Equinox Systems Domin8r IIEQLED53 Bedienungsanleitung

Order code: EQLED53

User manual

www.prolight.co.uk

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

Equinox Domin8R 2 Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Cleaning must be done at regular intervals.

• Before cleaning, wait until the unit has cooled.

• Use a vacuum or dry compressed air and a soft brush to remove the dust collected on the

external vents and accessible internal components.

• Clean the external surfaces with a mild solution of non-ammonia glass cleaner or

isopropyl alcohol and wipe with a soft, lint free cotton cloth or lense cleaning tissue.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 100V/240V.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

LED failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

You should nd inside the Equinox carton the following items:

1, Equinox Domin8R 2 2, Power cable 3, Instruction manual

Technical Specications:

DMX channels: 8 or 16 selectable

120 x 5mm LEDs (R: 40, G: 40, B: 40)

Sound active, auto, master/slave and DMX modes

IEC power in/out sockets

3-pin XLR in/out sockets

4 push button menu with LED display

Robust metal housing

Convection cooled

Power supply: 100-240V~50/60Hz

Fuse: 3 Amp

Power consumption: 90W

Dimensions: 906 x 112 x 317mm

Weight: 10.4Kgs

Overview:

Equinox Domin8R 2 Technical specications

Identication:

1. Hanging bracket

2. IEC power in/out socket

3. Earth screw

4. DMX output socket

5. DMX input socket

6. Sensitivity control

7. LED display

8. Function buttons

9. Hanging bracket tightening knobs

10. Safety eye

11. Microphone

Equinox Domin8R 2 Operation

Operation modes:

DMX mode:

To select DMX mode, press the “MENU” button to show “ADDR” on the display. Now press the

“ENTER” button and use the “UP” and “DOWN” buttons to set the DMX address from 001-512. When

you have nished setting the desired DMX address press the “ENTER” button.

For DMX functions, please refer to the DMX function chart overleaf.

DMX channel mode:

To choose one of the DMX channel modes, press the “MENU” button to show “CHND” on the display.

Now press the “ENTER” button and use the “UP” and “DOWN” button to choose the 8 or 16 DMX

channel mode. To conrm your choice, press the “ENTER” button.

Master/slave mode

To select the slave mode, press the “MENU” button to show “SLND” on the LED display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select either

“MAST”, “SLA1” or “SLA2”.

“MAST” option: This is the master setting mode, where you can set the rst unit as a master.

“SL-1” option: This is the normal slave mode, where the slave units all do the same thing

following the master unit.

“SL-2” option: This is the inversion slave mode, where the slave unit(s) will react in the opposite

direction from the master unit.

Sound active mode:

To select sound active mode, press the “MENU” button to show “SOUN” on the LED display.

Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the sound active

mode “ON” or “OFF”. The unit will now react to the beat of the music.

Note: When there is no music present the unit will automatically switch to slow auto run.

LED mode

Use this mode to turn the LED display ON or OFF. To do this, press the “MENU” button to show “LED”

on the display. Now use the the “UP” and “DOWN” buttons to select either “ON” or “OFF”.

Display mode

In this mode you can ip the display over to match which way the unit is being used. To ip the display,

press the “MENU” button to show “DISP” on the display. Now press the “ENTER” button to ip the

display over and again to ip it back to its original position.

Test mode

In this mode you can test that all of the LEDs are illuminating. To do this, press the “MENU” button to

show “TEST” on the display. Now press the “ENTER” button to initiate the test. Once you are happy

with the test, press the “ENTER” button to stop it.

Hour mode (non re-settable)

In this mode you can check the total time the unit has been used for. To check the units time line, press

the “MENU” button to show “HOUR” on the display. Now press the “ENTER” button to display the units

time usage. For example if the unit has been in use for 5 hours the display will show

“- - - 5”. If the unit has been in use for 120 hours the display will show “-120” and so on.

Equinox Domin8R 2 DMX Charts

8 channel DMX chart:

CHANNEL

VALUE

0-127

128-255

0-255

0-127

128-255

0-255

0-127

128-255

0-255

FUNCTION

No function

Strobe (slow to fast)

Static pattern selector

Moving pattern selector

Static pattern

Moving pattern

Moving pattern speed (slow to fast)

Manual mirror tilt

Auto mirror tilt (up and down)

Mirror tilt speed

Equinox Domin8R 2 DMX Charts

16 channel DMX chart:

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT” XLR

terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together and

operate from a single controller, as long as all xtures and the controller are DMX compliant. To ensure

proper DMX data transmission, when using several DMX xtures try to use the shortest cable path pos-

sible. The order in which xtures are connected in a DMX line does not inuence the DMX addressing.

For example; a xture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the

beginning, at the end, or anywhere in the middle. When a xture is assigned a DMX address of 1, the

DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in

the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Equinox Domin8R 2 can be controlled via DMX-512 protocol. The DMX address is set on the back

of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data input/

output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

Further DMX cables can be purchased from

all good sound and lighting suppliers or

Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Equinox Domin8R 2 DMX Set up

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing.

Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90 3-pin, CABL89 5-pin) will decrease the

possibilities of erratic behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

Equinox Domin8R 2 DMX Set up

Notes:

Equinox Domin8R 2 Notes

Inhaltsverzeichnis

Andere Equinox Systems Beleuchtungsausrüstung Handbücher

Equinox Systems

Equinox Systems QUADZILLA Bedienungsanleitung

Equinox Systems

Equinox Systems Vortex Bedienungsanleitung

Equinox Systems

Equinox Systems FUSION SPOT MAX MKII Bedienungsanleitung

Equinox Systems

Equinox Systems GEMINI Bedienungsanleitung

Equinox Systems

Equinox Systems Swing Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Party Par EQLED015 Bedienungsanleitung

Equinox Systems

Equinox Systems ARIES EQLA20 Bedienungsanleitung

Equinox Systems

Equinox Systems Explo Strobe EX-2500 Bedienungsanleitung

Equinox Systems

Equinox Systems Nova Par 64 Bedienungsanleitung

Equinox Systems

Equinox Systems MaxiPar Tri Bedienungsanleitung

Equinox Systems

Equinox Systems XP 80W Bedienungsanleitung

Equinox Systems

Equinox Systems CAPRICORN EQLA22 Bedienungsanleitung

Equinox Systems

Equinox Systems QUADRILLE Bedienungsanleitung

Equinox Systems

Equinox Systems Terminator 2 Bedienungsanleitung

Equinox Systems

Equinox Systems Lighting strike STRO21 Bedienungsanleitung

Equinox Systems

Equinox Systems Megabar System EQLED63 Bedienungsanleitung

Equinox Systems

Equinox Systems EQLED040 Bedienungsanleitung

Equinox Systems

Equinox Systems 400W UV Cannon Bedienungsanleitung

Equinox Systems

Equinox Systems PIXELpoint Batten Bedienungsanleitung

Equinox Systems

Equinox Systems Fusion 260ZR Bedienungsanleitung

Equinox Systems

Equinox Systems Nimbus Bedienungsanleitung

Equinox Systems

Equinox Systems SF-300 Bedienungsanleitung

Equinox Systems

Equinox Systems Cirrus Bedienungsanleitung

Equinox Systems

Equinox Systems COBALT Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung