Epson 26-484-01 Bedienungsanleitung

Page 1Extron • System 8/10 PLUS • User’s Manual • P/N 68-424-01 Rev. D

Epson Installation Configuration and Connections

SYSTEM 8/10 Plus

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITHTHE FOLLOWING COMPONENTS:

Kit Type: EPSON

Included Communications Adapter(s):

Quantity Part Number Description

1 26-484-01 ADP, UNV, “I”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔”IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: EPSON EMP 5300/7100/

7300/7550

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 45678910Adapter

✔EMP5300/7100 0 0 E 2 J2 ↓↓↑↓↑↓↓ ↓↑↓26-484-01

✔EMP7300/7550 0 0 E 2 J2 ↓↓↑↓↑↓↓ ↓↑↓26-484-01

EMP8000/7250 0 0 E 6 J2 ↓↓↑↓↑↓↓ ↓↑↓26-484-01

EMP8100/7700 1 0 E 6 J2 ↓↓↑↓↑↓↓ ↓↑↓26-484-01

EMP7600/5600 2 0 E 6 J2 ↓↓↑↓↑↓↓ ↓↑↓26-484-01

Page 2Extron • System 8/10 PLUS • User’s Manual • P/N 68-424-01 Rev. D

Epson Installation Configuration and Connections

Epson 5300/7250/7300 Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Epson 5300/7300

projector. The general setup is explained on page 3-4 and the switch settings for

the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

✔Epson 5300 0 0 E 2 J2 ↓↓↑↓↑↓ ↓↓↑↓ 26-484-01

✔Epson 7300 0 0 E 2 J2 ↓↓↑↓↑↓ ↓↓↑↓ 26-484-01

_ RS5 is for RGB switching

delay. See page 3-4 for

more information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Epson 5300/7300”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and

the others down. See illustration to the left.

Use the illustration on the facing page to do the following steps.

5. Connect the projector’s Com cable to the Com 1 DIN connector of the projector.

6. Connect the Comm Adapter’s 9-pin female connector to the 9-pin male

connector of the projector cable. Connect the other end of the Comm Adapter to

the Communications extension cable (CC-50' or CC-100').

7. Connect the CC cable to the 15-pin HD “Projector Control” port located on the

rear panel of the System 8/10 PLUS.

______ Secure the screws on all D connectors.

8. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the

Epson projector inputs according to the application requirements.

9. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

Configured For:

RS-232

34567891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Page 3Extron • System 8/10 PLUS • User’s Manual • P/N 68-424-01 Rev. D

Epson Installation Configuration and Connections

10. Power on the projector with either the remote control or by pressing the

projector’s power button.

11. Press the projector’s Menu button, then select Options and enter this selection.

12. Select Mouse/Com 1, then select BNC Format RGB and enter this selection.

_ When the projector and switcher are communicating with each other, there will be a delay of

30 to 60 seconds when powering the projector on/off using the System 8/10 Plus.

Epson 5300/7300 Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to an Epson

5300/7300 projector. Refer to Epson documentation to continue the installation.

_ You cannot input S-video and Composite video sources simultaneously

_ If the installation includes looping (master/slave) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

15-Pin HD

CC 50'

Comm

Adapter

26-484-01

"I"

9-Pin

"I"

Male

9-Pin

3, 4 or 5 BNC

See note

below

○○○○○○○○○○○○○○○○○○○

Page 4Extron • System 8/10 PLUS • User’s Manual • P/N 68-424-01 Rev. D

Epson Installation Configuration and Connections

Epson 8000/7250 Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Epson 8000/7250

projector. The general setup is explained on page 3-4 and the switch settings for

the projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS

front panel. See bottom of page 3-3. The label on the back of the access cover

also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Epson 8000/7250 0 0 E 6 J2 ↓↓↑↓↑↓ ↓↓↑↓ 26-484-01

_ RS5 is for RGB switching

delay. See page 3-4 for

more information on switch

functions.

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next

to “Epson 8000/7250”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.

Unless this is part of a master/slave system, set #3 and #5 to the up position and

the others down. See illustration to the left.

Use the illustration on the facing page to do the following steps.

5. Connect the projector’s Com cable to the Com 1 DIN connector of the projector.

6. Connect the Comm Adapter’s 9-pin female connector to the 9-pin male

connector of the projector cable. Connect the other end of the Comm Adapter to

the Communications extension cable (CC-50' or CC-100').

7. Connect the CC cable to the 15-pin HD “Projector Control” port located on the

rear panel of the System 8/10 PLUS.

______ Secure the screws on all D connectors.

8. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the

Epson projector inputs according to the application requirements.

9. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The

Main Power LED should light. Apply power to the projector.

Configured For:

RS-232

34567891012

SW15 DIP Switch

RS5 RS2

RS2

RS1

RS3

RS4

RS1

RS3 RS4

Page 5Extron • System 8/10 PLUS • User’s Manual • P/N 68-424-01 Rev. D

Epson Installation Configuration and Connections

10. Power on the projector with either the remote control or by pressing the

projector’s power button.

11. Press the projector’s Menu button, then select Options and enter this selection.

12. Select Mouse/Com 1, then select BNC Format RGB and enter this selection.

_ When the projector and switcher are communicating with each other, there will be a delay of

30 to 60 seconds when powering the projector on/off using the System 8/10 Plus.

Epson 8000/7250 Projector Connections

Use the illustration below when connecting the System 8/10 PLUS to an Epson

8000/7250 projector. Refer to Epson documentation to continue the installation.

_ If the installation includes looping (master/slave) switchers, see Chapter 5.

If Video Loop Back is part of the installation, see pages 2-10 and 2-11.

15-Pin HD

CC 50'

Comm

Adapter

26-484-01

"I"

9-Pin

"I"

Male

9-Pin

3, 4 or 5 BNC

○○○○○○○○○○○○○○○○○○○○○○○

Inhaltsverzeichnis

Andere Epson Projektorzubehör Handbücher

Epson

Epson ELPMB75 Bedienungsanleitung

Epson

Epson ELPIU03 Bedienungsanleitung

Epson

Epson ELPLX01 Bedienungsanleitung

Epson

Epson ELPWP10 Bedienungsanleitung

Epson

Epson BrightLink 450Wi - Interactive Projector Leitfaden

Epson

Epson BrightLink Solo Interactive Module (IU-01 Bedienungsanleitung

Epson

Epson Panamorph ELPALK2 Bedienungsanleitung

Epson

Epson ELPMB56 Bedienungsanleitung

Epson

Epson 7900p - PowerLite XGA LCD Projector Bedienungsanleitung

Epson

Epson ELPMBATA - High Security - Mounting Bedienungsanleitung

Epson

Epson ELPMBP03 - Structural Round Ceiling Plate Leitfaden

Epson

Epson EB-435W guide Bedienungsanleitung

Epson

Epson PowerLite 450W Stücklistenhandbuch

Epson

Epson ELPMBC01 Leitfaden

Epson

Epson PowerLite Home Cinema 700 Bedienungsanleitung

Epson

Epson ELPLX01WS Bedienungsanleitung

Epson

Epson BrightLink Solo Interactive Module (IU-01 Bedienungsanleitung

Epson

Epson ELPMBPJF - Universal Projector Ceiling Mount Leitfaden

Epson

Epson POWERLITE 8300I EMP-8300 Bedienungsanleitung

Epson

Epson ELPHB800 Bedienungsanleitung

Epson

Epson ELPLX03 Bedienungsanleitung

Epson

Epson ELPLL07 Bedienungsanleitung

Epson

Epson ELPMB24 Bedienungsanleitung

Epson

Epson ELPDC06 Document Camera For serial numbers beginning with LQZF - DC-06 Document... Bedienungsanleitung

Beliebte Projektorzubehör Handbücher anderer Marken

Optoma

Optoma BX-AL133B Bedienungsanleitung

PEERLESS

PEERLESS PE 1120 Leitfaden

Osram

Osram SIRIUS HRI Series Handbuch

Presentation Switchers

Presentation Switchers PS111 Bedienungsanleitung

Kramer

Kramer VIA GO Bedienungsanleitung

Yamaha

Yamaha PJL-112 Stücklistenhandbuch

Swedstyle

Swedstyle CL23AA02ZA25E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 236CB Betriebsanleitung

Acer

Acer WP100 Bedienungsanleitung

i3 i3board Bedienungsanleitung

CHIEF

CHIEF HB-43E Bedienungsanleitung

Biamp

Biamp Modena Hub Service-Handbuch

NEC

NEC MP10RX Bedienungsanleitung

Panamorph

Panamorph DCR-S3 Bedienungsanleitung

Exact solutions

Exact solutions FRAME-EVO-P10 Bedienungsanleitung

CHIEF

CHIEF VCM103S Bedienungsanleitung

InFocus

InFocus LP70+ Leitfaden

Sharp

Sharp AN-PH20EZ Bedienungsanleitung