ESAB Origo Mig 4002c Bedienungsanleitung

Origo™

Instruction manual

0463 264 001 GB 20170310 Valid for: serial no. 136-, 740-, 745-, 801-, 806-xxx-xxxx

Mig4002c

Mig5002c

Mig 6502c

TABLE OF CONTENTS

0463 264 001 © ESAB AB 2017

1SAFETY ......................................................................................................... 4

1.1 Meaning of symbols ................................................................................. 4

1.2 Safety precautions ................................................................................... 4

2INTRODUCTION............................................................................................ 7

2.1 Equipment ................................................................................................. 7

3TECHNICAL DATA ........................................................................................ 8

4INSTALLATION.............................................................................................. 12

4.1 Location..................................................................................................... 12

4.2 Assembly of components........................................................................ 13

4.3 Mains power supply ................................................................................. 14

5OPERATION .................................................................................................. 16

5.1 Connections and control devices ........................................................... 17

5.2 Overheating protection ............................................................................ 17

5.3 Water connection ..................................................................................... 17

5.4 Water flow guard ...................................................................................... 18

5.5 MIG/MAG and FCAW-S welding .............................................................. 18

5.6 MMA welding............................................................................................. 18

5.7 TIG welding ............................................................................................... 18

6MAINTENANCE............................................................................................. 19

6.1 Inspection and cleaning........................................................................... 19

6.1.1 Power source ......................................................................................... 19

6.1.2 Welding torch.......................................................................................... 19

6.2 Topping up the coolant ............................................................................ 19

7FAULT TRACING........................................................................................... 20

8ORDERING SPARE PARTS .......................................................................... 21

CLEANING............................................................................................................ 22

DIAGRAM ............................................................................................................. 23

CONNECTION INSTRUCTION............................................................................. 26

ORDER NUMBERS .............................................................................................. 28

ACCESSORIES .................................................................................................... 29

Rights reserved to alter specifications without notice.

1 SAFETY

0463 264 001 -4- © ESAB AB 2017

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and Safety

Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0463 264 001 -5- © ESAB AB 2017

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or

work cable around your body. Keep welding power source and

cables as far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0463 264 001 -6- © ESAB AB 2017

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be potential

difficulties in ensuring electromagnetic compatibility of class

A equipment in those locations, due to conducted as well

as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation

in accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be

disposed of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0463 264 001 -7- © ESAB AB 2017

2 INTRODUCTION

The Mig 4002c, Mig 5002c and Mig 6502c are welding power sources intended for

MIG/MAG welding, as well as for welding with powder filled cored wire (FCAW-S), Live TIG

welding (only with some of the control panels) and for welding with coated and cellulosic

electrodes (MMA).

The power sources are intended for use with the following wire feed units:

• Feed 3004/4804

• MobileFeed 300

• YardFeed 2000

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

2.1 Equipment

The power source is supplied with:

• Return cable 5m with return clamp

• Shelf for gas cylinder

• Attachment chain for gas cylinder

• Guide pin for wire feed unit

• Cooling unit (if applicable)

• Instruction manual

3 TECHNICAL DATA

0463 264 001 -8- © ESAB AB 2017

3 TECHNICAL DATA

Mig 4002c

Mains voltage 380/400 - 415 V, +/-10%, 3~ 50/60 Hz

230/400 - 415/440 - 460/500 V, +/-10%, 3~ 50/60 Hz

Permissible load at MIG/MAG

60% duty cycle 400 A / 34.0 V

100% duty cycle 310 A / 30.0 V

Permissible load at MMA

60% duty cycle 400 A / 36.0 V

100% duty cycle 310 A / 33.0 V

Welding range 1)

MIG/MAG 20 A / 15 V - 400 A / 34.0 V

MMA 20 A / 20.8 V - 400 A / 36.0 V

Open circuit voltage

MIG/MAG without VRD function 3) 68.0 V

MMA without VRD function 3) 62.0 V

VRD function deactivated 4) 56.0 V

VRD function activated 4) < 35.0 V

Open circuit power 500 W

with cooling unit 700 W

in energy saving mode (15 min

after last welding) 2)

60 W

Power factor at maximum current

MMA

0.88

Efficiency at maximum current

MMA

70%

Control voltage 42.0 V, 50/60 Hz

Dimensions l × w × h 830 × 640 × 835 mm (32.7 × 25.2 × 32.9 in.)

Weight 149 kg (328.5 lb)

with cooling unit 163 kg (359.4 lb)

Operating temperature -10 to +40° C (+14 to +104 °F)

Transportation temperature -20 to +55° C (-4 to +131 °F)

Enclosure class IP 23

Application classification

1) Welding ranges are different to the possible setting range on the panel.

2) Power saving mode works only in MIG/MAG.

3) Valid for power sources without VRD specification on the rating plate.

4) Valid for power sources with VRD specification on the rating plate. The VRD function is

explained in the instruction manual for the control panel.

3 TECHNICAL DATA

0463 264 001 -9- © ESAB AB 2017

Mig 5002c

Mains voltage 380/400 - 415 V, +/-10%, 3~ 50/60 Hz

230/400 - 415/440 - 460/500 V, +/-10%, 3~ 50/60 Hz

Permissible load at MIG/MAG

60% duty cycle 500 A / 39.0 V

100% duty cycle 400 A / 34.0 V

Permissible load at MMA

60% duty cycle 500 A / 40.0 V

100% duty cycle 400 A / 36.0 V

Welding range 1)

MIG/MAG 20 A / 15.0 V - 500 A / 39.0 V

MMA 20 A / 20.8 V - 500 A / 40.0 V

Open circuit voltage

MIG/MAG without VRD function 3) 68.0 V

MMA without VRD function 3) 62.0 V

VRD function deactivated 4) 56.0 V

VRD function activated 4) < 35.0 V

Open circuit power 550 W

with cooling unit 750 W

in energy saving mode (15 min

after last welding) 2)

60 W

Power factor at maximum current

MMA

0.90

Efficiency at maximum current

MMA

72%

Control voltage 42.0 V, 50/60 Hz

Dimensions l × w × h 830 × 640 × 835 mm (32.7 × 25.2 × 32.9 in.)

Weight 185 kg (407.9 lb)

with cooling unit 199 kg (438.7 lb)

Operating temperature -10 to +40° C (+14 to +104 °F)

Transportation temperature -20 to +55° C (-4 to +131 °F)

Enclosure class IP 23

Application classification

1) Welding ranges are different to the possible setting range on the panel.

2) Power saving mode works only in MIG/MAG.

3) Valid for power sources without VRD specification on the rating plate.

4) Valid for power sources with VRD specification on the rating plate. The VRD function is

explained in the instruction manual for the control panel.

3 TECHNICAL DATA

0463 264 001 - 10 - © ESAB AB 2017

Mig 6502c

Mains voltage 380/400 - 415 V, +/-10%, 3~ 50/60 Hz

230/400 - 415/440 - 460/500 V, +/-10%, 3~ 50/60 Hz

Permissible load at MIG/MAG

60% duty cycle 650 A / 44.0 V

100% duty cycle 500 A / 39.0 V

Permissible load at MMA

60% duty cycle 650 A / 44.0 V

100% duty cycle 500 A / 40.0 V

Welding range 1)

MIG/MAG 20 A / 15.0 V - 650 A / 39.0 V

MMA 20 A / 20.8 V - 650 A / 40.0 V

Open circuit voltage

MIG/MAG without VRD function 3) 68.0 V

MMA without VRD function 3) 62.0 V

VRD function deactivated 4) 56.0 V

VRD function activated 4) < 35.0 V

Open circuit power 670 W

with cooling unit 870 W

in energy saving mode (15 min

after last welding) 2)

60 W

Power factor at maximum current

MMA

0.90

Efficiency at maximum current

MMA

76%

Control voltage 42.0 V, 50/60 Hz

Dimensions l × w × h 830 × 640 × 835 mm (32.7 × 25.2 × 32.9 in.)

Weight 222 kg (489.4 lb)

with cooling unit 236 kg (520.3 lb)

Operating temperature -10 to +40° C (+14 to +104 °F)

Transportation temperature -20 to +55° C (-4 to +131 °F)

Enclosure class IP 23

Application classification

1) Welding ranges are different to the possible setting range on the panel.

2) Power saving mode works only in MIG/MAG.

3) Valid for power sources without VRD specification on the rating plate.

4) Valid for power sources with VRD specification on the rating plate. The VRD function is

explained in the instruction manual for the control panel.

Andere Handbücher für Origo Mig 4002c

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB ES 95i Bedienungsanleitung

ESAB

ESAB EMP235ic Bedienungsanleitung

ESAB

ESAB Caddy Mig C200i Bedienungsanleitung

ESAB

ESAB Origo Mig 410 Bedienungsanleitung

ESAB

ESAB CoolMidi 1800 Bedienungsanleitung

ESAB

ESAB Origo Mig 4002c Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

ESAB

ESAB Miggytrac 1001 Bedienungsanleitung

ESAB

ESAB LKB 265 Bedienungsanleitung

ESAB

ESAB PKB 250 Bedienungsanleitung

ESAB

ESAB WARRIOR EDGE 500 Bedienungsanleitung

ESAB

ESAB RS 400x Bedienungsanleitung

ESAB

ESAB Origo Mig L305 Bedienungsanleitung

ESAB

ESAB Origo Mig 652c Bedienungsanleitung

ESAB

ESAB Warrior 750i CC/CV Bedienungsanleitung

ESAB

ESAB fabricator 141i Bedienungsanleitung

ESAB

ESAB fabricator 211i Bedienungsanleitung

ESAB

ESAB PT-19A Bedienungsanleitung

ESAB

ESAB Rogue ES 180i Bedienungsanleitung

ESAB

ESAB EMP 210 Bedienungsanleitung

ESAB

ESAB Cutmaster 40 SL60 1Torch Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Tandem Bedienungsanleitung

ESAB

ESAB ET 186i AC/DC Bedienungsanleitung

ESAB

ESAB Origo Arc 406 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung