Escea ST900 Bedienungsanleitung

ST900

GAS FIRE USER GUIDE

www.escea.com

630289_0_Manual_User_ST900_AUS_NZ_R-emotion

NZ / AU

DO NOT PLACE ARTICLES OR FURNISHINGS ON OR AGAINST THIS

APPLIANCE.

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT

IS IN OPERATION.

PRIMARILY A DECORATIVE APPLIANCE - NOT CERTIFIED AS A SPACE

HEATER.

DO NOT MODIFY THIS APPLIANCE

DO NOT OPERATE THE FIRE IF THE GLASS HAS BEEN BROKEN, DAMAGED

OR IT IS NOT PROPERLY POSITIONED/HOOKED ONTO THE FIRE

DO NOT OPERATE THE FIRE WITH THE FASCIA PANELS REMOVED.

THIS APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR

INFIRM PERSONS UNLESS THEY HAVE BEEN ADEQUATELY SUPERVISED

BY A RESPONSIBLE PERSON TO ENSURE THAT THEY CAN USE THE

APPLIANCE SAFELY.

THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE

MANUFACTURERS WRITTEN INSTRUCTIONS.

The data plate for this appliance, containing technical information and

specifications, can be found to the right of the control tray, near the

base of the fire. To access this, the fascia must be removed.

Any installation or service work carried out on this appliance must only

be done by a recognised and qualified gas fitter.

Escea recommends the ST900 is inspected and serviced by a

qualified Gas Fitter once every twelve (12) months.

NZ LTD

17 Carnforth St, PO Box 5277

Dunedin, New Zealand

E-mail: [email protected]

Web: www.escea.com

Phone: +64 3 478 8220 Fax: +64 3 478 8221

IF APPLIANCE DOES NOT LIGHT AFTER 6 ATTEMPTS - PLEASE WAIT FOR 10

MINUTES BEFORE ATTEMPTING TO RELIGHT

THE GLASS SURFACE ON THE FRONT OF THE FIREPLACE IS CONSIDERED

A WORKING SURFACE, AND AS SUCH IS HOT AND CARE MUST BE TAKEN

NOT TO TOUCH THIS SURFACE. IT IS RECOMMENDED A SECONDARY

GUARD IS FITTED IN PLACES WHERE THERE ARE YOUNG CHILDREN OR

AGED OR INFIRM PERSONS.

CURTAINS SHOULD NOT BE POSITIONED ABOVE THE FIREPLACE AND ANY

PROTRUDING LEDGES MUST NOT COME WITHIN THE MINIMUM

DISTANCES SPECIFIED IN SECTION 5.1 OF THE INSTALLATION MANUAL

SUPPLIED WITH THIS APPLIANCE.

IF A GUARD IS FITTED TO THIS APPLIANCE TO REDUCE THE RISK OF FIRE

OR INJURY FROM BURNS AND NO PART OF IT SHOULD BE PERMANENTLY

REMOVED.

FOR PROTECTION OF YOUNG CHILDREN OR THE INFIRM, A SECONDARY

GUARD IS REQUIRED.

Basic Operation

Turning the ST900 on

Setting the Control Mode

Locking the Remote Control

Contents

Operation from the touch pad 5

Cleaning and Maintenance

Normal operating Sounds and Smells

Clearances

The ST900 electronic control system is designed to work within the

temperature range of 0°C to 70°C, with a humidity level that is non

condensing. This is to ensure safe operation of the electronic and

gas control system.

If the fireplace is subjected to an environment with temperatures

very close to or exceeding these temperature limits (irrespective of if

the fireplace is on or off at the time) the fireplace may not start up

until the temperature returns back to within the operating range.

To remedy this the environmental temperature should be addressed

and the fireplace control system given time to adjust accordingly.

The fireplace should then function correctly.

Basic Operation

The ST900 remote control allows you to turn ON and OFF the fire, control the

flame height in the Manual mode, or control the room temperature in the

Thermostat mode. The remote has a maximum range of 10 metres, and

because the remote works by radio frequency, it does not need to be aimed at

the for it to operate.ST900

When first powered the remote starts at the OFF screen (it is possible that the

remote is locked in the OFF screen: to unlock it just press the button below

Unlock, and then OK).

Switching on the ST900

Switching on: Once the remote is unlocked, press On (left button) and OK

(middle button). A beep from the control unit will be heard, and the ignition

process starts (the pilot will start sparking and gas will start flowing to the pilot,

which should then be lit within a few seconds

, after which the main burner will

ignite in HIGH flame mode

If the pilot flame fails to ignite, you must turn OFF the from the remote

and start the process of turning it ON again. BLOCKED ERROR will occur

after 5 ignitions within a 15 min period. This requires the control unit’s power

supply to be turned off for 15 seconds or you can wait out 15 minutes.

ST900

Wait until the current flame status displays HIGH

other action.

before performing any

Basic Operation 2

To turn off the fire, push the OFF button, to shut down the gas flow to the fire

and switch it off. The OFF display will now appear in the display.

Switching off the ST900

There are three different modes for controlling the appliance:

Setting the control mode for the fireplace:

Automatic mode allows you to set a temperature, while in manual mode the

flame level may be set to HIGH, MEDIUM, LOW & PILOT. Program mode

offers automatic temperature control for specific times of the day.

In the initial screen when the remote is turned on, three options are available:

AUTO, MANUAL and MENU.

Auto and Manual are two of the three different modes for controlling the

appliance with the remote.

If Manual is pressed, HIGH appears as the selected

setting. In the bottom row, ↓and ↑ appear,

indicating that the flame level can by changed by

just pressing the left or middle button. There are four

possible flame positions: Pilot flame, Low flame,

Medium flame and High flame. Pressing Back (right

button), returns to the initial screen. Note that a

Safety temperature can be previously set in the

configuration menu. This specifies the maximum

the maximum permitted room temperature. This

temperature can never be set higher than 40ºC

(104 ºF).

> Manual

> Automatic

> Program

Manual mode:

Basic Operation

If Auto is pressed in the initial screen, 25ºC (77 º F)

appears as the desired temperature in the selected

setting. In the bottom row, ↓ and ↑appear,

indicating that we can change the desired

temperature value by just pressing the left or middle

button. In auto mode the appliance heats until this

temperature is reached. Limits are 0-37ºC (32-

99ºF).

Pressing Back (right button), returns to the initial

screen.

Automatic mode:

In this mode the main burner can be switched on and off.

By default the program mode is not enabled. To enable program mode, enter

configuration mode by pressing and holding the OFF button for 40 seconds,

selecting “Programming” and selecting “yes” (For more information on

configuration mode see the installation manual, section 19.9).

There are two types of program mode: a Daily mode and a Weekly mode. In

the daily mode, every day uses the same program. In the weekly mode, every

day has its own program, so it is possible have a different program for each

day of the week.

In this mode the main burner can be switched on and off (pilot still burning).

Day programming menu: (Menu → Adjust Menu → Change Program)

Program mode:

There are 8 menus like this. One for Daily, and the others for each separate

day (Monday, Tuesday, Wednesday, Thursday, Friday, Saturday and

Sunday).

(Continued next page)

Basic Operation 4

The daily program screen consists of:

A: Selected (including “Daily”). The selected

day can be changed by pressing Change

(middle button).

B: Day schedule graphic. This bar displays

the program for the whole day by showing

the temperature setting for each hour of the

day. To access the day schedule graphic,

press ↓ (left button). To change the desired temperature, go to the hour you

want to change by pressing → (left button) and then press change (middle

button).

There are 3 temperature settings (bars):

Program mode (continued)

[Small bar] No temperature control (the appliance is in pilot

mode).

[Medium bar] The night temperature is set as the desired

temperature and the appliance will heat until this

temperature is reached. To adjust the night temperature

press “Menu → Adjust menu → Night” and set the desired

temperature.

[Large bar] The comfort temperature is set as the desired

temperature and the appliance will heat until this

temperature is reached. (High bar). To adjust the comfort

temperature pres Menu → Adjust menu → Comfort and set the

desired temperature.

Finally, to launch the program mode, in the main menu, set Program to On,

and select the desired Program Type (Daily or weekly). When activated, the

screen will show which of the above temperature settings is currently active,

Off, Night, or Comfort. The pilot must remain lit in order for the program to

remain running.

Go into Menu → Adjust menu → Unit. Press middle button and then left button

for changing units.

Changing the display from Celsius to Fahrenheit:

Off

Night Temp

Comfort Temp

Basic Operation

Operation from the Touch Pad

The touch pad is intended to be used for service/diagnostic purposes and to

operate the fire in the event that the remote handset becomes lost or inoperative.

If you remove the fascia you will find an electronic touch pad in the lower centre of

the fire. The touch pad features the basic operations of the fire: On, off, and

manual adjustment of the flame height.

DO NOT DROP THE REMOTE.

Dropping the remote may result in a cracked LCD screen or malfunctioning components.

The warranty does not cover damage to the remote sustained by dropping, however

replacement remote controls are available.

To Lock / Unlock the remote control buttons:

Go into Menu → Lock. Press middle button and then left button for locking the

remote.

To unlock pres left button and then middle button.

To turn on the ST900, push the ON/OFF button on the touch pad. The system will

emit a beep and begin the ignition process, which can take about 10 seconds.

Once the start up process is complete, the fire will be running in HIGH mode. The

ST900 is now in the 'Manual' mode and ready to be used.

While the fire is running, press the 'Flame Up' or 'Flame Down' button to alter the

flame height. The LED will flash once and the unit will beep to confirm the flame

height has been adjusted. The ST900 has 4 flame positions: Pilot only, Low,

Medium, and High flame height.

If the 'Flame Up' button is pressed while the unit is in the 'high' flame position, the

unit will emit 2 beeps. Similarly, if 'Flame Down' is pressed while the unit is in the

'pilot' flame position, .

To shut down the gas flow to the ST900, press the On/Off button and the LED will

blink and the unit will emit a beep.

the unit will emit 2 beeps

Clearances

Cabinet Clearances

There must be a minimum of 100mm from the sides of the fascia to any

protruding side walls or cabinetry.

Television Positioning Considerations

It is becoming common practice for consumers to mount flat screen TV's

above their gas fireplace.

Most TV manufacturers have specified in their instructions that the

TV should not be installed on, near or above a heat source. For this

reason TV location decisions rest solely with the householder and

the manufacturer / distributor will not be held liable for any adverse

affects on a TV located near to the ST900 fireplace that may be

caused by heat.

The drawings below are suggestions that may be used as a GUIDE

for those consumers who do decide to locate their TV above an

ST900 gas fire. These drawings show ways to reduce the amount of

warm air rising off the fireplace and onto the TV.

Andere Handbücher für ST900

Inhaltsverzeichnis

Andere Escea Kamin im Innenbereich Handbücher

Escea

Escea ST500 Bedienungsanleitung

Escea

Escea EF5000 Bedienungsanleitung

Escea

Escea EF5000 - AUS Bedienungsanleitung

Escea

Escea IB850 Bedienungsanleitung

Escea

Escea ST900 Bedienungsanleitung

Escea

Escea DX-Series Bedienungsanleitung

Escea

Escea IB1100 Bedienungsanleitung

Escea

Escea DX1000 Bedienungsanleitung

Escea

Escea DL850 Bedienungsanleitung

Escea

Escea EF5000 Montage- und Wartungsanleitung

Escea

Escea EF5000 Bedienungsanleitung

Escea

Escea ST500 Bedienungsanleitung

Escea

Escea DX-Series Bedienungsanleitung

Escea

Escea KS-Series Bedienungsanleitung

Escea

Escea DL850 Montage- und Wartungsanleitung

Escea

Escea DS 1900 Montage- und Wartungsanleitung

Escea

Escea IB1100 Bedienungsanleitung

Escea

Escea IB850 Bedienungsanleitung

Escea

Escea DF Series Montage- und Wartungsanleitung

Escea

Escea ST900 Bedienungsanleitung

Escea

Escea EF5000 Bedienungsanleitung

Escea

Escea ST900 Bedienungsanleitung

Escea

Escea NBS5525 Montageanleitung

Escea

Escea IB850 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung