Epson LCD projector Bedienungsanleitung

Page 1 of 10 Last Modified: 3/22/2010

Introduction to the LCD Projector

Introduction

The Epson LCD projector is a highly versatile presentation tool. The projector can utilize

up to two computer sources, and up to three video sources, which can be easily switched

from one source to another.

The purpose of this document is to assist the novice user in using the Epson PowerLite

600p/800p/810p Multimedia Projector. This document will cover the following areas:

•Setting up the Projector

•Using the Control Panel Options

•Focusing and Changing Image Sizes

•Connecting Additional Audio and Video Devices

•Shutting Down the LCD Projector

•Warning Lights

Page 2 of 10 Last Modified: 3/22/2010

Using the LCD Projector

Setting Up

1. Place the projector on a stable flat surface 3-40 feet from the screen.

2. Connect the computer

cable to the Computer

2/Component Video port

on the back of the

projector as shown in this

picture, and the video-

out or monitor port of your computer.

3. Connect the end of the power cord to the power inlet on the back of the projector,

and the other end to a grounded electrical outlet.

4. Remove the lens cap.

5. Press the red power button on top of the projector. The Power light

will flash for about 30 seconds before the image appears

6. Turn on your computer. If you see a new hardware wizard telling you it

has found a plug-and-play monitor, press cancel. If the message is about USB

audio, click Next and follow screen directions.

a. At this point, the computer screen should be projected onto the overhead

screen.

b. If you are using a video source, and not a computer, press play on the

video source.

7. Focus the image using the rings on the lens. You may also make the image larger

or smaller by using the Wide/Tele ring.

8. Raise the image by extending the

projector’s foot, found on the bottom,

front of the projector. The release

button for the foot is found on the lower

right side of the lens. If the projected

image is unleveled, use the back

adjustable foot. This is located on the

back of the projector, on the left side,

when viewing the back of the projector.

9. Use the keystone options to adjust the

image if it appears trapezoidal.

10. Adjust the screen image by using the

menu option described in Appendix A.

Page 3 of 10 Last Modified: 3/22/2010

Using the Control Panel Options

The control panel options are located on top of the projector above the lens. All of the

functions of the LCD projector can be controlled from the control panel. The following

list describes the functions of each button of the control panel.

Power:

•To turn on, push the red Power button.

The light will flash for about 30

seconds before the image appears.

•To turn off, push the red Power

button. You will see a confirmation

message. Press Power again to turn

off the projector.

•After turning off the power to the

projector, wait until the fan turns off

before unplugging it. Once the power

light stops flashing, and stays on, it is

safe to unplug the projector.

Help:

Push the Help button on the projector to

get...

•Help for the image

•Help for the sound

•Language selection

Computer/YCbCr:

If the projector is connected to more that

one computer or video source, press Computer/YCbCr to switch between computer

sources and/or video.

Video:

If the projector is connected to more than one video source, press the Video button to

switch between standard video and S-Video.

Menu:

Press Menu to display the 8 items of the menu screen. See Appendix A for a

description of the 8 menu items.

Esc:

When you are finished viewing menu options, press Esc to return to the main menu.

Also, press Esc to leave the menu entirely.

Page 4 of 10 Last Modified: 3/22/2010

Keystone:

If the LCD Projector is not directly in line with the projection surface, the image may

appear trapezoidal. This can be adjusted using the Keystone features on the control

panel.

•Sync+ and Sync-: Adjusts the vertical image displayed.

Can make the display larger or smaller. This is useful if

the projector is projecting at an angle up or down.

•Tracking+ and Tracking-: Adjusts the horizontal image

displayed. Can make the display larger or smaller. This

is useful if the projector is not placed directly in front of

the projection surface.

Auto:

Press this button to select an item from the menu. This button can also be pushed to

reset the projector’s tracking, sync, and position settings.

Shift:

Hold down Shift and the Tracking+ or Tracking- to eliminate vertical stripes. Hold

down Shift and the Sync+ or Sync- to increase or decrease the sharpness of the

image.

Resize:

If only part of the image is displayed, press the Resize button to compress the screen

image. Continue pressing the button to pan around the screen in the original

resolution. If projecting from video equipment, pressing Resize switches the aspect

ration between 4:3 and 16:9. If zoomed in on the image, Resize will return it to the

original display size.

A/V Mute:

This button will turn off the picture or will mute the volume.

Volume:

These buttons will increase or decrease the intensity of the volume.

Page 5 of 10 Last Modified: 3/22/2010

Focus and Changing the Image Size

Use the rings on the lens to focus the image,

or to make the image appear larger or

smaller on the projection surface.

Wide/Tele:

Moving this ring of the lens right or left

will make the projection image larger or

smaller on the projection surface.

Focus:

The frontal ring of the lens has an

adjustment that will move left or right to

focus the image on the projection

surface.

Additional Audio and Video Devices

There are a number of ports on the back of the projector. These ports can be used to

connect additional audio and video features to display in your presentation. VCRs,

DVDs, camcorders, digital cameras, or laser disk players can be connected directly to

the projector, and projected on the viewing surface. Composite video (NTSC, PAL,

Page 6 of 10 Last Modified: 3/22/2010

and SECAM formats), S-Video, and Component Video (DVD, M-II, BetaCam) can

also be supported. You can also connect to different audio sources to enhance the

audio presentation. The following list summarizes the ports available on the

projector.

Ports-

USB Ports:

This will allow you to use the projector’s remote control as a wireless mouse.

Connect one end of the cable to the projector’s USB port and the other end to the

External USB port on your computer. The LCD Projector’s USB capabilities will

also transmit audio into the projector’s speakers.

Mouse:

This will allow you to use the remote control as a wireless mouse. If your computer

has a round PS/2 port for an external mouse, you will use a PS/2 Cable to connect the

computer to the LCD Projector’s Mouse port. Connect one end of the cable to the

projector’s Mouse port, and the other end to the External mouse port on your

computer

Computer 1:

This will allow you to connect a second computer to the projector. Connect one end

of the DVI (Digital Visual Interface)-analog cable to the Computer 1 port of the

projector. Connect the other end of the cable to the computer’s video port. You must

correctly set the Comp 1 Input option from the projector’s Setting menu.

Computer 2/ Component Video:

This is required to connect the projector to your computer. Connect one end of the

computer cable to the projector’s Computer 2/Component Video port, and the other

end to your computer’s Monitor port. If you are using a component video source,

you may also plug the video into the Computer 2/Component Video port. A

component video differs from a composite video in the number of channels each

operates from. A composite video signal contains all the information needed for the

color picture in a single channel of information, while a component video signal

contains information from 3 channels. Much higher program production quality is

possible in the component domain because analog compression is used to place the

three channels of component information into the single channel of composite

information. Once compression take place it is extremely difficult to get back the

original quality of the component signal.

Audio 1:

Amplify your computer’s audio: Connect one end of audio cable to the Audio 1 jack,

and the other end to the computer’s Headphone or Audio Out jack.

Audio 2:

See directions in Video for how to incorporate audio from an outside video source.

Page 7 of 10 Last Modified: 3/22/2010

Video:

RCA A/V Cable: Connect the projector to an external video player. Connect A/V

cable (with yellow plug) to the Video-out jack on your video source. Connect the

audio parts of the cable into the Audio jacks (red and white) under Audio 2 on the

projector, and to the corresponding jacks on your video source.

S-Video:

Insert one end of the S-Video cable into the S-Video connector, and the other end into

the S-Video output port of the video source. Use the A/V cable if needed to connect

RCA audio.

Audio Out:

This will allow you to connect the projector’s speakers to external speakers. Connect

an RCA-to-3.5 mm stereo audio cable’s 3.5 mm stereo miniplug into the projector’s

audio out jack. Connect the RCA plugs to the jacks of the speaker or PA system.

Monitor Out:

This will allow you to connect your desktop computer to the projector in order to

view both the projected image and the computer screen. Disconnect the monitor

cable from your computer and connect it to the projector’s Monitor Out port. This

will also require connection of a computer cable into the projector’s Computer

2/Component Video port. Connect the other end of the cable into your computer’s

video port.

Page 8 of 10 Last Modified: 3/22/2010

Shutting Down the LCD Projector

To turn off, push the red

Power button. You will see

a confirmation message.

Press Power again to turn off

the projector.

Note: After turning off the

power to the projector, wait

until the fan turns off before

unplugging it. Once the

Power Light stops flashing,

and stays on, it is safe to

unplug the projector.

Warning Lights

Next to the Power Light are two additional warning lights. Take notice if any of these

lights appear.

If the Lamp Warning Light is flashing, notify the ITRC that the lamp needs to be

changed.

If the Temperature Status Light is flashing orange, notify the ITRC to clean the air

filter. If the Temperature Status Light is flashing red, turn off the lamp immediately,

and allow the fan to run to cool down the temperature.

Further Information

If you are having trouble with audio or video, first select the Help option on the remote

or on the projector’s control panel. For specific questions or for troubleshooting, see the

User’s Guide. On the Internet you can reach Epson’s support page at

http://support.epson.com or http://www.presentersonline.com. You can also contact the

ITRC by phone (282-5880) or email at [email protected]u. The ITRC suggests attending a

workshop on the operation of the LCD projector. For information regarding ITRC

workshops dates and registration, visit the ITRC website, at http://www.isu.edu/itrc/.

Page 9 of 10 Last Modified: 3/22/2010

Appendix A

The Menu Settings

Press menu to display the 8 items of the menu screen.

