Epson PowerLite 50c Bedienungsanleitung

EPSON®PowerLite®50c/70c

Quick Setup

Connect the power cord to your projector and plug the other end into a grounded outlet.

3Connect the other end to your laptop’s video or monitor port.

1Turn on the projector first. To do so, press the red Power button.

The power light flashes green as the projector warms up,

and the projection lamp comes on in about 30 seconds.

2Turn on or restart your laptop. (Windows®only: If you see a

New Hardware Wizard screen, click Cancel.)

Turn Over

Press the red Power button twice, then let the projector cool while the power light

flashes orange (about a minute). Once the light stops flashing and stays on, it’s safe to

unplug the projector.

Never unplug the projector when the power light is green or flashing orange.

Locate everything

you’ll need

Plug in your projector

Turn on your equipment

Caution: Before unplugging the projector...

For most setups, you’ll need just these two cables:

You won’t need to install any software.

Power

Help

Make sure your projector and laptop are turned off.

Connect one end of the computer cable to the

Computer port on the projector.

Connect the projector

to your laptop

power cord computer cable

Follow these instructions to connect the projector

to your laptop. To connect other devices, such as

a VCR or desktop PC, see your User’s Guide.

power button

power light

EPSON PowerLite 50c/70c

If you see a blank screen or the No Signal message

after turning on your laptop, check the following:

Make sure the power light is green and

not flashing and the lens cap is off.

Try turning off the laptop and restarting it.

If you’ve connected more than one computer and/or video source,

you may need to press the Source button on top of the projector.

(Allow a few seconds for the projector to sync up after pressing it.)

Adjust the image

1Remove the lens cap and rotate the focus ring

to sharpen the image.

If You See a Blank Screen

Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD.

You may have to hold down the Fn (function) key while pressing it.

(Allow a few seconds for the projector to sync up after pressing

the key.) Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key let you toggle between

the LCD screen and the projector, or display on both at the same

time.

You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

If you’re using a Windows laptop:

If you’re using a Macintosh®:

CPD-11579

EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.

2Raise the image as needed. To do this, pull up the blue foot

release levers and lift the front of the projector. Once the

image is positioned where you want it, release the levers

to lock the feet in position.

3If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the

center of the screen, facing the screen squarely.

4If your image looks like or , press the + or – side of

the Keystone button to correct the shape of the image.

EPSON PowerLite 50c/70c

Note: If you see a blank screen after focusing,

see the box below.

1. From the Apple menu, select Control Panels, then click Monitors

and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display

on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

focus ring

No signal

drag one monitor icon

on top of the other

click here

select a Simulscan

resolution

click here

No signal

EPSON PowerLite 50c/70c

If you see a blank screen or the No Signal message

after turning on your laptop, check the following:

Make sure the power light is green and

not flashing and the lens cap is off.

Try turning off the laptop and restarting it.

If you’ve connected more than one computer and/or video source,

you may need to press the Source button on top of the projector.

(Allow a few seconds for the projector to sync up after pressing it.)

Adjust the image

1Remove the lens cap and rotate the focus ring

to sharpen the image.

If You See a Blank Screen

Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD.

You may have to hold down the Fn (function) key while pressing it.

(Allow a few seconds for the projector to sync up after pressing

the key.) Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key let you toggle between

the LCD screen and the projector, or display on both at the same

time.

You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

If you’re using a Windows laptop:

If you’re using a Macintosh®:

CPD-11579

EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.

2Raise the image as needed. To do this, pull up the blue foot

release levers and lift the front of the projector. Once the

image is positioned where you want it, release the levers

to lock the feet in position.

3If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the

center of the screen, facing the screen squarely.

4If your image looks like or , press the + or – side of

the Keystone button to correct the shape of the image.

EPSON PowerLite 50c/70c

Note: If you see a blank screen after focusing,

see the box below.

1. From the Apple menu, select Control Panels, then click Monitors

and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display

on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

focus ring

No signal

drag one monitor icon

on top of the other

click here

select a Simulscan

resolution

click here

No signal

EPSON PowerLite 50c/70c

If you see a blank screen or the No Signal message

after turning on your laptop, check the following:

Make sure the power light is green and

not flashing and the lens cap is off.

Try turning off the laptop and restarting it.

If you’ve connected more than one computer and/or video source,

you may need to press the Source button on top of the projector.

(Allow a few seconds for the projector to sync up after pressing it.)

Adjust the image

1Remove the lens cap and rotate the focus ring

to sharpen the image.

If You See a Blank Screen

Press the function key that lets you display on an external monitor.

It may have an icon such as , or it may be labelled CRT/LCD.

You may have to hold down the Fn (function) key while pressing it.

(Allow a few seconds for the projector to sync up after pressing

the key.) Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key let you toggle between

the LCD screen and the projector, or display on both at the same

time.

You might need to use the Display utility in the Control Panel

to enable both the LCD screen and external monitor port.

If you’re using a Windows laptop:

If you’re using a Macintosh®:

CPD-11579

EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.

2Raise the image as needed. To do this, pull up the blue foot

release levers and lift the front of the projector. Once the

image is positioned where you want it, release the levers

to lock the feet in position.

3If your image looks like or , you’ve placed the projector

at an angle to the screen. Move it directly in front of the

center of the screen, facing the screen squarely.

4If your image looks like or , press the + or – side of

the Keystone button to correct the shape of the image.

EPSON PowerLite 50c/70c

Note: If you see a blank screen after focusing,

see the box below.

1. From the Apple menu, select Control Panels, then click Monitors

and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other. This lets you display

on the projector screen as well as the LCD screen.

If this option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Perform step 1 above, if necessary.

2. Click the Monitor icon.

3. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

focus ring

No signal

drag one monitor icon

on top of the other

click here

select a Simulscan

resolution

click here

No signal

Andere Handbücher für PowerLite 50c

Inhaltsverzeichnis

Andere Epson Projektor Handbücher

Epson

Epson V11H177020 - Powerlite 76C LCD Projector Referenzhandbuch

Epson

Epson PowerLite Home Cinema 5010 Bedienungs- und Sicherheitshinweise

Epson

Epson PowerLite X12 Bedienungsanleitung

Epson

Epson PowerLite 420 Bedienungsanleitung

Epson

Epson PowerLite 70c Bedienungsanleitung

Epson

Epson EMP-7950 Bedienungsanleitung

Epson

Epson EF-100W Bedienungsanleitung

Epson

Epson PowerLite 78 Technisches Datenblatt

Epson

Epson Pro Cinema 4050 Bedienungsanleitung

Epson

Epson V11H952020 Bedienungsanleitung

Epson

Epson EB-1480Fi Bedienungsanleitung

Epson

Epson EB-X7 Bedienungsanleitung

Epson

Epson PowerLite 1770W Bedienungsanleitung

Epson

Epson BrightLink 1480Fi Bedienungsanleitung

Epson

Epson Megaplex MG-50 Bedienungsanleitung

Epson

Epson PowerLite L520W Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 6500 UB - PowerLite Home Cinema... Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 8100 Bedienungsanleitung

Epson

Epson PowerLite 54c Technisches Datenblatt

Epson

Epson PowerLite 8150i Bedienungsanleitung

Epson

Epson PowerLite Pro Z8000WUNL Bedienungsanleitung

Epson

Epson 6100i - PowerLite XGA LCD Projector Technisches Datenblatt

Epson

Epson EMP-830 Bedienungsanleitung

Epson

Epson EasyMP.net Network Option Board Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung

JVC

JVC 1108TTH-AO-AO Bedienungsanleitung