Ericsson LBI-39012A Bedienungsanleitung

LBI-39012A

Mobile Communications

MDXTM CONVENTIONAL

MOBILE RADIO

Operator’s Manual

TABLE OF CONTENTS

Page

SAFETYINFORMATION . . . . . . . . . . . . . . . 4

SAFE DRIVING RECOMMENDATIONS FOR USERS OF

MOBILE RADIOS* . . . . . . . . . . . . . . . . . . 5

OPERATING PROCEDURES . . . . . . . . . . . . . 5

INTRODUCTION . . . . . . . . . . . . . . . . . . . 6

CONTROLS, INDICATORS, AND DISPLAYS . . . . 7

CONTROLS . . . . . . . . . . . . . . . . . . . . 7

CONTROLS AND INDICATORS . . . . . . . . 8

DISPLAY INDICATORS . . . . . . . . . . . . . 10

DISPLAYALPHAINDICATORS . . . . . . . . . 11

OPERATING THE RADIO . . . . . . . . . . . . 12

TURNING THE RADIO ON . . . . . . . . . . . 12

SELECT . . . . . . . . . . . . . . . . . . . . . . 13

CONVENTIONAL MODE OPERATION . . . . . . . 13

RECEIVING ACALL . . . . . . . . . . . . . . . 13

SENDING AMESSAGE . . . . . . . . . . . . . 13

TALK-AROUND . . . . . . . . . . . . . . . . . 14

SCAN OPERATION . . . . . . . . . . . . . . . . . . 14

SCAN SETUP . . . . . . . . . . . . . . . . . . . 14

STARTING OR STOPPING SCAN . . . . . . . . 14

TABLE OFCONTENTS (CONTINUED)

Page

ADDING/DELETING TO/FROM SCAN . . . . 14

RECEIVER SCAN RATE . . . . . . . . . . . . 15

USING THE RADIO WITH SCAN . . . . . . . 16

OPTIONS . . . . . . . . . . . . . . . . . . . . . . . 21

AVAILABLE OPTIONS . . . . . . . . . . . . . . . . 22

OPERATING TIPS . . . . . . . . . . . . . . . . . . . Back Cover

SAFETY INFORMATION

The operator of any mobile radio should be aware of certain hazards

common to the operation of vehicular radio transmissions.

Alist of possible hazards are:

1. ExplosiveAtmospheres

Just as it is dangerous to fuel a vehicle with the motor running, be

sure to turn the radio off while fueling the vehicle. Do not carry

containers of fuel in the trunk.

2. Interference to Vehicular Electronics Systems

Electronic fuel injection systems, electronic anti skid braking sys-

tems, etc., are typical of the type of electronic devices that may

malfunctionduetothelackofprotectionfromradiofrequencyenergy

present when transmitting. If the vehicle contains such equipment,

consult the dealer for the make of the vehicle and enlist his aid in

determining if such electronic circuits perform normally when the

radio is transmitting.

3. Dynamite Blasting Caps

Dynamiteblastingcapsmaybecausedtoexplodebyoperatingaradio

within500feetof theblastingcaps.Alwaysobeythe"TurnOffTwo

Way Radios" signs posted where dynamite is being used. When

transporting blasting caps in your vehicle:

a. Carry the blasting caps in a closed metal box with a soft lining.

b. Leave the radio OFF whenever the blasting caps are being put

into or removed from the vehicle.

4. Radio Frequency Energy

To prevent burns or related physical injury from radio frequency

energy, do not operate the transmitter when anyone outside of the

vehicle is within two feet of the antenna.

5. Liquefied (LP) Gas Powered Vehicles

Mobileradioinstallationsinvehiclespoweredbyliquefiedpetroleum

gas with the LP gas container in the trunk or other sealed-off space

within the interior of the vehicle must conform to the National Fire

Protection Association standard (NEPA) 58 which requires that:

a. The space containing the radio equipment shall be isolated by a

seal from the space containing the LP gas container and its

fittings.

b. OutsidefillingconnectionsshallbeusedfortheLPgascontainer.

c. The LPgascontainershallbeventedtotheoutsideof thevehicle.

SAFE DRIVING RECOMMENDATIONS FOR USERS OFMOBILE

RADIOS*

Read the literature on the safe operation of the radio.

•Keep both hands on the steering wheel and the microphone in its cradle

whenever the vehicle is in motion.

•Place calls only when vehicle is stopped. Use recall dialing to speed the

time it takes to call.

•When talking from a moving vehicle is unavoidable, drivein the slower

lane. Keep conversations brief.

•If conversation requires taking notes or complex thought, stop the

vehicle in a safe place and continue the call.

Whenever using a mobile radio exercise caution.

*As recommended by the AAA

OPERATING PROCEDURES

Two-wayFM radio systems mustbe operated in accordance with the rules

and regulations of the Federal Communications Commission (FCC).

Operators of two-way radio equipment must be thoroughly familiar with the

rules that apply to the intended type of radio operation. Following these rules

will helpto eliminate confusion, assure the most efficient useof existingradio

channels, and result in a smoothly functioning radio network. When using this

two-way radio remember these rules:

1. It is a violation of FCC rules to interrupt any distress or emergency

message. As the radio operates in much the same way as a telephone

"party line", always listen to make sure that the line is clear - that no

oneelseinon theair-beforesendingmessages.Ifsomeoneissending

an emergency message - such as reporting a fire, or asking for help

in an accident - KEEP OFF THE AIR! Emergency calls have

priority over all other messages.

2. Use of profane or obscene language is prohibited by Federal law.

3. It is against the law to send false call letters, or a false distress or

emergency message.

4. The FCC requires that conversations be kept brief and confined to

business. To save time, use coded messages whenever possible.

5. Using a radio to send personal messages (except in an emergency) is

a violation of the FCC rules. Send only those messages that are

essential for business operation.

6. It is against Federal law to repeat or otherwise make known anything

overheard on the radio. Conversations between others sharing a

channel must be regarded as confidential.

7. The FCC requires the operator to identify himself at certain times by

means of call letters. Refer to therules that apply to the particular type

of operation for the proper procedure.

8. No changes or adjustments shall be madeto the equipment except by

an authorized or certified electronics technician.

INTRODUCTION

This manual describes how to use the MDX Conventional Mobile Radio.

The MDX is a synthesized, microprocessor-based, high performance simplex

mobile FM radio providing reliable two-way communications. Direct mobile

to mobile communication, when out of repeater range, is also provided.

In the Conventional mode, the user selects a channel and directly

communicatesonthatchannel.Inthismode,asystemreferstoasetofchannels

and a channel is a transmit/receive radio frequency pair.

The exact operation of the radio will depend on the operating mode, the

radio’s programming, and the particular radio system. Most features described

in this manual may be enabled or disabled through programming. Consult the

system administrator for the particular features that are programmed into your

MDX radio.

The following feature encrypted options are standard with the MDX

conventional mobile radio:

PMPL3M Serial Control Unit (Control Head Operation)

PMPL3K Scan, Dual Priority

PMPL3F 16 channel operation

PMPL3G 32 channel operation

PMPL3H 64 channel operation

PMPL3J 128 channel operation

The following feature encrypted options can also be ordered:

PMPL3C Type 99 Decode

PMPL3D Public Address and External Speaker Switch (Re-

quires option PMSU5A)

PMPL3E Emergency (GE-STAR) and GE-STAR ANI

CONTROLS, INDICATORS, AND DISPLAYS

The MDX Conventional mobile radio contains ten buttons, an eight

character DOT MATRIX display and seven indicators (see Figure 1). In

addition, there are times when part of the eight character display is used to

display the radio status. Backlighting on buttons illuminate the Legends.

CONTROLS

POWER Momentary push-push switch. Press once to turn

the radio ON. Press again to turn the radio OFF.

VOLUME The momentary switches (auto ramping) VOL-

UME + and VOLUME -. Beeps each time the

VOLUME button is pressed, except when a call is

in process. Hold the button (up or down) to auto

ramp the volume.

Channel/SEL

Ramp scrolls through

the names of channels

programmed into the

radio, displaying them

on the Dot Matrix

display.

Two Flex Keys

give you one-touch

access to the menu or

optional features.

Optional keycaps are

available to identify

the functions of

pre-programmed

buttons, including T99

decode, Scan Add/

Delete, Public

Address, Home,

External Alarm, and

display brightness.

Front-Mounted

Microphone

Connector provides

easy access to the

microphone and

programming

capabilities.

System Key scrolls

through the names of

the system (groups of

channels) program-

med into the radio,

displaying them on

the Dot Matrix display

Front Mount

Speaker with 4 watts

of audio. An optional

10-watt external

speaker is also

available, for use in

noisy environments.

Figure 1 - MDX VHF Conventional Radio

PWR

Volume Up/Down

Ramp sets the volume

of the received audio.

Scan Button

enables scan

operation for the

selected system.

8-Character

Alphanumeric Dot

Matrix LED

allows you to identify

channel selections by

descriptive names.

Names, menu options, and

status information are

displayed here.

MENU button allows access

to functions and options,

including scan add/delete for

modifying the radio’s scan

list and alarm on/off for the

external alarm option that

uses your horn or head lights

to signal an incoming call.

Emergency ID/ Alarm

(optional)

sends an emergency

(GESTAR) alert and

identifying code to the

dispatcher. If no emergency

function is required, this can

be programmed as a

"HOME" switch.

CONTROLS AND INDICATORS

CONTROLS (CONT’D)

MENU Momentary switch. The MENU button is used to

access options on the MDX mobile. Menu opera-

tion is coupled with the CHANNEL/SEL buttons

and theCLR button. To increment from one menu

selection to the next, simply press and release the

MENU button. Press the CLR button to return to

normal operation. The menu choices are listed

below with a description of how to change the

choices (Note: You may have some or all of these

menu choices programmed in your radio, and they

may be programmed in a different order than pre-

sented here).

BACKLIGHT: Press the MENU button until

"BRIGHT" appears in the display. To change the

state of the backlight press the CHANNEL/SEL +

or - button.

PUBLIC ADDRESS: Press the MENU button

until "PUB ADDR" appears in the display. Press

PTT to transmit in PA mode.

SCANADD/DELETE: Press the MENU button

until "SCAN A/D" appears in the display. Use the

CHANNEL/SEL- button to step through the

group selections for the current system. Use the

CHANNEL/SEL + button to change the scan

state. An "S" is illuminated to the right of the

display if the group/channel has SCAN enabled.

ALARMON/OFF: Press the MENUbuttonuntil

"ALM ON" or "ALM OFF"appears in the display.

Press the CHANNEL/SEL+ or -buttons until the

desired state is selected. (Note: This enables or

disables the external alarm e.g. horn or lights.)

SQUELCH Press and hold "Scan" button, use "volume" up to

loosen squelch and down to tighten squelch.

CONTROLS (CONT’D)

SYS Momentary switch. TheSYS (SYSTEM) button is

used to select system changes. System may be

incremented by pressing and releasing the SYS

button. Alternately, when the display shows the

Systemname,theCHANNEL/SELbuttonsmaybe

used to increment or decrement the system selec-

tions.(NOTE: Theradiomaybeprogrammedwith

wrap around on the system selection; this would

allow the radio to switch from thehighestto lowest

system with one change instead of ramping all the

way through the list.)

CHANNEL/SEL Ramp Switch. The CHANNEL/SEL button is

used toincrement or decrementthe current channel

selection. It is also used as described above to

increment/decrement the System. In conventional

mode, these buttons change the channel selection.

CLR Momentaryswitch.TheCLRbuttonisusedtoexit

from the menu operation, monitor a conventional

channel or end a special/individual call.

HOME/

EMERGENCY Momentary switch. The HOME or EMER-

GENCY button is used to select a home system,

orchannel.Theradiomaybeprogrammedtorevert

to a particular system or channel within the se-

lectedor home system.Itmayalsobeprogrammed

to send an emergency message (GESTAR) when

pressed and held for approximately one second

(either on the selected system or on the Home

system).

FLEX KEYS

A1,A2 The auxiliary buttons are used toaccess frequently

used menu selections quickly. They can also be

programmed as a HOME, External Alarm, Public

Address, T99 decode, and Scan add/delete.

DISPLAY INDICATORS

The radio’s display is shown in Figure 2. The character line is used to

display system or area and group or channel names and also operational

messages to the user. The line contains eight Dot Matrix LED characters. The

7 status indicators are used to show the various operating conditions of the

radio.

Inhaltsverzeichnis

Andere Ericsson Radio Handbücher

Ericsson

Ericsson MDX SERIES Bedienungsanleitung

Ericsson

Ericsson LBI-38610A FMD Bedienungsanleitung

Ericsson

Ericsson ORION Bedienungsanleitung

Ericsson

Ericsson MDX SERIES Bedienungsanleitung

Ericsson

Ericsson MDX SERIES Bedienungsanleitung

Ericsson

Ericsson LBI-38953 Bedienungsanleitung

Ericsson

Ericsson MDX LBI-38848C Bedienungsanleitung

Ericsson

Ericsson RBS 2207 Merkblatt

Ericsson

Ericsson MDX LBI-39015C Bedienungsanleitung

Ericsson

Ericsson EDACS Monogram Series Bedienungsanleitung

Ericsson

Ericsson mRRUS 12 Bedienungsanleitung

Ericsson

Ericsson KME-200 Bedienungsanleitung

Ericsson

Ericsson EDACS Monogram Series Bedienungsanleitung

Ericsson

Ericsson EDACS PRISM HP Bedienungsanleitung

Ericsson

Ericsson MDX LBI-39015D Bedienungsanleitung

Ericsson

Ericsson EDACS IPE SERIES Bedienungsanleitung

Ericsson

Ericsson LBI-39014B Bedienungsanleitung

Ericsson

Ericsson MDX LBI-39015 Bedienungsanleitung

Ericsson

Ericsson Orion 38901E Bedienungsanleitung

Ericsson

Ericsson LBI-38848E Bedienungsanleitung

Ericsson

Ericsson 2203 Bedienungs- und Montageanleitung

Ericsson

Ericsson MOBITEX BRU3 Bedienungsanleitung

Ericsson

Ericsson MDX GE-MARC Service-Handbuch

Ericsson

Ericsson ORION Bedienungsanleitung

Beliebte Radio Handbücher anderer Marken

EisSound

EisSound KBSound iSelect Bedienungsanleitung

Midland

Midland 1001LWX Bedienungsanleitung

Konig

Konig HAV-SR41 Bedienungsanleitung

Roberts

Roberts exprssion Bedienungsanleitung

VDigi

VDigi DD3.0 Bedienungsanleitung

Radio Shack

Radio Shack 21-1863 Bedienungsanleitung

Roberts

Roberts Stream 207 Bedienungsanleitung

Sony

Sony Walkman SRF-M97 Bedienungsanleitung

Stanley

Stanley FatMax FMC770 Bedienungsanleitung

auna

auna DAB-Radio 10026947 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR190 Bedienungsanleitung

HYT

HYT TC-320 Bedienungsanleitung

auna multimedia

auna multimedia Yellowstone 10026851 Bedienungsanleitung

B-Tech

B-Tech GMRS-V2 Bedienungsanleitung

Weierwei

Weierwei VEV-V8 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER DAB750 Bedienungsanleitung

Telefunken

Telefunken TF-1505 Bedienungsanleitung

Makita

Makita LXRM03 Bedienungsanleitung