Epson Stylus Pro 7600 Photographic Dye Ink Technisches Handbuch

Manual Update for Stylus Pro 7600/9600

Unpacking and Setup Guide

Choosing a place for the printer

The second condition on page 2 is incorrect. Leave at least 30 cm between the back of the printer and the wall.

Unpacking the printer

Steps 1 to 4 on pages 4 to 5 for Stylus Pro 9600 users and steps 1 to 3 on pages 9 to 10 for Stylus Pro 7600 users

have been changed as described below.

1. Remove the roll paper spindle with roll paper, polystyrene foam, and cardboard cushions from around

the printer.

2. Stylus Pro 7600 users should remove the fixers from the sides of the box.

3. Lift the box up and away from the printer. Remove the ink cartridges from the right hollow (A), and

draining cartridge, ferrite core, flanges and roll paper belt from the left hollow (B) on the rear side of the

printer.

Note:

❏For EPSON UltraChrome ink users, 8 ink cartridges are included. For dye ink users, 7 ink cartridges are

included.

❏The draining cartridge is used for EPSON UltraChrome black ink replacement.

4. Take out the cardboard panels from the printer.

xxx

5. Stylus Pro 7600 users should remove the polystyrene foam stoppers under the printer.

Mounting the printer on the base unit (Stylus Pro 9600 only)

The figure in step 5 on page 6 has been changed as shown below. Fasten the bottom of the printer and base

unit with wing nuts, spring washers, and washers.

Removing the protective materials

Remove the tape from the maintenance tank on the right side of the printer.

Attaching the paper basket (Stylus Pro 9600 only)

Step 4 on page 7 has been changed as described below.

After passing the rear shaft under the horizontal strut, rotate the rear paper basket joints to enfold the bar that

is not attached to the fabric, as shown below. Then follow the instructions in the Unpacking and Setup Guide.

Assembling the Stand (Stylus Pro 7600 only)

The figure in step 3 on page 11 has been changed as shown below. Insert the bottom horizontal strut into the

right and left bases as shown. Use hex wrench to fasten the strut with collars and strut bolts.

spring washer

wing nut

washer

The figure in step 4 on page 11 has been changed as shown below, but the assembling procedure is the same

as described in the Unpacking and Setup Guide.

Installing the ink cartridges

The time required for ink charging has been changed to about 10 minutes. While the Pause light is flashing,

make sure to observe the caution at the end of step 7 on page 14, and do not remove the maintenance tank.

Installing the optional interface card

To install an optional interface card, follow these steps:

Note:

Before you install the optional interface card, see the documentation that comes with the card for setup information.

1. Make sure the printer is turned off.

2. Make sure that the power cord is unplugged from the electrical outlet.

wWarning:

Do not install the interface card when the printer is connected to an electrical outlet. Doing so may damage the

printer.

3. Disconnect the interface cable, if necessary.

4. Use a cross-head screw driver to remove the two screws securing the shielded plate to the optional

interface slot, and lift off the plate. Be sure to keep the screws to use when you re-install the shield printer.

Note:

Do not remove any other screws around the shield plate.

5. Set the DIP switches and jumpers on the card, if necessary. See the interface card’s documentation for

details.

6. Slide the interface card along the slots on both sides of the interface compartment. Push it in firmly to fully

insert the connector at the rear of the interface card into the printer’s internal socket.

7. Secure the interface card in the slot with the two screws included with the interface card.

8. Connect a compatible interface cable to the interface card and to your computer. If the cable has a ground

wire, secure it with one of the screws.

When connecting your printer and computer with the IEEE1394 interface board, attach the ferrite core

that is packed with your printer to the cable as shown.

Also, if you are using more than one computer, reconnect the other interface cable.

9. Make sure the printer is turned off. Then plug in the power cord.

To remove an interface card, follow the above steps in reverse order.

Reference Guide

❏The product code for the Photo Black ink cartridge is wrong. The correct product code is T5431.

❏The product code for the Auto Take-Up Reel Unit is wrong. The correct product code is C12C815251.

❏The units for Paper Feed Adjustment are 0.01%.

❏Roll Feed Spindle 2 inch (High tension / for Stylus Pro 7600) and Roll Feed Spindle 3 inch (High tension

/ for Stylus Pro 7600) cannot be used with the Stylus Pro 7600. The only high-tension spindle that can be

used with Stylus Pro 7600 is the 2/3 inch Dual Roll Feed Spindle, C12C811155.

Printed in Japan xx.xx-xx

Andere Handbücher für Stylus Pro 7600 Photographic Dye Ink

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Epson Drucker Handbücher

Epson

Epson R260 - Stylus Photo Color Inkjet Printer Bedienungsanleitung

Epson

Epson Stylus NX105 Bedienungsanleitung

Epson

Epson Stylus C86 Bedienungsanleitung

Epson

Epson C120A Bedienungsanleitung

Epson

Epson WorkForce WF-2960DWF Bedienungsanleitung

Epson

Epson Small-in-One XP-400 Bedienungsanleitung

Epson

Epson TM-U220 Series Bedienungsanleitung

Epson

Epson Stylus Photo 750 Bedienungsanleitung

Epson

Epson ActionLaser 1600 Bedienungsanleitung

Epson

Epson SureColor SC-F7000 Bedienungsanleitung

Epson

Epson DLQ-3500 Bedienungsanleitung

Epson

Epson WorkForce 60 Referenzhandbuch

Epson

Epson LQ-570+ Bedienungsanleitung

Epson

Epson LX-300+II RTP Bedienungsanleitung

Epson

Epson Stylus TX410 Series Montageanleitung

Epson

Epson PictureMate Express Bedienungsanleitung

Epson

Epson U590P - TM B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson U950 - TM B/W Dot-matrix Printer Bedienungsanleitung

Epson

Epson SureLab D870 Bedienungsanleitung

Epson

Epson TM-T88II Series Bedienungsanleitung

Epson

Epson LX-300+ Bedienungsanleitung

Epson

Epson Stylus Pro 10000 Series Bedienungsanleitung

Epson

Epson ActionLaser 1600 Merkblatt

Epson

Epson TM-T58 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung