ESAB Caddy Tig 1500i Bedienungsanleitung

Valid for serial no. 803--xxx--xxxx0460 443 001 GB 080129

Tig 1500i/2200i

Caddy t

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 5...................................................

3.1 Equipment 5................................................................

3.2 Control panels 5............................................................

4 TECHNICAL DATA 5.................................................

5 INSTALLATION 6....................................................

5.1 Location 6..................................................................

5.2 Mains power supply 7........................................................

6 OPERATION 8.......................................................

6.1 Connections and control devices 8............................................

6.2 Key to symbols 8............................................................

6.3 Water connection 8..........................................................

6.4 TIG--welding 9..............................................................

6.5 MMA--svetsning 9...........................................................

6.6 Overheating protection 9.....................................................

6.7 Connection to cooling unit

(only valid for Caddyt Tig 2200i) 9.............................................

6.8 Turning on the power source 9................................................

7 MAINTENANCE 10....................................................

7.1 Inspection and cleaning 10....................................................

8 FAULT--TRACING 10..................................................

9 ORDERING SPARE PARTS 11..........................................

10 DISMANTLING AND SCRAPPING 11...................................

DIAGRAM 12............................................................

ORDERING NUMBER 18.................................................

ACCESSORIES 19.......................................................

NOTES 22......................................................

-- 3 --

bt34d1ea

1DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-

ing power source Tig 1500i, 2200i, 2200iw from serial number 803 are constructed and tested in

compliance with the standard EN 60974--1 /--3 and EN 60974--10 (Class A) in accordance with the

requirements of directive (2006/95/EC) and (2004/108/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Kent Eimbrodt

Global Director

Equipment and Automation

Laxå 2008--01--25

2SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding

2. The operator must ensure that:

Sno unauthorized person is stationed within the working area of the equipment when it is

started up.

Sno--one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

SDo not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

-- 4 --

bt34d1ea

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precausions when welding.

Ask for your employer’s safety practices which should be based on manufacturers’ hazard data.

ELECTRIC SHOCK - Can kill

SInstall and earth the welding unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection and accessories.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Read and understand the instruction manual before

installing or operating.

CAUTION!

This product is solely intended for arc welding.

CAUTION!

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low--voltage supply

system. There may be potential difficulties in ensuring electromagnic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

-- 5 --

bt34d1ea

3 INTRODUCTION

The Tig 1500i / 2200i is a TIG welding power source, which can also be used for

MMA welding. It can be used direct current (DC).

ESAB’s accessories for the product can be found on page 19.

3.1 Equipment

Thepowersourceissuppliedwitha3mweldingcablecompletewithaTIG--torch,

3 m return cable, 3 m mains cable, instruction manual for power source and control

panel, see Ordering information on page 18.

3.2 Control panels

STA33 STA34

See the separate instruction manual for a detailed description of the control panels.

4 TECHNICAL DATA

Tig 1500i Tig 2200i/2200iw

Mains voltage 230V, ±10%, 1∼50/60 Hz 230V, ±10%, 1∼50/60 Hz

Primary current

Imax TIG

Imax MMA

13.8 A

21.3 A

24.1 A

24.9 A

Mains supply Zmax 0.35 ohm Zmax 0.30 ohm

No--load power 30 W 30 W

Setting range

TIG

MMA

3 -- 150 A

4 -- 150 A

3 -- 220 A

4 -- 170 A

Permissible load at TIG

20% duty cycle

25% duty cycle

60% duty cycle

100% duty cycle

150 A / 16.0 V

120 A / 14.8 V

110A/14.4V

220 A / 18.8 V

150 A / 16.0 V

110A/14.4V

Permissible load at MMA

30% duty cycle

60% duty cycle

100% duty cycle

150 A / 26.0 V

100 A / 24.0 V

90 A / 23.6 V

170 A / 26.8 V

130 A / 25.2 V

110A/24.4V

Power factor at maximum current

TIG

MMA

0.99

-- 6 --

bt34d1ea

Tig 2200i/2200iwTig 1500i

Efficiency at maximum current

TIG

MMA

76 %

80 %

78 %

81 %

Open--circuit voltage MMA 72 V 72 V

Operating temperature -- 1 0 t o + 4 0 ˚C-- 1 0 t o + 4 0 ˚C

Transportation temperature -- 2 0 t o + 5 5 ˚C-- 2 0 t o + 5 5 ˚C

Constant sound pressure in

open--circuit <70dB(A) <70dB(A)

Dimensions, l x b x h 418 x 188 x 208 mm 418 x 188 x 208 mm

including the cooling unit -- 418 x 188 x 345 mm

Weight

cooling unit with/without cooling water

9.2 kg

9.4 kg

6.7 / 4.5 kg

Shielding gas

max pressure

All types intended for TIG

welding

5 bar

All types intended for TIG

welding

5 bar

Insulation class transformer H H

Enclosure class IP 23 IP 23

Application class

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

The duty cycle is valid for 40˚C ambient temperature.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

Mains supply, Zmax

Maximum permissible line on the network impedance in accordance with IEC 61000--3--11.

5 INSTALLATION

The installation must be executed by a professional.

Note!

Mains supply requirements

High power equipment may, due to the primary current drawn from the mains supply, influence the

power quality of the grid. Therefore connection restrictions or requirements regarding the

maximum permissible mains impedance or the required minimum supply capacity at the interface

point to the public grid may apply for some types of equipment (see technical data). In this case it

is the responsibility of the installer or user of the equipment to ensure, by consultation with the

distrubution network operator if necessary, that the equipment may be connected.

5.1 Location

Position the welding power source such that its cooling air inlets and outlets are not

obstructed.

-- 7 --

bt34d1ea

5.2 Mains power supply

Check that the welding power source is connected to the

correct mains power supply voltage, and that it is

protected by the correct fuse size.

A protective earth connection must be made in

accordance with regulations.

Rating plate with supply connection data

Recommended fuse sizes and minimum cable area

Tig 1500i Tig 2200i/2200iw

TIG MMA TIG MMA

Mains voltage 230 V ¦10 %,

1μ

230 V ¦10 %,

1μ

230 V ¦10 %,

1μ

230 V ¦10 %,

1μ

Mains frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz

Mains cable area mm23G2.5 3G2.5 3G2.5 3G2.5

Phase current I1eff 9.1 A 11.5 A 11.5 A 13.4 A

Fuse

anti--surge

type C MCB

16 A

13 A

16 A

13 A

16 A

NOTE! The mains cable areas and fuse sizes as shown above are in accordance with Swedish

regulations. Use the welding power source in accordance with the relevant national regulations.

-- 8 --

bt34d1ea

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

6.1 Connections and control devices

1Connection (+) for the return cable for

TIG.

MMA: for the return cable or the welding

cable.

7Mains switch

2Connection for the remote control unit 8Mains cable

3Control panel (see separate instruction

manual)

9Connection for shiedling gas

4Connection for the TIG--torch 10 Connection BLUE, with ELP* for cooling

water from the cooling unit

5Connection for gas to the TIG--torch 11 Connection RED for cooling water to the

cooling unit.

6Connection (--) for the TIG--torch

MMA: return cable or welding cable

12 Refilling of cooling water

* ESAB Logic Pump, see under 6.3

6.2 Key to symbols

MMA TIG

6.3 Water connection

The cooling unit is equipped with a detection system ELP (ESAB Logic Pump) which

checks that the water hoses are connected. When connecting a water--cooled TIG

torchcoolingstarts.

-- 9 --

bt34d1ea

6.4 TIG--welding

Before using the Arc 1500i/2200i for TIG welding it must be equipped with:

Sa TIG torch

Sa cylinder of suitable welding gas

Sa welding gas regulator (suitable gas regulator)

Stungsten electrodes

Ssuitable filler metal, if necessary

6.5 MMA--svetsning

Connection of welding and return cable

The welding power source has two terminals, one plus and one minus pole, for the con-

nection of the welding and the return cable. Connect the welding cable to the pole indi-

cated on the package of the electrode to be used.

Connect the return cable to the other terminal. Fit the earth clamp of the return cable

to the work--piece and make sure there is good contact between the work--piece and

the return cable terminal on the welding power source.

6.6 Overheating protection

The power source has two thermal overload trips which operate if the internal

temperature becomes too high. A fault code is shown in the panel. They reset

automatically when the temperature has fallen.

6.7 Connection to cooling unit

(only valid for CaddytTig 2200i)

Only those persons who have appropriate electrical

knowledge (authorized personnel) may remove the

safety plates to connect or carry out service,

maintenance or repair work on welding equipment.

See installation instructions in the instruction manual

for the cooling unit.

6.8 Turning on the power source

Turn on the mains power by turning the mains switch to the ”1” position.

Turn the unit off by turning the switch to the ”0” position.

Whether the mains power supply is interrupted or the power unit is switched off in

the normal manner, welding data will be stored and is available next time the unit is

started.

-- 1 0 --

bt34d1ea

7 MAINTENANCE

Regular maintenance is important for safe, reliable operation.

Only those persons who have appropriate electrical knowledge (authorized

personnel) may remove the safety plates to connect or carry out service,

maintenance or repair work on welding equipment.

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself

attempts any work in the product during the guarantee period in order to rectify any

faults.

7.1 Inspection and cleaning

Power source

Check regularly that the welding power source is not clogged with dirt.

How often and which cleaning methods apply depend on: the welding process, arc

times, placement, and the surrounding environment. It is normally sufficient to blow

down the power source with dry compressed air (reduced pressure) once a year.

Clogged or blocked air inlets and outlets otherwise result in overheating.

Welding torch

The welding torch’s wear parts should be cleaned and replaced at regular intervals in

order to achieve trouble--free welding.

8 FAULT--TRACING

Try these recommended checks and inspections before sending for an authorised

service technician.

Type of fault Corrective action

No arc. SCheck that the mains power supply switch is turned on.

SCheck that the welding current supply and return cables are

correctly connected.

SCheck that the correct current value is set.

SCheck the mains power supply.

The welding current is

interrupted during welding.

SCheck to see whether the thermal cut--outs have tripped.

SCheck the mains power supply fuses.

The thermal cut--out trips

frequently.

SMake sure that you are not exceeding the rated data for the

welding power source (i.e. that the unit is not being

overloaded).

SMake sure that the power source is clean.

Poor welding performance. SCheck that the welding current supply and return cables are

correctly connected.

SCheck that the correct current value is set.

SCheck that the correct electrodes are being used.

SCheck the gas flow.

Andere Handbücher für Caddy Tig 1500i

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Thermal Dynamics CUTMASTER 40 Bedienungsanleitung

ESAB

ESAB EPP-200 Bedienungsanleitung

ESAB

ESAB Mig 4004 iMV Leitfaden

ESAB

ESAB LHI 825 Leitfaden

ESAB

ESAB Mig 4004i Bedienungsanleitung

ESAB

ESAB Powercut 875 Bedienungsanleitung

ESAB

ESAB Aristo Mig U5000i 400 V Bedienungsanleitung

ESAB

ESAB LKA 180 Bedienungsanleitung

ESAB

ESAB Caddy Mig C200i Bedienungsanleitung

ESAB

ESAB Caddy Arc 251i Bedienungsanleitung

ESAB

ESAB Aristotig 255 LTN 255 Bedienungsanleitung

ESAB

ESAB Aristo Mig 5000i 400 V Bedienungsanleitung

ESAB

ESAB Warrior 400i MV CC/CV Bedienungsanleitung

ESAB

ESAB Aristo Mig U4000i Bedienungsanleitung

ESAB

ESAB Caddy Tig 1500i VRD Bedienungsanleitung

ESAB

ESAB MIG400iCCCV Bedienungsanleitung

ESAB

ESAB Origo Tig 3001i Bedienungsanleitung

ESAB

ESAB Warrior 400i CC/CV Bedienungsanleitung

ESAB

ESAB Mig 4004i Bedienungsanleitung

ESAB

ESAB Migmaster 275 Bedienungsanleitung

ESAB

ESAB Origo Mig 4002c Bedienungsanleitung

ESAB

ESAB SR-B 9 Bedienungsanleitung

ESAB

ESAB CIGWELD WeldSkill MicroArc 140 Bedienungsanleitung

ESAB

ESAB Aristo WeldCloud Mig U5000i Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung