Open the top cover.

4 Insert the sheet face-up.

The front manual feed slot provides a straight-through

paper path for posterboard or other media 31 to 59 mil

(0.8 to 1.5 mm) thick. Make sure there is enough space

behind the printer for feeding the paper.

Note:You can also load paper through the rear

manual feed slot. See your Printer Guide for details.

1 Make sure the printer is turned on, then press the

paper source button until you see the cut sheet

icon.

2 Release the paper lever.

5 Push the sheet under the gray feed rollers,

and align the right edge with the vertical mark on

the right side of the tray cover.

6 Close the top cover.

7 Return the paper lever to the secured position. The

printer grabs the paper and feeds it into printing

position.

8 Extend the paper tray and cover to support the sheet

as it comes out of the printer. Make sure the roll

paper support is not raised.

Loading Paper Manually

Align paper with

this line for Letter-

size, A4, or B4

sheets.

Align paper with this

line for larger sheets

Checking and Aligning the Print Head

Auto Nozzle Check and

Auto Cleaning

You can turn on Auto Cleaning and Auto Nozzle Check

from the printer’s control panel to automatically check

and clean the print head nozzles before each print job.

First, make sure paper is loaded in the tray.

1 Press the Menu button to display PRINTER

SETUP. Then press the Menu button again.

2 Press the button to display AUTO CLEANING.

Then press the Menu button.

3 Press the button to choose ON, then press the

Menu button to conﬁrm the setting.

4Press the button.

5 Press the button to display AUTO NZL CK. Then

press the Menu button.

Note: When AUTO NZL CK is turned on, a nozzle

check pattern will print before each print job.

6 Press the button to choose ON, then press the

Menu button to conﬁrm the setting.

7 Press the II pause button.

Note:You can manually run a cleaning cycle by

pressing the Menu button and holding it for more

than 3 seconds.

Aligning the Print Head

If your prints look grainy or blurry, or you see

misregistration or “ghosting,” you need to align the print

head. Follow these steps to align the print head:

1 Make sure the printer is turned on. Then load

sheets of Epson Ultra Premium Photo Paper Luster

if you’re printing with Photo Black ink, or Epson

Ultra Premium Presentation Paper Matte if you’re

printing with Matte Black ink.

2 Press the Menu button.

3 Press the button to display HEAD ALIGNMENT.

Then press Menu. You see PAPER THKNS.

4Press the Menu button again, then press the

button to display STD. This is the correct thickness

setting for most Epson papers, including Epson

Ultra Premium Photo Paper Luster and Epson Ultra

Premium Presentation Paper Matte.

5 Press the Menu button to register the

value, then press the button to display

PAPER THKNS again.

6 Press the button to display ALIGNMENT.

7 Press the Menu button to display AUTO, then press

Menu again. You see UNI-D (uni-directional). This

is the type of alignment to start with.

1 2 3 4 5 6 7 8

3sec.

HEAD ALIGNMENT

PAPER THKNS

8 Press the Menu button again to start the alignment

process. Head alignment takes about 12 minutes.

Caution: Make sure you don’t open the top cover or

turn off the printer during the alignment process.

9 When the uni-directional alignment is ﬁnished, press

the button until you see BI-D 2-COLOR.

Then press the Menu button again to start the

bi-directional black alignment. The alignment takes

about 7 minutes.

10 When the bi-directional black alignment is ﬁnished,

press the button until you see BI-D ALL. Then

press the Menu button again to start the ﬁnal

alignment. The alignment takes about 17 minutes.

11 When the ﬁnal alignment is ﬁnished, press the

II pause button.

1 2 3 4 5 6 7 8

3sec.

ALIGNMENT AUTO

BI-D ALL

Continue

▲

Checking Ink Levels and Replacing Ink Cartridges

Before you begin a large print job, you should check your

ink levels. If one of your cartridges is low, you can replace

it before you start. Or you can wait until the ink runs

out, replace the cartridge, and then continue the job.

Checking Ink Levels

The easiest way to check ink levels is from the

control panel.

Replacing Ink Cartridges

When the ink light ﬂashes, one of the indicators is

low, and INK LOW is displayed on the LCD panel, the

corresponding cartridge is nearly expended. Make sure

you have the correct replacement cartridge.

You can install any combination of 110 ml and 220 ml

cartridges.

Epson UltraChrome K3TM withVivid Magenta ink

110 ml 220 ml

Photo Black T605100 T606100

Cyan T605200 T606200

Vivid Magenta T605300 T606300

Yellow T605400 T606400

Light Cyan T605500 T606500

Vivid Light Magenta T605600 T606600

Light Black T605700 T606700

Light Light Black T605900 T606900

Matte Black T613800 T614800

When one of the indicators is blank and REPLACE

INK CRTG is displayed on the LCD panel, the cartridge

is expended. To replace the cartridge, ﬁrst make sure the

printer is on.

1 Press the ink compartment cover to open it.

2 Raise the ink lever to the unlocked position.

3 Remove the expended ink cartridge from the printer.

Warning: Do not shake the expended cartridge, or

ink may leak. If ink gets on your hands, wash them

thoroughly with soap and water. If ink gets in your

eyes, ﬂush them immediately with water.

4 Make sure the replacement cartridge is the correct

color, and remove it from its package.

Gently shake the cartridge before installing it.

3 Vivid Magenta 5 Light Black

(full) (empty)

1 2 3 4 5 6 7 8

3sec.

1 Photo Black/

Matte Black

2 Cyan

4 Yellow 6 Light Cyan

7 Vivid Light Magenta

8 Light Light Black

Replacing Printer Parts

Replacing Ink Cartridges (continued)

5 Hold the cartridge with the arrow mark pointing

toward the printer. Then insert the cartridge into the

slot. Don’t force it.

Note: If you can’t insert the cartridge smoothly,

you may have the wrong cartridge. Check the

package and product code. If the ink light remains

on after installing the cartridge, try removing and

then reinserting it.

6 Return the ink lever to its locked position.

7 If you’re using 110 ml cartridges, close the ink

compartment cover. If you’re using 220 ml

cartridges, you’ll have to leave the cover open.

Replacing the Cutter Blade

If you notice that the paper isn’t cut cleanly, you may need

to replace the cutter blade (part # C12C815291). You can

check its status as described below:

1 Press the Menu button on the printer, then press the

button until you see PRINTER STATUS.

2 Press Menu, then press the button until you see

SERVICE LIFE.

3 Press the Menu button, then press the button until

you see CUTTER. E*****F indicates a new cutter. If

no stars are displayed, the cutter needs to be replaced.

Caution: Do not use the cutter for the

following media:

• Fine art paper (such as Epson UltraSmooth®

Textured, or Velvet)

• Canvas

• Vinyl

• Matte board

• Heavyweight polyester banner media

Follow these steps to replace the cutter:

1 Press the Menu button on the printer, then press

the button until you see CUTTER REPLACE.

2 Press the Menu button to display EXEC, then press

the Menu button again. The print head moves to the

cutter replacement position.

3 Open the top cover.

Continue

▲

Replacing Printer Parts (continued)

4 Hold down the side pin, as shown, then turn the

latch to the right.

5Release the side pin and carefully remove the cutter

blade.

Replacing the Maintenance Tank

You need to replace the Maintenance Tank

(part # C12C890191) when you see MNT TNK FULL

on the LCD display. The ink light also turns red.

Note: If you are using 220 ml ink cartridges, remove the

four cartrides from the right ink compartment, then close

the compartment cover.

1 Pull out the maintenance tank as shown.

Caution: Do not tip the tank, or ink may spill out.

2 Place the used tank in the plastic bag included with

the new tank.

6 Insert the new cutter blade.

7 Hold down its side pin and secure it with

the latch.

8 Close the top cover. The carriage returns to the home

position and the cutter replacement is complete.

3 Insert the new tank.

Note: If you removed any 220 ml ink cartridges,

replace them after inserting the new

maintenance tank.

Error messages

For a complete list of error messages, see your Printer Guide.

Control Panel Messages

Message Light Explanation or response

READY Pause light off Printer is ready to print.

PRINTING Pause light ﬂashing Printer is receiving data.

RESET All lights ﬂash brieﬂy Printer is resetting.

PRESS PAUSE BUTTON Pause light on Press the pause button to continue.

PLEASE WAIT Pause light ﬂashing Printer is initializing or performing maintenance. Wait

until READY appears.

PAUSE Pause light on Printer is paused.To resume printing, press the

pause button.

CUTTING Printer is cutting the paper.

CHARGING INK Printer is charging the ink delivery system. Wait until

READY appears.

Status messages

These messages indicate normal phases of printer operation.

Continue

▲

Response

Replace ink cartridge(s) indicated

on LCD. See page 5.

Replace ink cartridge(s) indicated

on LCD. See page 5.

Make sure the right paper is loaded

and the paper source setting is the

same on the control panel and print

options.

Move the paper lever to the

secured position.

Make sure paper is loaded correctly

and the paper lever is secured. If

you’re using cut sheets, make sure

the paper is ﬂat.

Replace the maintenance tank. See

page 7.

Explanation

Ink cartridge(s) are nearly

expended (printing continues).

Ink cartridge(s) are expended

(printing stops).

The paper source setting in

print options is different

from the control panel setting.

The paper lever is in the

released position.

The printer cannot detect

the paper.

The maintenance tank is full.

Light

Ink light ﬂashing

Ink light on

Paper light on

Ink light on

Message

INK LOW

REPLACE INK CRTG

CHANGE PAPER

TYPE

LOAD PAPER

SET PAPER LEVER

RELOAD PAPER

MNT TNK FULL

Where To Get Help

Control Panel Messages (continued)

Error messages (continued)

Epson and Epson Stylus are registered trademarks and Epson UltraChrome K3 and Epson Exceed Your Vision are trademarks of Seiko Epson

Corporation. UltraSmooth is a registered trademark and Epson Preferred is a service mark of Epson America, Inc.

Service

Telephone support

World Wide Web

Support for non-Epson RIP

Access

Call (888) 377-6611. Make sure

you have your Unit ID number.

If you experience any difﬁculty with the toll-free number or your Unit ID

number, call (562) 276-1305.

Go to epson.com/support to download drivers and ﬁrmware, access

product documentation and troubleshooting, and get technical advice

through e-mail.

Contact the RIP manufacturer.

Response

Release the paper lever. Remove

the paper tray if you’re printing on

cut sheets. Remove the jammed

paper. If necessary, open the top

cover or remove the rear cover.

Reload paper, making sure the

edges are straight.

Check to make sure the green

tab on the print head is pulled

out until it stops. If so, note the

error number, and turn the printer

off and then on. If the message

remains, contact Epson®.

Explanation

Paper has jammed in the

printer.

Paper was fed at an angle.

The print head is locked or

an error has occurred.

Light

Paper light ﬂashing

All lights ﬂashing

Message

RELEASE LEVER

REMOVE PAPER JAM

PAPER NOT STRAIGHT

SERVICE REQ.

Epson PreferredSM Unit ID number

Date of purchase

Serial number

Andere Handbücher für Stylus Pro 4880 ColorBurst Edition - Stylus Pro 4880...

Inhaltsverzeichnis

Andere Epson Drucker Handbücher

Epson

Epson JetPlate 7600 Montageanleitung

Epson

Epson Expression Home XP-200 Bedienungsanleitung

Epson

Epson SC-F7000 Series Bedienungsanleitung

Epson

Epson LQ-2090 Bedienungsanleitung

Epson

Epson Stylus C62 Bedienungsanleitung

Epson

Epson U950 - TM B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson ET-M16600 Series Bedienungsanleitung

Epson

Epson EMP 750 Bedienungsanleitung

Epson

Epson EPL-N2550 Bedienungsanleitung

Epson

Epson TM-L90-i Gebrauchs- und Pflegehandbuch

Epson

Epson XP-8600 Small-in-One Bedienungsanleitung

Epson

Epson C2600/2600 Bedienungsanleitung

Epson

Epson AcuLaser CX28 Series Originalbetriebsanleitung

Epson

Epson TM-J9000 Series Bedienungsanleitung

Epson

Epson TM950 - B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson ET-4700 Series Bedienungsanleitung

Epson

Epson Artisan 837 Bedienungsanleitung

Epson

Epson Stylus C120 Series Bedienungsanleitung

Epson

Epson TM-T88IV ReStick Gebrauchs- und Pflegehandbuch

Epson

Epson CW-C6000A Gebrauchs- und Pflegehandbuch

Epson

Epson Stylus SX440W Montageanleitung

Epson

Epson Printer Installationsanleitung

Epson

Epson Stylus Office BX305F Montageanleitung

Epson

Epson ET-3850U Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung