EPV Marquee Tension Series Bedienungsanleitung

02142023JA 1 www.epvscreens.com

Marquee Tension Series

In-Ceiling Electric Tab-Tensioned Projection Screen

Installation Guide

H Type (RC1)

Visit www.epvscreens.com for the latest updated version

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

In order for the screen material to maintain its projection qualities and optimum performance, please refer to the list

below for proper maintenance and cleaning.

•Use a dry microfiber cloth to remove dust from the screen’s surface.

•When cleaning, use a damp microfiber cloth with warm water to remove any marks.

•Never rub or apply pressure when cleaning the surface.

•Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.

•To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other sharp

or abrasive objects.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top

Drop in the roller. Unapproved changes or modifications (except for cutting the power cord for hardwire

installations) to this unit are prohibited and will void your warranty. For more information, please contact our

Technical Support Department at techsupport@epvscreens.com

•Please retain this user’s guide for future reference.

•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

•Handle the unit carefully during transportation to avoid any damages.

•To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.

•The power outlet supplying power to the unit should be close to the unit and easily accessible.

•Do not install the unit on uneven, inclined surfaces.

•Do not install in damp places to avoid an electric shock or short circuit.

•Do not place any heavy objects over the power cord.

•Position the power cord properly to avoid creating a trip obstacle.

•To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the power cord.

•The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble this unit

by yourself. No one except authorized technicians can open and make repairs to this unit.

•Make sure the power source that this unit is connected to has a continuous power flow.

•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to avoid

overheat.

•Do not handle the power plug when your hands are wet or your feet are in contact with water.

•Properly dispose of this equipment according to the environmental regulations in your area when product is no

longer of service.

02142023JA 2 www.epvscreens.com

Do not use this unit under the following circumstances.

•Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.

•Avoid direct sun light, rain shower and moisture.

•Keep away from fire sources and high temperature to prevent this device from overheating.

•Cut off the power supply first before transportation or maintenance.

•To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious damage

or if there are any evident broken parts.

Installation Warning

The instructions provided in this user’s guide are for reference only. Please consult a professional installation

company for further installation and safety advice. The installer must insurethat proper mounting hardware

is used to provide adequate strength suitable for the installation. EPV is not liable for any faulty installations.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this equipment

causes harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

✓Reorient or relocate the receiving antenna of the device which may be casing the interference.

✓Increase the separation between the screen and the device’s receiver.

✓Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles

such as dust, sawdust, and/or liquids.

Screen operation

Electric Current: The screen operates on AC110V at 60Hz/ 0.77A / 85W

1.After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.

2. Once the screen has power, you’ll be able to control it using any of the 5 methods described below.

Polar Max Recessed | Controls and Accessories

A. IR Remote

ZRC1-IR

B. RF Remote

ZRC1-RF

C. Wall box

controller

ZRC1-WB

D. RJ50 cable

ZRC1-RJ50

G. AAA

batteries

H. Bubble

leveler

02142023JA 3 www.epvscreens.com

5 Ways to control your screen

1. IR Remote control (Item A, Fig 1): The Infrared functions by direct line of

sight contact using an effective beam range of 25 feet within a 30-degree angle.

Aim the IR remote directly at the Wall Box Controller to operate the screen.

Note: Assure there is no obstruction between the IR remote and IR receiver.

2. RF Remote Control (Item B): The radio waves eliminate the need for a direct

line of sight and has a longer distance control range.

The RF remote is already pre-synced/paired and ready to use. If

synchronization/ pairing is needed, please follow the steps below.

How to synchronize/pair a new RF remote:

•Press & hold the “Programming Key”, then press the “Up Key” on the Wall box controller (wall-box LED

flashes). Reference the wall box controller section for programming key location.

•Then press the “Up Key” on the RF remote.

•The Wall box LED will flash 5 times, to indicate the RF remote has been properly synchronized/paired.

How to change the RF code (For use when multiple screens/RF remotes are owned)

Changing the RF code avoids controlling multiple screens at the same time and prevents electrical interference leading

to accidental control of the screen.

1. Remove the batteries

2. Change the RF code switch

3. Insert the batteries

4. Synchronize it with the wall box controller

3. Wall box controller (Item C, Fig 2): The wall box controller switch is a wall mounted control box with an

up/stop/down button. It plugs directly into the screen’s RJ50 port located on the circuit board box.

LED

light

STOP

DOWN

Fig.1

IR/RF remote

IR Lens

(IR remote only)

Wall box controller

SIDE VIEW

RJ50 PORT:

Connects to the

Screen RJ50

PORT (RJ50

CABLE ONLY)

3.5mm mono Projector

Trigger Port (if

Projector equipped)

Wall box

controller BACK

VIEW

Programming

Key

Fig.2

Wall box controller

IR Receiver

RJ50 cable

Circuit board box

Battery compartment

Default

“000”

RF Remote

BACK

VIEW

Slide

Switches

for RF Code

change

02142023JA 4 www.epvscreens.com

4.Wired 5-12 volt trigger (Fig. 3): Requires a 3.5mm to 3.5mm mono cable (not included)

Step 1: Connect one end of the RJ50 cable to the screen and the other end

to the Wall box controller.

Step 2: Then connect one end of the 3.5mm mono cable to the wall box

controller and the other to the projector.

Once the two cables have been connected, the wired trigger

feature is ready to synchronize the screen’s up/down

operation with the projector’s power cycle.

•Projector on, screen drops

•Projector off, screen raises

5. Wireless 5-12 volt trigger (Fig 4): Requires a 3.5mm to 3.5mm mono cable (not included).

The Radio Frequency (RF) remote control serves as a dual purpose, independently as a handheld remote control, or as

a Wireless 5-12 volt trigger. The radio frequency technology sends a wireless signal that synchronizes the screen’s

drop & rise with the projector’s power cycle.

Here’s how to set up your Wireless 5-12 volt trigger

The 5-12V wireless trigger should already be synced and ready to work.

Step1: Connect one end of the 3.5 mm mono trigger cable to the RF remote.

Step 2: Connect the other 3.5 mm mono end of the cable to your projector

Step 3: Turn on the projector and the screen should automatically deploy.

Step 4: Turn off your projector and the screen should automatically retract.

(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20- 30seconds

for full off and on cycle each time)

Note: If the wireless trigger feature does not work, please resync the RF remote to the Wall box controller per the

instructions in the Radio Frequency remote section.

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

Wall box controller

Fig. 3

RJ50 cable

Projector

Fig 4

3.5 mm port

DC 5-12V out

3.5mm to 3.5mm mono cable

STOP

DOWN

Projector

Mono 3.5mm

Projector Trigger

Port

RF remote

control

SIDE VIEW

02142023JA 5 www.epvscreens.com

ADVANCED Programming Key Instructions: (FOR ADVANCED USERS ONLY)

Wall box controller must be connected to the screen.

1. Preset the Screen’s Drop Position:

Use the RF/IR remote or Wall Box Controller to Drop the screen to the desired position you want to set it at.

Press & hold the “Programming Key”, then press the “Down key” on the Wall Box Controller. The LED will flash 5

times to confirm new programmed drop position.

2. Clear/Reset the Screen’s Drop Position to factory default:

Press & hold the “Programming Key + “Stop key” on the wall box controller.

Installation Instructions

The Marquee Tension allows access for above or below ceiling installation. Please follow the instructions described

in the following steps below for your type of installation.

Power

The Marquee Tension includes a 3-Prong Power Cord (2-Prong Power Cord for some countries) for use in a non-

concealed power outlet. If your installation will be entirely concealed (including power outlet), EPV strongly

recommends a hardwire connection. Please refer to the image below for both 110v & 220v wiring information.

ATTENTION: Reducing the factory’s full screen drop may produce waves/wrinkles on the projection surface on

tab-tension screens. The full drop is recommended to allow the screen to rely on the tab-tension system to

maintain the projection surface flat and taut on all sides.

The same applies on non-tensioned screens, although some level of waves may be present due to the nature of

the screen not being tensioned. If wrinkles/waves develop after making the adjustment to the desired drop

position, reset it to the factory’s default position per the instructions below.

PROGAMMING NOTE:

The programmed vertical drop position will have +/- 2" tolerance, which will depend on the temperature of the

installed screen environment.

02142023JA 6 www.epvscreens.com

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the

viewing surface will not cause the casing to become loose or fall. The installer must ensure the fasteners that are used

are of adequate strength and suitable for the installation location.

Hardware Parts List for Marquee Tension Series

Please make sure all parts listed below are included before proceeding with the installation.

Hardware Parts List for above ceiling installation

A. Suspension Bracket x 2

B. Suspension Bar x 4

C. End Flange x 2

C. M8x16mmx1.5mm washer x 8

D. M6x13mmx2mm washer x 8

E. M8 nut x 4

F. M6 nut x 4

G. M8x40mm hex screw x 4

H.M6x20mm screw x 4

A. Above ceiling installation instructions

Assembly

1. Place the hanging bracket (A) over the left and right side ends of the housing and secure each one using

the M8x40mmhex screw (G), M8x16mmx1.5mm washers (C) and M8 nut (E) as shown below.

Hanging Bracket

02142023JA 7 www.epvscreens.com

2. Place the Suspension Bar (B) over the Hanging Bracket (A) and align with the hole as shown below

according to the height requirement for your installation area. Secure the Suspension Bar (B) with the

M6x20mmScrew (B), M6x13mmx2mmWasher (E) and the M6 Nut (F). Repeat the process for the other

side.

3. Insert the end flange piece (C) on the edge of the housing as shown below to complete the assembly.

The screen is now ready for installation.

B. Below ceiling installation instructions

Please make sure all parts listed below are included before proceeding with the installation.

Hardware Parts List for below ceiling installation

A. End Flange x 2

B. Hanging bracket x 2

C. Threaded rod x 4

D. Socket wrench x 1

E. M8x16mm x 1.5mm

washer x 28

F. M8 nut x 20

G.M8 Top expanding bolt x 4

H. M8x40mm hex screw x 4

Push end flange piece into

housing end until it snaps in

02142023JA 8 www.epvscreens.com

Install screw holes

1. Measure and cut the ceiling installation slot:

The width should not exceed 3.93” (100mm) and not less than the width of the screen’s housing.

Measure the length of your screen to determine the length.

2. Drill 4 holes in the ceiling that correspond with the attachments on the various casing sizes. The width

should be 120mm. The length of (A5) in the diagram below depicts the distance between the holes

located on each ear end of the screen’s case.

The ceiling wall

3. The M8expanding bolts (G) mount into thick wood beams, stone or concrete and will support the

screen. Use the Socket wrench (D) to attach the M8x40mm hexagonal screws. The expanding bolts

should be firmly tightened and tested to make sure that they will hold the weight of the screen.

Ceiling

Truss

Ceiling

Screen installation slot

3.93” (100 mm)

02142023JA 9 www.epvscreens.com

4. Insert the threaded rods (C) through the M8 expanding bolts and then attach the M8x40mm

hexagonal screws with the washer (E). Last put the Hanging Bracket (B) through the threaded rod

equal to the height of the screen’s housing. Once they are firmly in place (as shown below) make sure

that they will hold the weight of the screen.

5. Push the screen up into the space. Use the threaded rods (C) to attach the screen assembly to the ceiling.

The hexagonal screws (E) will connect the screen to the rest of the assembly. Once firmly in place; use the

nuts (F) to ensure a firm connection. Use the socket wrench (D) to make sure that the bolts are firmly

tightened.

6. Install end flange cover panel (A) between the gap and the screen to complete the installation.

For local EPV contact or Technical Support, please visit

www.epvscreens.com

Inhaltsverzeichnis

Andere EPV Projektionsfläche Handbücher

EPV

EPV Prime Vision ISF Series Bedienungsanleitung

EPV

EPV Twilight Portable Series Bedienungsanleitung

EPV

EPV Power Max Tension ISF Series Bedienungsanleitung

EPV

EPV Dark Star UST 2 eFinity Series Bedienungsanleitung

EPV

EPV Power Max Sonic 2 Series Bedienungsanleitung

EPV

EPV Sonic AT8 ISF Series Bedienungsanleitung

EPV

EPV Twilight Portable Series Bedienungsanleitung

EPV

EPV Efinity Edge Free Series Bedienungsanleitung

EPV

EPV Polar Star eFinity Series Bedienungsanleitung

EPV

EPV Dark Star UST eFinity Series Bedienungsanleitung

EPV

EPV PMX92HT2-E12 Bedienungsanleitung

EPV

EPV PowerMax Series Bedienungsanleitung

EPV

EPV Peregrine ISF Series Bedienungsanleitung

EPV

EPV DarkStar UST eFinity Series Bedienungsanleitung

EPV

EPV Twilight Portable Series Bedienungsanleitung

EPV

EPV Polar Star eFinity 2 Series Bedienungsanleitung

EPV

EPV Prime Vision ISF Series Bedienungsanleitung

EPV

EPV PowerMax Tension Series Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung