Escort SRX Corvette C-6 Montageanleitung

SRX INSTALLED RADAR &LASER DEFENSE SYSTEM by ESCORT

SRX Corvette C-6 Installation Tips

We recommend bench assembling the entire system if you are a first time installer.

We also recommend reading the installation manual. Power can be applied and all

programming options selected on the bench or in the vehicle.

Power and Ground:

The fuse box is

locatedinthe

passenger’s foot well

againstthefirewall.

Locate a switched fuse

and tap into the hot leg.

Ground for power can

also be found on the Bose

amplifier case. Pull the

carpet back to expose the

fuse box. The interface

(Letter Code F on the

Installation Manual) will fit

in the cavity under the

Bose unit.

Note: the optional

amplified speaker will also

get power from this area.

Display Controller, Remote Mute / Volume Adjust, Amplified Speaker (Optional HV model),

Concealed Display (Optional HV model): All wires from these components will run from the

driver side. Feed the wires through the console to the passenger side where the interface is

located. The small opening in the console for the wires is located towards the rear of the

console. The space is large enough for all wires.

The

Display

Controller

(Code letter E on the installation manual) can be mounted on the lower dash to the right of

the steering wheel or buried under the dash or in the center console or anywhere on the HV

model after user preferences are

programmed if any. NOTE: If the

owner wants laser shifting enabled

this must be performed in

programming mode in the Bands

MOD selection by setting SHFT in

the LSR selection column after all

items are completely installed and

power is restored.

The Remote Mute Button (Code letter H on the installation manual) should be located

within easy reach of the driver. NOTE: This button has three functions – please consult the

owner’s manual for explanation.

The Bi-Colored Concealed LED Display (optional HV model) can be mounted in the

“crease” of the instrument

cluster and upper dash as

shown.TheLEDcomes

withatrimbezel–

a ¼ inch hole pulling the

LEDthroughandattaching

trim and snapping it back in

theholeinalmostany

locationthatisclearly

visible to the driver

willwork.

The Amplified Speaker (optional and required for voice alerts) can be zip tied to the wiring

harness under the dash with the speaker pointing toward the driver’s lower legs. Use the

knurled knobs as “anchors” for the zip tabs (tip: for even greater volumes such as needed in

convertibles, open T-tops, etc., the speaker can be mounted above the dash).

Front Laser Shifters: The Front Laser

Shifters (Code letter B on the

installation manual) can be mounted

different ways. They can be mounted

inside the grill area as on the

Yellow Z06 with the supplied mount

brackets and 3M Scotch VHB1double

sided tape (follow surface preparation

and temperature instructions for the

VHB tape),

or they can be mounted outside the grill using

VHB double sided tape as shown on the black

car.Spread the shifters as far apart as possible

but maintain a clear view of the road ahead. The

shiftersshouldbemounted as level as possible

(use the sight line on the short side of the shifter

as a level line) with the bubble lens on the top of

the front face. Remove the protective film from

the front face after installation. Feed the wires

towards the passenger side of the car under the

hood.

Front Radar Receiver: The Front Radar Receiver (Code letter A on the installation manual)

can be mounted inside the grill area using self taping hardware. Place the unit in the middle

and screw it to the plastic shroud. The unit can also be mounted inside under the hood

using double side tape and placed on the small ledge on the driver side as along as no

metallic parts obstruct the view forward (tip: do not mount radar receiver behind license

plate). The ledge is located behind the bumper.

Penetrating the Firewall: The wires from both front

shifters and the radar receiver should be run towards

the passenger side. The main wiring harness going

into the firewall will have a soft rubber boot around it.

You will need to disconnect and remove the battery

except on the Z06.

Take a small sharpened 1/8 inch metal rod and poke three holes through the rubber boot.

Cut the phone jack connectors off the wires and run thru the holes in the rubber boot.

13M VHB (Very High Bond) tape 4979F Black, 1 inch x 36 yard 62.0 mil. thick. Conformable foam, multi-purpose acrylic

adhesive, black, clear PE film liner, double sided. VHB tape can be ordered through any automotive paint supple outlet that

carries 3M automotive products.

This is much easier when taping the wires individually to the 1/8 inch metal rod and pushing

through. Once all wires are on the

other side of the firewall you will

need to cut the wires to length and

put new phone jack connectors on.

(Suggested replacement plugs and

the cut / crimper part numbers and

suppliers are noted on the

attached work instruction) Plug the

shifter wires into the supplied “Y”

connector and plug the Y-

connector and radar receiver into

the proper interface location.

Rear Laser Shifter: The Rear Laser Shifter is (Code letter G on the installation manual)

mounted to the rear license plate. Using a

factory supplied square hole and the

same 1/8 inch metal rod as before cut the

phone jack connector off and run wire

towards the factory rubber boot located on

the right side of the trunk area. You will

need to remove the carpet cover from the

rear panel on the right side on the back.

