Epson Elp-3000 Abmessungen

Page 1of 1

EPSON PRODUCT SUPPORT BULLETIN

Date: 04/02/2002 Originator: JAM

PSB #: PSB.2002.04.004 Authorization:

Reference: Report #02-37 Total Pages: 1

Product(s): ELP-3000 / 3300 / 3500, PowerLite 5000 / 5000XB / 7000 / 7000XB / 7300

Subject: Computer DVD video tearing on Epson Projectors

This bulletin was created to inform you of DVD video tearing on Epson projectors manufactured

prior to June 1998.

Models affected:

ELP-3000 ELP-3300 ELP-3500 PowerLite-5000

PowerLite-7000 PowerLite-5000XB PowerLite-7000XB PowerLite-7300

Description of artifact:

When playing high image contrast, fast-action DVD movies, a very thin horizontal break can occur

in the image. The line-tear is very difficult to see if the viewing environment is moderately or

brightly lit. Most viewers will not notice it. This line-tear can occur at the top, middle or bottom of

the screen as the movie continues to play. The tearing occurs about every 5 to 8 minutes of play

and can be seen for the duration of the movie. The break can also appear to travel vertically over

time because of timing differences between video frame rates and projector refresh cycles. The

artifact only occurs when playing movies from a Computer DVD player through the VGA port.

There is no video tearing of the same motion picture through the S-Video, Composite or

Component input ports on the projector. The artifact appears only in the video display. The audio

track is unaffected. The issue is not dependent on PC or Mac hardware platforms, operating

system or DVD player software.

Reasons:

Digital video playback through computers was not prevalent until the mass production of

Computer DVD players. With the incorporation of NTSC video frames embedded into RGB

computer video signals, synchronization limitations (frame shift) were encountered. In June 1998,

Epson incorporated frame synchronization circuitry for future projector models to eliminate the

artifact.

Resolution: Because the introduction of Computer DVD playback occurred after the manufacture

of the mentioned projectors, Epson has no plans to replace or upgrade the models specified.

Page 1 of 2

EPSON PRODUCT SUPPORT BULLETIN

Date: 06/30/2000 Originator: ESC

PSB #: PSB.2000.07.001 Authorization:

Reference: N/A Total Pages: 2

Product(s): Multimedia Projectors

Subject: Multimedia Projector Accessories – Ceiling Mounts and Suspension Adapters

This bulletin provides specification and warranty information on Ceiling Mounts and

Suspension Adapters for EPSON Multimedia Projectors:

CEILING MOUNTS:

Part Number: ELPMB31

Compatibility: PowerLite 5300, 5350, 7200, 7250, 7300, 7350,

8000i, 8000NL, 9000i and 9000NL

Dimension: 11.6” x 10.8” x 1.5”

Part Number: ELPMB32

Compatibility: PowerLite 500C, 700C and 710C

Dimension: 7.2” x 9” x 1.5”

Part Number: ELPMB33

Compatibility: PowerLite 5500C, 5550C, 7500C, and 7550C

Dimension: 10.7” x 9.6” x 1.8”

Warranty: 30-days whole unit exchange

Description: Epson’s ceiling mounts provide the added flexibility of

mounting a PowerLite projector on the ceiling. They are

designed to be installed easily and include a quick release

feature for removal of the projector so it’s easy to change the

lamp, or remove the projector for portable use. The ceiling

mounts can also be used for rear projection applications.

Each ceiling mount is custom designed for use with a specific

Epson projector.

Page 2 of 2

SUSPENSION ADAPTERS:

Part Number: ELPMBAST

Compatibility: ELPMB31, ELPMB32 and ELPMB33

Dimension: 1 l/2” Pipe

Part Number: ELPMBAPS

Compatibility: ELPMB32 and ELPMB33

Dimensions: 1” Pipe

Warranty: 30-days whole unit exchange

Description: Adjustable tubing extensions to increase the distance from the

ceiling to the projector—adjustable from 12” to 46”.

Page 1of 1

EPSON PRODUCT SUPPORT BULLETIN

Date: 06/02/2000 Originator: ESC

PSB #: PSB.2000.06.001 Authorization:

Reference: N/A Total Pages: 1

Product(s): Multimedia Projectors

Subject: Projector Compatibility with iMac’s

This bulletin provides useful information on how to connect EPSON Multimedia Projectors to

iMac models that have no external video port and have Mac OS 8.1, 8.5 or 8.6 factory

installed.

Problem:

The earlier versions of the iMac’s do not have an external video port to connect an EPSON

projector. It is possible to output video signal from the iMacs by using a third party external

video adapter.

Resolution:

The current line of EPSON's multimedia projectors do support the iMacs, using the

recommended third party external video adapter from PowerR, at the supported video

resolution 1024 x 768 with refresh rate of 75Hz. The iPresenter video adapter is

a compact device that installs into an Apple iMac computer.

iPresenter RGB Video Adapter for iMac

Model: iP-10

Power R Inc.

756 Aloha Street

Seattle, WA. 98109

(800) 729-6970

www.powerr.com

Supports iMac version:Supported Video Resolution

Versions A,B,C,D – no video out 1024 x 768, 75Hz

Page 1of 1

EPSON PRODUCT SUPPORT BULLETIN

Date: 05/18/2000 Originator: AP

PSB #: PSB.2000.05.001 Authorization:

Reference: N/A Total Pages: 1

Product(s): Multimedia Projectors

Subject: Multi-Monitor Support Function of Newer Macintosh Notebook Computers

This bulletin provides configuration procedures for the newer Macintosh notebook computers

with the EPSON Multimedia Projectors.

Problem description:

When the projector is connected to an Apple notebook, part of the Mac OS desktop may not

display on either the LCD panel or the projector. Often, only the desktop wallpaper is visible on

one screen, with the other containing the complete video output.

Reason:

Newer Macintosh notebook computers are often configured for extended desktop video output

instead of video mirroring. This results in partial information being sent to either the LCD

panel or the projector. This feature has been observed on Powerbook and G3 Powerbook

models running Mac OS 8.x and later, but it is possible the issue has been experienced by

other Macintosh users.

Resolution:

1. Click the Apple Menu to select the Control Panels, Monitors and Sound option.

When the projector is powered on while connected to the computer, there will be an

“Arrange” icon in the Monitors and Sound control panel.

2. Click the “Arrange” icon to access that control. In the “Arrange” control view window, there

should be icons for two monitors.

3. Click one of the monitor icons and drag it on top of the other monitor icon. Release that

icon on the other icon. This enables dual display support where both screens receive and

display all video information.

EPSON

RODUCT

UPPORT

ULLETIN

Date: 10/25/1996

PSB No.: PSB.1996.10.003

Reference: ELP-3000, ELP-3300 USER GUIDE

Originator: BS

Authorization:

jJ&

Affected Product(s): ELP-3000 & ELP-3300

Subject: USING TEE REMOTE CONTROL UNlT AS A POINTING DEVICE

This guide is intended to provide instructions for using the projector’s remote control unit as a painting device to

control presentation software running on a computer.

The guide assumes the user to be somewhat familiar with the computer they are using to run the presentation

software, and the basic operation of the projector. For detailed instructions on specific computer or projector

functions or operation refer to the appropriate user guide.

Most Windows-based presentation software can be controlled in a number of ways:

Directly by the computer’s pointing device (ie. wired PS/2 or Serial Mouse, Trackpad,

Trackball or other device).

With a wireless pointing device such as an infrared pointing device.

HINT!:

This could be an alternate solution to using the projector’s remote control unit.

With the projector’s Remote Control Unit.

The following steps should be completed in sequence to successfully use the Remote Control Unit as a pointing

device.

ITEMSREQUIRED

The following projector accessory items, included with the projector, will be required to use the Remote

Control Unit as a painting device: Remote Control Unit, 2 AA Batteries, ELP PC Utilities Disk, and the

6 ft. Serial cable.

CONNECTlNG THE SERIAL CABLE

Turn both the Projector and Computer OFF.

Open the I/O door located below the handle of the projector, then plug in the round

serial connector on the cable into the serial port on the projector.

Attach the 9 pin connector on the serial cable to the computer’s 9 pin Com 1 serial port.

Page 1 of 4

SETTING THE PROJECTOR FOR A SERIAL CONNECTION

Turn the projector ON.

Press the MENU button.

Go to the OPTIONS MENU and make sure the SERIAL option is checked

HINT!: Changing MENUS,

SELECTIONS, and FUNCTIONS

PRESSING

sync-/+

ACTION

Changes Menus (Computer, Video, Display, Audio,

OPTIONS, Custom).

Bright-/+

Changes between selections within a menu.

Vol. - / + Changes the function of a menu selection.

Exit the MENU mode by pressing the MENU button.

INSTALLING TEE PC UTILITIES SOFTWARE

HINT!: The ELP UTILITIES software is

NOT interchangeable between the ELP-3000

and the ELP-3300 projectors

Insert the projector PC Utilities disk into the floppy drive on the computer.

For Windows 3.x, select FILE, RUN, A:\SETUP.

For Windows 95, select START, RUN, A:\SETUP

HINT!: Two

utilities will be installed on the computer:

ELP LINK This utility is used to make adjustments to the operation of the

projector such as: Brightness, Contrast, Volume etc, from the

computer.

ELP REMOTE This utility is used with the Remote Control Unit. It allows the Remote

Control Unit to be used as a pointing device to move the mouse pointer

and to control functions of a software package running on the

computer, such as a presentation program.

RUNNING TEE ELP REMOTE

PROGRAMMER UTILITY

HINT!:

To use the Remote Control Unit to control your software application the

ELP LINK utility cannot be running.

Open the ELP REMOTE PROGRAMMER utility.

Select the SPECIAL pull down menu, and make sure Serial Port 1 (Com 1) is checked.

From the SPECIAL pull down menu select the ACTIVATE function.

D. The Remote Programmer Utility must be left running for the Remote Control Unit to

function.

Page 2 of 4

TESTING THE REMOTE CONTROL UNIT

Install two fresh AA batteries in the Remote Control Unit battery compartment.

Press one of the five function buttons on the Remote Control Unit. The RED LED on the

Remote Control unit should light.

HINT!: The the

function buttons are labeled ‘L“, “R”, DRAG, PREV, and NEXT

Press one of the five function buttons again while watching the POWER LED on the top

of the projector, the POWER LED should blink when the button is pressed. This

indicates the remote is communicating with the projector.

HINT!: The Remote Control Unit has a built in GO TO SLEEP function, to prolong the

life of batteries, if there is a period of inactivity on the remote. If the remote

goes to sleep, pressing one of the five function buttons will wake up the remote.

Point the Remote Control Unit at the front or the rear of the projector and slowly roll the

trackball on the Remote Control Unit, the mouse pointer on the projected image should move.

If the mouse pointer does not move, refer to the IF YOU HAVE PROBLEMS section.

HINT!: Adjustments to the tracking speed of the Trackball, and Mouse button functions

can be changed in the SPECIAL pull down menu in the REMOTE

PROGRAMMER UTILITY.

USING THE REMOTE CONTROL UNIT

Make sure the REMOTE PROGRAMMER

utility software is running.

Start your presentation software on the computer and use the Trackball on the Remote

Control unit to position the cursor.

Normally you can control the slides in the presentation with the Remote Control’s

“NEXT,

PREV", “R” or “L” buttons.

In the Remote Programmer Utility there are pre-defined key templates for some of the

more common presentation software packages. To use a pre-defined key template select

the FILE pull down menu, then select OPEN, this will display a list of the key templates.

Highlight the template for the presentation package you are using and click OK. This

will assign the presentation functions to the five function keys on the Remote Control

unit.

For special programs, the user has the ability to reassign any of the five function keys to

perform specialized tasks. Refer to the user guide for reassigning the function of keys

with Key Help and Record mode.

Page 3 of 4

IF YOU HAVE PROBLEMS

Even if the RED LED lights on the Remote Control Unit when a function key is pressed,

the batteries could be low causing a communication problem between the remote and the

computer. Try new batteries.

If you tried new batteries and the RED LED does not light when a function button is

pressed the Remote Control Unit could be bad.

The type of Lighting or Brightness of the lighting in the room could Remote

communication problems. Try moving the remote closer to projector.

The Serial Port on the computer could be disabled, check the computer’s CMOS

SETUP.

There could be a Serial Port conflict with another device in the computer.

The Serial Port on the computer could be bad, try using a serial mouse on the port.

The Serial Cable connection could be bad, try removing the cable and reconnecting it.

The Serial Cable could be bad, try another Serial Cable.

“PROJECTOR OFF-LINE” message can occur due to any of the following:

1. Projector may be turned OFF.

2. Serial cable may not be attache4 or connected properly.

3. Serial option is not selected in the OPTIONS menu on the projector.

4. The Com port selection in the REMOTE PROG

RAMMER Special menu

does not match the actual port the serial cable is connected to on the

computer

Page 4 of 4

Andere Handbücher für Elp-3000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Epson Projektor Handbücher

Epson

Epson PowerLite S5 Series Bedienungsanleitung

Epson

Epson PowerLite 8300i withEasyMP.net module Abmessungen

Epson

Epson EB-X8 Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 9500 UB Bedienungsanleitung

Epson

Epson PowerLite 5600p Abmessungen

Epson

Epson EMP-TW100 Bedienungsanleitung

Epson

Epson BrightLink Pro 1410Wi Montageanleitung

Epson

Epson PowerLite 750c Bedienungsanleitung

Epson

Epson PowerLite 800p Bedienungsanleitung

Epson

Epson PowerLite 575W Technisches Datenblatt

Epson

Epson EMP-9100 Bedienungsanleitung

Epson

Epson PowerLite 61p Bedienungsanleitung

Epson

Epson 6100i - PowerLite XGA LCD Projector Bedienungsanleitung

Epson

Epson PowerLite 420 Bedienungsanleitung

Epson

Epson PowerLite 1825 Bedienungsanleitung

Epson

Epson EB-485Wi Bedienungsanleitung

Epson

Epson EB-770Fi Bedienungsanleitung

Epson

Epson PowerLite 525W Bedienungsanleitung

Epson

Epson EB-4750W Bedienungsanleitung

Epson

Epson EasyMP EMP-1715 Bedienungsanleitung

Epson

Epson EB-485W Bedienungsanleitung

Epson

Epson EB-1723 Bedienungsanleitung

Epson

Epson LightScene EV-110 Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 500 Stücklistenhandbuch

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung

JVC

JVC 1108TTH-AO-AO Bedienungsanleitung