ESAB Origo Tig 4300iw AC/DC Bedienungsanleitung

Origo™

Instruction manual

0460 157 301 GB 20181217 Valid for: 950-xxx-xxxx

Tig 4300iw AC/DC

TABLE OF CONTENTS

0460 157 301 © ESAB AB 2018

1SAFETY ....................................................................................................... 4

1.1 Meaning of symbols ............................................................................... 4

1.2 Safety precautions ................................................................................. 4

2INTRODUCTION.......................................................................................... 7

2.1 Equipment ............................................................................................... 7

2.2 The control panel.................................................................................... 7

3TECHNICAL DATA ...................................................................................... 8

4INSTALLATION............................................................................................ 10

4.1 Lifting instructions ................................................................................. 10

4.2 Positioning of the power source........................................................... 10

4.3 Mains power supply ............................................................................... 11

5OPERATION ................................................................................................ 12

5.1 Connections and control devices ......................................................... 12

5.2 Key to symbols....................................................................................... 13

5.3 Turning on the power source ................................................................ 13

5.4 Fan control .............................................................................................. 13

5.5 Overheating protection .......................................................................... 13

5.6 Cooling unit............................................................................................. 13

6MAINTENANCE........................................................................................... 15

6.1 Cleaning the filter ................................................................................... 15

6.2 Topping up the coolant .......................................................................... 15

7TROUBLESHOOTING ................................................................................. 16

8ORDERING SPARE PARTS ........................................................................ 17

DIAGRAM ............................................................................................................ 18

ORDERING NUMBERS....................................................................................... 22

SPARE PARTS LIST............................................................................................ 23

ACCESSORIES ................................................................................................... 24

Rights reserved to alter specifications without notice.

1 SAFETY

0460 157 301 -4- © ESAB AB 2018

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in

immediate, serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss

of life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and

Safety Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0460 157 301 -5- © ESAB AB 2018

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or work

cable around your body. Keep welding power source and cables as

far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

1 SAFETY

0460 157 301 -6- © ESAB AB 2018

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable

materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be

potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations,

due to conducted as well as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on

Waste Electrical and Electronic Equipment and its

implementation in accordance with national law,

electrical and/or electronic equipment that has reached

the end of its life must be disposed of at a recycling

facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved

collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0460 157 301 -7- © ESAB AB 2018

2 INTRODUCTION

The Tig 4300iw AC/DC is a TIG welding power source, which can also be used for MMA

welding. The power welding source can be used with alternating current (AC) or direct

current (DC).

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

2.1 Equipment

The power source is delivered with 5m (16.4ft) mains cable including the plug, 5m (16.4ft)

return cable, instruction manuals for power source and for the control panel.

Instruction manuals in other languages can be downloaded from the Internet: www.esab.com

2.2 The control panel

TA24 AC/DC

See the separate instructions for detailed descriptions of the control panel.

3 TECHNICAL DATA

0460 157 301 -8- © ESAB AB 2018

3 TECHNICAL DATA

Tig 4300iw AC/DC

Mains voltage 400V ±10%, 3~ 50Hz

Mains supply

Ssc min 2.6MVA

Zmax 0.24Ohm

Primary current

Imax TIG 25A

Imax MMA 32A

No-load power in energy-saving mode 6.5 min.

after welding

75W

Voltage/current range

TIG AC*/DC 4–430A

MMA 16–430A

Permissible load at TIG

40 % duty cycle 430A / 27.2V

60 % duty cycle 400A / 26.0V

100 % duty cycle 315A / 22.6V

Permissible load at MMA

40 % duty cycle 430A / 37.2V

60 % duty cycle 400A / 36.0V

100 % duty cycle 315A / 32.6V

Power factor at maximum current

TIG 0.89

MMA 0.89

Efficiency at maximum current

TIG 76%

MMA 80%

Open-circuit voltage U0max

without VRD function 1) 83V

U0L "Live TIG" , VRD function deactivated 2) 60V

MMA, VRD function deactivated 2) 60V

VRD function activated 2) <35V

Operating temperature range -10 to +40°C (+14 to +104°F)

Transportation temperature -20 to +55°C (-4 to +131°F)

Dimensions l × w × h 625×394×776mm

(24.6×15.5×30.5in.)

Continual sound pressure at no-load <70db(A)

Weight 95kg (209.4lb)

Insulation class H

3 TECHNICAL DATA

0460 157 301 -9- © ESAB AB 2018

Tig 4300iw AC/DC

Enclosure class IP23

Application class

*) The minimum current during AC welding depends on the alloy used for the aluminium

plates and their surface cleanliness.

1) Valid for power sources without VRD specification on the rating plate.

2) Valid for power sources with VRD specification on the rating plate. The VRD function is

explained in the instruction manual for the control panel if the panel has that function.

Cooling unit

Cooling power 2.0kW at 40°C (104°F) temperature

difference and flow 1.0l/min (0.26gpm)

Coolant ESAB ready mixed coolant

Liquid quantity 5.5l (1.45gal)

Maximum water flow 2.0l/min (0.53gpm)

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or

cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

Mains supply, Ssc min

Minimum short circuit power on the network in accordance with IEC 61000-3-12.

Mains supply, Zmax

Maximum permissible line impedance of the network in accordance with IEC 61000-3-11.

4 INSTALLATION

0460 157 301 - 10 - © ESAB AB 2018

4 INSTALLATION

The installation must be carried out by a professional.

NOTE!

Mains supply requirements

This equipment complies with IEC 61000-3-12 provided that the short-circuit power is

greater than or equal to Sscmin at the interface point between the user's supply and

the public system. It is the responsibility of the installer or user of the equipment to

ensure, by consultation with the distribution network operator if necessary, that the

equipment is connected only to a supply with a short-circuit power greater than or

equal to Sscmin. Refer to the technical data in the TECHNICAL DATA chapter.

4.1 Lifting instructions

With power source With trolley and power source

4.2 Positioning of the power source

Position the welding power source in such a way that its cooling air inlets and outlets are not

obstructed.

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Aristo Origo Feed 4804 Bedienungsanleitung

ESAB

ESAB PowerCut 700 PT-39 Bedienungsanleitung

ESAB

ESAB THERMAL DINAMICS CUTMASTER 60i Bedienungsanleitung

ESAB

ESAB ESABMig C280 Bedienungsanleitung

ESAB

ESAB TAF 801 Bedienungsanleitung

ESAB

ESAB EMP 205ic AC/DC Bedienungsanleitung

ESAB

ESAB Miggytrac 2000 Bedienungsanleitung

ESAB

ESAB CaddyArc 150 Bedienungsanleitung

ESAB

ESAB AristoMig U500 Bedienungsanleitung

ESAB

ESAB Tig 4000i Aristo Bedienungsanleitung

ESAB

ESAB Cutmaster 40 Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Tandem Bedienungsanleitung

ESAB

ESAB SCT-1500 SERIES Bedienungsanleitung

ESAB

ESAB ESP-150 Bedienungsanleitung

ESAB

ESAB MobileFeed 201 AVS Bedienungsanleitung

ESAB

ESAB Renegade ET 300i Bedienungsanleitung

ESAB

ESAB Origo Tig 3001i Bedienungsanleitung

ESAB

ESAB ESP-101 Bedienungsanleitung

ESAB

ESAB Aristotig 405 AC/DC Bedienungsanleitung

ESAB

ESAB Origo Arc 256 Leitfaden

ESAB

ESAB LHI 825 Leitfaden

ESAB

ESAB Origo Arc 250 edw Leitfaden

ESAB

ESAB Origo Feed 484 P5 Bedienungsanleitung

ESAB

ESAB Caddy 150 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung

Everlast

Everlast POWER MTS 221STi Bedienungsanleitung