Use the same method as the front shifters

and run the wire thru the rubber boot. Run

the wire towards the front passenger side to the interface, cut the wire to length, attach a

new modular plug and plug the rear laser into the correct interface location.

Rear Laser Shifter properly installed -

Interface: Ensure all jacks

are plugged into the interface.

Use cable ties on the mute

switch and amplified speaker

jacks. Place wiring into the

cavity and cover everything

back up.

Once the unit is tested put all body and interior components back in place.

White

Orange

Blue

No wire

Step 4: Place modular plug with cable

into location as shown. Squeeze

handles together until they stop.

Step 1: Cut modular cable in crimp tool as shown.

Yellow

Red

Green

Blue

Crimping Too: Mouser Part Number 382-2094C

Mouser Electronics, Inc. Phone 800.346.6873

1000 North Main St. www.mouser.com

Mansfield, TX 76063

Important tips for cutting modular cables and crimping modular jacks

Step 3B: Color sequence of wires

placed in modular plug for Radar

receiver.

Yellow

Red

No wire

Blue

Step 3C: Color sequence of wires

placed in modular plug for Concealed

display.

Step 2: Place cable in strip part of crimp tool and rotate

wire in a circular direction to remove outside jacket. Be sure

not to knick the insulation on the separate strand of wire.

Step 3A: Color sequence of wires placed in modular plug for

front shifters, rear shifters, and display module.

Modular Connector Digi-Key PN A9091-ND 4 Pos / 4 Cont

Digi-Key Corporation Phone 800.344.4539

701 Brooks Ave South www.digikey.com

Thief River Falls, MN 56701

Inhaltsverzeichnis

Andere Escort Radarwarngerät Handbücher

Escort

Escort Passport 7500S TurboCharged Bedienungsanleitung

Escort

Escort Passport MAX Bedienungsanleitung

Escort

Escort Passport 9500i Bedienungsanleitung

Escort

Escort BELTRONICS GT-1 Bedienungsanleitung

Escort

Escort Shifter ZR3 Bedienungsanleitung

Escort

Escort Passport 8500 Bedienungsanleitung

Escort

Escort Passport SR1 Bedienungsanleitung

Escort

Escort SmartRadar Bedienungsanleitung

Escort

Escort PASSPORT 8500CI Plus Bedienungsanleitung

Escort

Escort Passport 8500 X50 Bedienungsanleitung

Escort

Escort Passport 8500 X50 Bedienungsanleitung

Escort

Escort Solo S3 Bedienungsanleitung

Escort

Escort Redline Ex Bedienungsanleitung

Escort

Escort Passport SR1 Bedienungsanleitung

Escort

Escort PASSPORT iQ Bedienungsanleitung

Escort

Escort Passport 8500 Bedienungsanleitung

Escort

Escort SmartRadar Bedienungsanleitung

Escort

Escort Passport MAX Bedienungsanleitung

Escort

Escort SOLO S4 Bedienungsanleitung

Escort

Escort PASSPORT S55 Bedienungsanleitung

Escort

Escort SmartCord Live Bedienungsanleitung

Escort

Escort ESCORT MAX Ci Bedienungsanleitung

Escort

Escort max 360c Bedienungsanleitung

Escort

Escort Passport 9500ix Bedienungsanleitung

Beliebte Radarwarngerät Handbücher anderer Marken

Cobra

Cobra XRS 9700 Bedienungsanleitung

Inforad

Inforad v3 Bedienungsanleitung

Cobra

Cobra ESD9200 Betriebsanleitung

Cobra

Cobra SPX 7800BT Bedienungsanleitung

Cobra

Cobra XRS 9940 Bedienungsanleitung

Lowrance

Lowrance LRA-2400 Bedienungsanleitung

Cobra

Cobra ESD-9160 Bedienungsanleitung

Whistler

Whistler CR80 Bedienungsanleitung

Stinger

Stinger VIP Bedienungsanleitung

Cobra

Cobra XRS 9430 Bedienungsanleitung

Cobra

Cobra Pro 9680 Betriebsanleitung

Whistler

Whistler 1655 Bedienungsanleitung

Radenso

Radenso Pro M-Edition Bedienungsanleitung

Rocky Mountain

Rocky Mountain RMR-D250 Bedienungsanleitung

Cobra

Cobra XRS 9645 Bedienungsanleitung

Cobra

Cobra XRS 9730 Bedienungsanleitung

Cobra

Cobra XRS 9775 Bedienungsanleitung

Whistler

Whistler SRT-30R Bedienungsanleitung