•Video:

oPosition: repositions the image

oTracking: in analog computer images, removes unwanted vertical lines

oSync: corrects fuzziness

oBrightness: lightens or darkens entire image

oContrast: adjusts difference between light and dark areas

oColor: adjusts color intensity

oTint: adjusts the balance of green to magenta

oSharpness

oColor Mode: adjusts vividness of the image color

oResolution: leave on auto unless the projector is unable to sync up with the

computer

oVideo Signal: leave on auto

oNoise Reduction: reduces visual “noise” when using test and video images

•Audio: use to select audio source or adjust volume or balance

oAudio Input: Audio 1 selected for computer sound, Audio 2 for video sound, and

USB to amplify computer sound through USB cable

oVolume:

oTreble:

oBass:

•Effect: add pointers and other annotations to the image. Effect customizes these.

oPointer/Stamp: define shape and size for pointers

oSpotlight: choose large, medium, or small spotlight

oBar: define color, width, horizontal/vertical for three different bars

oPointer Speed: low, medium, high speed

•Setting: disable sleep mode, adjust image shape, customize features

oV and H-Keystone: correct shape of uneven image

oP in P: select source used by picture-in-picture

oNo-Signal Msg: Select screen color to display when no signal is received by

projector

oPrompt: leave this ON.

oA/V Mute: Selects screen color or image when you press A/V Mute button

oComp 1 Input: Select format for input to the Computer 1 port.

oComp 2/YCbCr Input: Select format for input to Computer 2/Component Video

port

oSleep Mode: Projector turns off lamp if no input received in 30 minutes: Turn on

or off.

•User’s Logo: Transfer any image from computer or video source to the projector to use

as your startup screen

Page 10 of 10 Last Modified: 3/22/2010

•Advanced

oLanguage: Select from 9 languages to be used for menus

oStartup Screen: Display your captured image or logo when the projector starts

oColor Adjustment: Adjusts the color temperature (between 5000 and 10,000 K)

of the projected image

oRear Proj.: turn on to project from behind onto a transparent screen

oCeiling: turn on when projector is mounted upside-down from the ceiling

oCOM Port: switches between serial (RS-232C) and USB communication for

programming/projector control.

•About: view information about display settings of the computer and hours lamp has been

used

oLamp: shows hours of lamp usage

oReset lamp timer: lifespan of lamp is about 1500 hours. Reset when change the

lamp.

oVideo Source:

oInput signal:

oFrequency:

oSYNC Polarity:

oSYNC Mode:

oResolution:

oRefresh Rate:

•Reset All: return all projector settings to their default values

Idaho State University

Campus Box 8064

Pocatello, ID 83209

208.282.5880

This document may be reproduced for individual or nonprofit use. Users acknowledge that the manual, and all

copyright and other intellectual and proprietary rights therein, are and at all times shall remain the valuable property of

the author. Users agree to respect and not to alter, remove or conceal any copyright, trademark, trade name or other

proprietary marking that may appear in the manual. Please send comments to it[email protected]. For more information

about the ITRC, visit our Website at http://www.isu.edu/itrc.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Epson Projektor Handbücher

Epson

Epson EX90 Technisches Datenblatt

Epson

Epson PowerLite Pro Z8455WUNL Bedienungs- und Sicherheitshinweise

Epson

Epson EB-1776W Bedienungsanleitung

Epson

Epson EH-TW5900 Gebrauchsanweisung

Epson

Epson PowerLite Home Cinema 8100 Bedienungsanleitung

Epson

Epson BrightLink 475Wi Bedienungsanleitung

Epson

Epson EB-2247U Bedienungsanleitung

Epson

Epson EB-5535U Bedienungsanleitung

Epson

Epson PowerLite 400W Handbuch

Epson

Epson PowerLite Pro Z8000WUNL Bedienungsanleitung

Epson

Epson EMP-52 Bedienungsanleitung

Epson

Epson PowerLite G5910 Bedienungsanleitung

Epson

Epson EB-PU2213B Bedienungsanleitung

Epson

Epson 830p - PowerLite XGA LCD Projector Bedienungsanleitung

Epson

Epson PowerLite 505c Bedienungsanleitung

Epson

Epson 1700C - PowerLite XGA LCD Projector Bedienungsanleitung

Epson

Epson EB-S9 Bedienungsanleitung

Epson

Epson 755c - PowerLite XGA LCD Projector Bedienungsanleitung

Epson

Epson BrightLink 475Wi Systemhandbuch

Epson

Epson EF11 Bedienungsanleitung

Epson

Epson Home Cinema 4010 Technisches Datenblatt

Epson

Epson EMP-9300 Bedienungsanleitung

Epson

Epson EMP-1815 Bedienungsanleitung

Epson

Epson EH-TW480 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung

JVC

JVC 1108TTH-AO-AO Bedienungsanleitung