Ericsson MINI-LINK 6351 Bedienungsanleitung

Installing a MINI-LINK 6351

INSTALLATION INSTRUCTIONS

13/1531-HRA 901 17/9 Uen B

reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to

continued progress in methodology, design and manufacturing. Ericsson shall

have no liability for any error or damage of any kind resulting from the use

of this document.

13/1531-HRA 901 17/9 Uen B | 2016-03-04

Contents

1 Overview of Installing a MINI-LINK 6351 1

2 Safety Information 3

3 Preparing for Installation 5

3.1 Power Supply Requirements 5

3.2 Temperature Requirements 5

3.3 Required HW Tools 5

3.4 Required Units and Accessories 8

3.5 Installing the MINI-LINK Alignment App 11

4 Installing the RMM 13

5 Installing the MINI-LINK 6351 17

5.1 Assembling the MINI-LINK 6351 17

5.2 Installing the MINI-LINK 6351 on a Wall 19

5.3 Installing the MINI-LINK 6351 in a Mast 22

5.4 Installing PoE Equipment and Cable 26

6 Performing an Initial Setup 41

7 Aligning the Antenna 43

7.1 Preparing for Antenna Alignment 43

7.2 Aligning the Antenna Using the Alignment Camera 43

7.3 Optimizing the Antenna Alignment 52

Reference List 57

13/1531-HRA 901 17/9 Uen B | 2016-03-04

Installing a MINI-LINK 6351

13/1531-HRA 901 17/9 Uen B | 2016-03-04

Overview of Installing a MINI-LINK 6351

1 Overview of Installing a MINI-LINK 6351

A MINI-LINK 6351 can be installed on a wall or in a mast. Traffic and power are

provided through a single cable using Power over Ethernet (PoE).

Note: If you configure the packet radio using a script on the RMM, and that

script turns on the transmitter, do not connect the packet radio to power

until after mounting the packet radio and aligning it visually.

PoE cable

Packet radio

PoE injector

Power cable

Ethernet cable

Figure 1 System Overview

Connectors

All connectors are at the back of the MINI-LINK 6351.

13/1531-HRA 901 17/9 Uen B | 2016-03-04

Installing a MINI-LINK 6351

Figure 2 Connectors on MINI-LINK 6351

Table 1 Connectors

Item Connector

1EARTH

2PoE

3O&M and ALIGNMENT

213/1531-HRA 901 17/9 Uen B | 2016-03-04

Safety Information

2 Safety Information

Make sure that the information in the following documents has been understood

by the persons performing the procedures:

•Personal Health and Safety Information, Reference [1]

•System Safety Information, Reference [3]

•Supplementary Safety Information for MINI-LINK, Reference [2]

13/1531-HRA 901 17/9 Uen B | 2016-03-04

Installing a MINI-LINK 6351

413/1531-HRA 901 17/9 Uen B | 2016-03-04

Preparing for Installation

3 Preparing for Installation

This section contains information on tools and equipment necessary for the

outdoor installation. It also gives an overview of units and accessories.

3.1 Power Supply Requirements

MINI-LINK 6351 has a IEEE 802.3at compatible PoE interface. The chassis is

connected to the cable shield.

For more information, see Technical Description.

3.2 Temperature Requirements

The equipment operates according to the following constraints:

• Continuous Conditions (Normal Operation)

Temperature:



C to +55



F to +131



Measure outdoor temperature in an open, unshielded area, preferably

close to the radio. The sensor must be protected from the sun.

Minimum distance to other objects is 50 cm.

Relative Humidity: 8–100%

• Exceptional Conditions (Safe Function)

Temperature:



C to +60



F to +140



Measure outdoor temperature in an open, unshielded area, preferably

close to the radio. The sensor must be protected from the sun.

Minimum distance to other objects is 50 cm.

3.3 Required HW Tools

3.3.1 Outdoor Installation

Table 2 Tools

Tool Dimension or type

Metric combination wrench 10 mm, 13 mm, and 16 mm

Hex key 2.5 mm (M3) and 4 mm (M4)

513/1531-HRA 901 17/9 Uen B | 2016-03-04

Installing a MINI-LINK 6351

Tool Dimension or type

Extended T-handle 6 mm hex key LSB 903 36

Torx screwdriver TX 10 (M3), TX 20 (M4), and TX 25

(M5)

Torque wrench 13 mm, and 16 mm

Torque wrench with socket 13 mm, 16 mm, and 18 mm

Torque wrench with hex insert 5 mm and 6 mm

Digital multimeter with standard test

probes (2 mm diameter)

Lubricating substance For example: Molykote DX(1)

For outdoor screws and nuts

(1) Manufacturer: Molykote, Dow Corning GmbH, Pelkovenstrasse 152, D-8000 Munich 50,

Germany

LSB 903 36

8650

Figure 3 Extended T-handle Hex Key

3.3.2 Outdoor Cabling

Table 3 Tools

Tool Dimension or type

Hex key 4 mm (M4)

Torque wrench with socket 16 mm and 18 mm

Torque wrench with hex insert 6mm

Cable clamp pliers LSD 349 20(1)

Cable jacket cutter LTX 102 17

Knife

Cutting pliers

Digital multimeter with standard test

probes (2 mm diameter)

(1) Only required if metal straps are used when clamping the cables

613/1531-HRA 901 17/9 Uen B | 2016-03-04

Andere Handbücher für MINI-LINK 6351

Inhaltsverzeichnis

Andere Ericsson Antenne Handbücher

Ericsson

Ericsson AIR 21 Montageanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch