ESAB Warrior YardFeed 200 Bedienungsanleitung

Instruction manual

0463 387 201 GB 20180115 Valid for: serial no. 802-xxx-xxxx

Warrior™ YardFeed 200

Warrior™YardFeed200w

TABLE OF CONTENTS

0463 387 201 © ESAB AB 2018

1SAFETY ....................................................................................................... 4

1.1 Meaning of symbols ............................................................................... 4

1.2 Safety precautions ................................................................................. 4

2INTRODUCTION.......................................................................................... 8

3TECHNICAL DATA ...................................................................................... 9

4INSTALLATION............................................................................................ 10

4.1 Lifting instructions ................................................................................. 10

5OPERATION ................................................................................................ 11

5.1 Connections and control devices ......................................................... 12

5.2 Function .................................................................................................. 13

5.3 Wire feed pressure ................................................................................. 14

5.4 Replacing and inserting wire................................................................. 15

5.5 Changing feed rollers............................................................................. 15

6MAINTENANCE........................................................................................... 16

6.1 Inspection and cleaning......................................................................... 16

7ORDERING SPARE PARTS ........................................................................ 17

DIAGRAM ............................................................................................................ 18

ORDERING NUMBERS....................................................................................... 20

WEAR PARTS...................................................................................................... 21

ACCESSORIES ................................................................................................... 26

Rights reserved to alter specifications without notice.

1 SAFETY

0463 387 201 -4- © ESAB AB 2018

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer´s safety practices and Safety

Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet the requirements that apply to this type of equipment. The following

recommendations should be observed in addition to the standard regulations that apply to

the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can

result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops

○ its function

○ relevant safety precautions

○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:

○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts

1 SAFETY

0463 387 201 -5- © ESAB AB 2018

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Wire feeders are intended to be used with power sources in MIG/MAG mode

only.

If used in any other welding mode, such as MMA, the welding cable between wire

feeder and power source must be disconnected, or else the wire feeder becomes

live or energized.

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions

when welding and cutting.

ELECTRIC SHOCK - Can kill

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet clothing

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.

EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to

EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your

body between the torch and work cables. Never coil the torch or

work cable around your body. Keep welding power source and

cables as far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes

• Use ventilation, extraction at the arc, or both, to take fumes and gases

away from your breathing zone and the general area

1 SAFETY

0463 387 201 -6- © ESAB AB 2018

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing

• Protect bystanders with suitable screens or curtains

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only

qualified people remove covers for maintenance and troubleshooting as

necessary. Reinstall panels or covers and close doors when service is

finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

CAUTION!

Class A equipment is not intended for use in residential

locations where the electrical power is provided by the

public low-voltage supply system. There may be potential

difficulties in ensuring electromagnetic compatibility of class

A equipment in those locations, due to conducted as well

as radiated disturbances.

NOTE!

Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment and its implementation

in accordance with national law, electrical and/or electronic

equipment that has reached the end of its life must be

disposed of at a recycling facility.

As the person responsible for the equipment, it is your

responsibility to obtain information on approved collection

stations.

For further information contact the nearest ESAB dealer.

1 SAFETY

0463 387 201 -7- © ESAB AB 2018

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

0463 387 201 -8- © ESAB AB 2018

2 INTRODUCTION

The wire feed units Warrior™ YardFeed 200 and Warrior™ YardFeed 200w are intended for

MIG/MAG (GMAW) welding together with welding power sources:

• Warrior 400i CC/CV

• Warrior 500i CC/CV

They come in different variants, see chapter "ORDERING NUMBERS".

The wire feed units are sealed and contains a four-wheel drive wire feed mechanism as well

as control electronics.

They can be used together with wire from ESAB, standard S200 Ø 200 mm / Ø 8 in.

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of

this manual.

3 TECHNICAL DATA

0463 387 201 -9- © ESAB AB 2018

3 TECHNICAL DATA

Warrior™ YardFeed 200

Mains voltage 42 V, 50-60 Hz

Power requirement 252 VA

Rated supply current I16 A

Settings data

Wire feed speed 1.9-25.0 m/min (75-985 in/min)

2/4 stroke 2 stroke or 4 stroke

Wire selection / Burnback Solid or Cored

Creep start Always on

Gas purging Yes

Wire inching Yes

Torch connection EURO

Wire bobbin: Type, Max. diameter S200, 200 mm (8 in.)

Wire dimension

Fe 0.6-1.2 mm (0.023-0.045 in.)

Ss 0.6-1.2 mm (0.023-0.045 in.)

Al 1.0-1.2 mm (0.040-0.045 in.)

Cored wire 0.8-1.6 mm (0.030-1/16 in.)

Weight

WYF 200 12 kg (26.5 lb)

WYF 200w 12.2 kg (26.9 lb)

Dimensions (l × w × h) 593 × 210 × 312 mm

(23.3×8.3×12.28in.)

Operating temperature -10 to +40°C (+14 to +104°F)

Transport and storage temperature -20 to +55°C (-4 to +131°F)

Shielding gas All types intended for MIG/MAG welding

max pressure 0.5 MPA (5 bar / 72.5 psi)

Maximum permissible load at

60% duty cycle 365 A

100% duty cycle 280 A

Enclosure class IP23

Standard factory settings

Standard factory settings for Warrior™ YardFeed 200 are in/min and fully open gas valve.

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or

cut at a certain load without overloading. The duty cycle is valid for 40°C(104°F).

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

4 INSTALLATION

0463 387 201 - 10 - © ESAB AB 2018

4 INSTALLATION

The installation must be carried out by a professional.

WARNING!

When welding in an environment with increased electrical danger, only power

sources intended for this environment may be used. These power sources are

marked with the symbol .

4.1 Lifting instructions

Andere Handbücher für Warrior YardFeed 200

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESAB Schweißsystem Handbücher

ESAB

ESAB Origo Arc 650c Bedienungsanleitung

ESAB

ESAB Caddy Tig 2200i AC/DC Bedienungsanleitung

ESAB

ESAB Origo Arc 406 Bedienungsanleitung

ESAB

ESAB Aristo RoboFeed 3004w Bedienungsanleitung

ESAB

ESAB Origo Mig C141 Bedienungsanleitung

ESAB

ESAB Renegade ET 180iP Bedienungsanleitung

ESAB

ESAB PCM-1125 Bedienungsanleitung

ESAB

ESAB Caddy Arc 151i Bedienungsanleitung

ESAB

ESAB ROGUE EM 140 Bedienungsanleitung

ESAB

ESAB Caddy Mig C200i Bedienungsanleitung

ESAB

ESAB Origo Tig 3000i Bedienungsanleitung

ESAB

ESAB SDE-100 Bedienungsanleitung

ESAB

ESAB 0700300989 Bedienungsanleitung

ESAB

ESAB CIGWELD CutSkill 60 Bedienungsanleitung

ESAB

ESAB Aristo Tig 4000iw Bedienungsanleitung

ESAB

ESAB PCM-500i Bedienungsanleitung

ESAB

ESAB Rogue EMP 210 PRO Bedienungsanleitung

ESAB

ESAB MIGMASTER 250 Bedienungsanleitung

ESAB

ESAB A6 Mastertrac Tandem Bedienungsanleitung

ESAB

ESAB Mig 325 Bedienungsanleitung

ESAB

ESAB PKB 250 Bedienungsanleitung

ESAB

ESAB MultiPower 460 Pulse Bedienungsanleitung

ESAB

ESAB Aristo RoboFeed 3004HW Bedienungsanleitung

ESAB

ESAB Origo Tig 3001i Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung