Equinox Systems RGB 1.5M DMX Bedienungsanleitung

USER MANUAL

RGB 1.5M DMX Flame Machine

Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to flammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature fluctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

Overview

You should find inside the carton the following items:

1, RGB 1.5M DMX Flame machine 2, User manual 3, Power cable

Operation:

To activate the unit, first connect the IEC cable into the unit and then connect the plug into a AC 240V

power supply. Once the unit has been connected use the “POWER SWITCH” located next the “POWER

IEC” input socket to turn the unit ON or OFF.

Overview:

Operating Instructions

The RGB 1.5M Flame Machine is a DMX-512 controllable, full RGB colour mixing Flame Machine made

up of high efficiency and super bright LED’s. There are three colour groups (red, blue and green) whose

intensity can be controlled individually allowing the creation of an unlimited range of colours.

The RGB 1.5M DMX Flame Machine will operate in stand-alone, master/slave, sound activated and

DMX-512 control.

Control features:

• 6 channel DMX-512

• Static/Dimmer/Strobe

• Individual control of Red, Green and Blue LEDs

Features

• 168 LEDs: - Red (60), Green (54), and Blue (54)

• Ultra Bright 10mm LEDs

• RGB colour mixing

• Built-in colour change programmes

• Power consumption: 130W

• Master/Slave mode

• Programmable from Any universal DMX-512 controller

DMX Channel Summary

Introduction

Operation modes

Strobe Mode

To set the unit in strobe mode, set dip switch 1 to ON and all others to the OFF position. Now use the

sensitivity control to adjust the speed.

Fade mode

To set the unit in fade mode, set dip switch 2 to ON and all others to the OFF position. Now use the

sensitivity control to adjust the speed.

7 Colour Chase mode

To set the unit in 7 colour chase mode, set dip switch 3 to ON and all others to the OFF

position. Now use the sensitivity control to adjust the speed.

5 Colour Chase mode

To set the unit in 5 colour chase mode, set dip switch 4 to ON and all others to the OFF

position. Now use the sensitivity control to adjust the speed.

Red and Green Colour Chase Mode

To set the unit in red and green colour chase mode, set dip switch 5 to ON and all others to the OFF

position. Now use the sensitivity control to adjust the speed.

Static Colour Selection

To select a static colour, use any of the dip switches listed below;

Dip switch 6set to ON, obtains static Red

Dip switch 7set to ON, obtains static Green

Dip switch 8set to ON, obtains static Blue

Now use the sensitivity control to adjust the brightness.

Note: You can have any combination of switches 6, 7 and 8 to obtain further mix colours.

Sound Activation

The RGB Flame machine has a built-in microphone which enables it to operate in Sound to Light mode.

Set the sensitivity control to the desired level, and the RGB Flame machine will change colour to the

beat of the music. Set dip switch 9 to ON and all others to the OFF position to activate Sound Mode.

Master/Slave mode

Use any of the above modes to set the master unit. To set the unit(s) in slave mode set dip switch 10 to

the ON position and all others to OFF.

Note: When all of the dip switches are set to OFF, the unit will automatically run in a RGB colour

chase. Use the sensitivity control to adjust the speed.

Operation

Daisy Chain Connection

1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin

connector of the first fixture

2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector.

Proceed to connect from the output as stated above to the input of the following fixture

and so on.

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of the

fixture and each fixture independently. The Equinox RGB 1.5M DMX Flame Machine uses 6 channels of

control.

Enable the DMX control by setting dip switch No: 10 to the ON position. Use dip switches 1 – 9 to

address each fixture accordingly.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start address”

from 1- 511. A fixture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105 and

106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the chain

starts at 107.

Input from DMX controller

Use 3-pin XLR DMX cable Use 3-pin XLR DMX cable

Control options

DMX Values

Technical Specifications

Weight & Dimensions

• Length …....................................................... .............................................................................. 512mm

• Width .................................................................. ......................................................................... 240mm

• Height ……………………………………?…............................................................................. 330mm

• Weight ………………………………………..... ............................................................................... 9.7kgs

Power

• Input ……………………………………...................................................................................... 240V/50hz

Control & Programming

• Data input ………………………………………..................................... Locking 3-pin XLR male socket

• Data output ……………………………………................................... Locking 3-pin XLR female socket

• Protocols ……………………………………..................................................................... DMX-512 USITT

• DMX channels …………………………………. ....................................................................................... 6

Inhaltsverzeichnis

Andere Equinox Systems Leuchte Handbücher

Equinox Systems

Equinox Systems Fusion 120 Zoom Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED069A Bedienungsanleitung

Equinox Systems

Equinox Systems Blitzer II Bedienungsanleitung

Equinox Systems

Equinox Systems Promo Spot EQLED86 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED068A Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT MKIII Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung