ESAB Cro Bedienungsanleitung

Crossbow Installation

Article Number: 0560956420

Revision Date: April 30, 2015

Revision Number: 00

Language: ENG

Quick Start Guide

Refer to Crossbow Instruction Manual

for detailed installation instructions.

CROSSBOW QUICK-START GUIDE

1Check Package Contents

Carefully check the content of the package, and identify which components will be used.

Central Unit

Rail Track

Cross Beam

Plasma Torch Holders

(One clamp is pre-installed on

Cross Beam)

Torch Lifter

Plasma Touch Cable (2-pin) Plasma Interface Cable (6-pin to 14-pin)

Torch Holder

Required for use with Plasma torch

Required for all Crossbow installations

INSTALLATION

Stabilizer Feet

3 included with 5x10 machine

2 included with 4x4 machine

M8 Screws

12 included with 5x10 machine

8 included with 4x4 machine

Bumper Stops (2)

M6 x 40 Screws (2)

Power Cable Lift/Solenoid Cable (4-pin)

Second Torch Holder

Oxy-Fuel Torch

Adaptor

Torch Lifter

Spacer

Required for use with Oxy-Fuel torch

Required when installing BOTH Oxy-Fuel

AND Plasma torches on same machine.

M6 Torch Lifter

Mounting Screw

M6 Torch Holder

Mounting Screw

CROSSBOW QUICK-START GUIDE

2Basic Machine Assembly

Attach Stabilizer Feet to bottom of Rail Track using M8 screws.

Slide Central Unit onto Rail Track.

STEP 1

STEP 2

INSTALLATION

Install Bumper Stops to Rail Track using M6x40 Screws.

Slide Cross Beam through the Central Unit.

STEP 3

STEP 4

Remove existing screw from last

hole at each end of the rail. Take

care not to loose track of the nut

in the slot of the extrusion. Do

not over-tighten screw, it will

bottom out in the extrusion.

CROSSBOW QUICK-START GUIDE

2Basic Machine Assembly (Continued)

STEP 5

STEP 6

Mount Torch Holder and Mount Motorized Torch Lifter to end of Cross Beam.

Connect Lift/Solenoid Cable and Power Cable

Connect Lift/Solenoid Cable

between the 4-Pin connector

on back of the Crossbow, and

the 4-Pin connector ad the

end of the Cross-Beam.

INSTALLATION

STEP 1

STEP 2

3Optional Oxy-Fuel Torch Assembly

Assemble and install Oxy-Fuel Torch

Connect Oxy-Fuel Supply Hoses.

Connect gas supply hoses to

regulated supply of oxygen and

fuel gas.

Insert oxy-fuel torch into torch

holder using Oxy-Fuel Torch

Adaptor. Connect center oxygen

hose (Cutting Oxygen) to the

output of the solenoid valve.

Skip this section if not installing oxy-fuel torch with the Crossbow.

CROSSBOW QUICK-START GUIDE

4Optional Plasma System Assembly

STEP 1

STEP 2

Install Cable Holders

Install Plasma Torch with Torch Lead

Connect plasma torch lead to the

plasma power source as directed

in the plasma power source

instruction manual.

Skip this section if not installing plasma with the Crossbow.

INSTALLATION

STEP 3 Install Plasma Touch Cable

Connect black wire to

table or work ground.

Connect red wire to

torch shield.

Connect Plasma Touch

Cable to the 2-Pin connector

on back of Crossbow.

CROSSBOW QUICK-START GUIDE

STEP 4 Install Plasma Interface Cable

Connect Plasma Interface

Cable to the 14-pin

connector on the back of

the plasma power source.

Connect Plasma Interface

Cable to the 6-Pin connector

on back of Crossbow.

Inhaltsverzeichnis

Andere ESAB Industrieanlagen Handbücher

ESAB

ESAB OPC Flux recovery unit Bedienungsanleitung

ESAB

ESAB Warrior Feed 304 Bedienungsanleitung

ESAB

ESAB A6 Mastertrac A6TF Bedienungsanleitung

ESAB

ESAB Tweco OCIM RB25T Bedienungsanleitung

ESAB

ESAB ESD 7.5 Bedienungsanleitung

ESAB

ESAB MechTrac 2500 Bedienungsanleitung

ESAB

ESAB MechTrac 1730 Bedienungsanleitung

ESAB

ESAB KHM 2x400 PS Bedienungsanleitung

ESAB

ESAB A6 TPC 75 Bedienungsanleitung

ESAB

ESAB A6 CRE 30 Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

ESAB

ESAB GASARC GPE 400 Series Handbuch

ESAB

ESAB ECD 7.5 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung