Erickson 07464 Bedienungsanleitung
Item No. 07464
English/French/Spanish Page 1 of 4
80” x 11” STEEL MESH LOADING RAMP
WARNING:
To avoid personal injury and/or property damage, please read and
follow ALL of these instructions before assembling and operating.
1. Never overload ramps. Maximum capacity for your ramp is 800 lbs per ramp; 1600
lbs per pair (all loads must be evenly distributed).
2. Always use safety strap to securely fasten the ramp to the vehicle. This prevents the
ramp from slipping off of the tailgate.
3. Carefully roll or winch equipment up or down the ramp. Never drive or ride your
equipment while loading or unloading.
4. Make sure the ramp is aligned with the wheels of the equipment being loaded or
unloaded.
5. Always load or unload on a solid, level and stable surface with the vehicle in park, the
parking/emergency brake on and the engine off.
6. Use as loading ramp only.
7. Ramp surfaces must be clean, dry and free from oil or grease or water.
8. Maximum recommended height is 30 inches.
9. Inspect ramp before each use. Tighten any loose hardware. Replace any worn or
damaged parts. Replace safety strap if webbing is frayed or worn. Do not attempt
to use a ramp that is damaged in any way. No modication, alteration or deviation to
the ramp are authorized by the manufacturer and shall not be made. Proper care and
maintenance of the ramp is essential to safety.
10. Proper use of this product is critical to safety and beyond the control of Erickson
Manufacturing Ltd. Erickson Manufacturing Ltd. neither guarantees nor is liable for
any damage resulting from improper use. The liability of this product is limited to its
purchase price if it proves to be defective in material and/or workmanship. Warranty
information is available upon request.
Item No. 07464
English/French/Spanish Page 2 of 4
SPECIFICATIONS
Rated Capacity 800 lbs. distributed load and
1600 lbs when using 2 ramps
Ramp dimensions
(Unfolded) 80” long x 11” wide
Ramp dimensions
(Folded) 40” x 11” x 41/8”
USAGE
Step 1
Be sure you are loading on a hard, level and stable surface and that the vehicle you
are loading onto is in “Park” with the emergency/parking brake on and the engine “off”.
Unfold and place the lip edge of the ramp against the tailgate of the vehicle. The tailgate
should not be more than 30” in height or the ramp incline will be to steep.
Step 2
Secure the ramp to the vehicle using the adjustable strap. After the strap is secure, test
the ramp by pulling backwards on it. Make sure it does not slide back or disengage from
the loading surface.
Step 3
Once the ramp is secure and the area is safe to proceed with loading, move the vehicle
to be loaded between the ramps and center the load between both ramp rails.
Step 4
Proceed with loading the vehicle, making sure that the ramp is sustaining the load and
not bowing from the weight.
Step 5
Continue until the vehicle is fully loaded. Secure the brake and tie down as needed.
Step 6
Unhook the adjustable strap, fold the ramp and lock into the folded position. Store in a
clean, dry and safe place where damage will not occur.
Item No. 07464
English/French/Spanish Page 3 of 4
Strap must be tight
1 YEAR LIMITED WARRANTY
Warranty Qualications
Effective from the day you purchase this product. Please keep your original invoice as
proof of purchase.
Repair/Replacement Warranty
Erickson Manufacturing Ltd. warrants to the original purchaser that the mechanical com-
ponents will be free of defects in material and workmanship for 1 year from the original
date of purchase (90 days for commercial and industrial use). Transportation charges on
product submitted for repair or replacement under this warranty are sole responsibility of
the purchaser. This warranty only applies to the original purchaser and is not transfer-
able.
DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE
Contact Erickson Manufacturing Ltd.’s Technical Service Department and service rep-
resentatives will troubleshoot any issue via phone or e-mail. Repairs and replacements
without prior authorization, or at an unauthorized repair facility will not be covered by this
warranty.
Item No. 07464
English/French/Spanish Page 4 of 4
Warranty Exclusions
This warranty does not cover the following repairs and equipment.
Normal Wear
This warranty does not cover repair when normal use has exhausted the life of a part or
the equipment as a whole.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labor if this product is deemed to have been
misused, neglected, involved in an accident, abused, loaded beyond the specications,
modied, or installed improperly. Normal maintenance is not covered by this warranty.
Other Exclusions
This warranty excludes:
• Cosmetic defects such as paint, decals, etc.
• Wear items
• Accessory parts
• Failures due to acts of God and other major events beyond the manufacturer’s
control
• Problems caused by parts that are not original Erickson Manufacturing Ltd. parts
Limits of Implied Warranty and Consequential Damage
Erickson Manufacturing Ltd. disclaims any obligation to cover any loss of time, use of
this product, freight, or any incidental or consequential claim by anyone from using this
product. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. A unit provided as exchange will be subject to the warranty
of the original unit. The length of the warranty governing the exchanged unit will remain
calculated by reference to the purchase date of the original unit. This warranty gives you
certain legal rights which may change from state to state. Your state may also have other
rights you may be entitled to that are not listed within this warranty.
Contact Information:
Marine City, Michigan 48039
Thamesville, Ontario N0P 2K0
Toll Free: 1-888-546-4668
Inhaltsverzeichnis
Andere Erickson Hebesystem Handbücher
Beliebte Hebesystem Handbücher anderer Marken
morse
morse 82H-124 Bedienungsanleitung
Braun
Braun NL955 Series Bedienungsanleitung
haacon
haacon 1889.10 Bedienungsanleitung
Protekt
Protekt AT 252 Bedienungsanleitung
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Bedienungsanleitung
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Bedienungsanleitung
Genie
Genie Z-60/34 Bedienungsanleitung
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Bedienungsanleitung
Custom Equipment
Custom Equipment Hy-Brid 3 Series Programmierhandbuch
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Programmierhandbuch
