ESDEC Clickfit Evo Bedienungsanleitung
EN
MOUNTING SYSTEM FOR STEEL ROOFING
MANUAL
©ESDEC BV 2020
Rev. 30.0120
Mounting system for solar panels
on trapezoidal steel roofing
and corrugated steel roofing
portrait orientation
landscape orientation
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
CONTENTS
page
1. Introduction 1
2. General installation conditions 1
3. Product description 3
4. Parts overview 3
4.1 Exploded view mounting system in landscape orientation 3
4.2 Exploded view mounting system in portrait orientation 4
4.3 Parts list mounting system in landscape orientation 5
4.4 Parts list mounting system in portrait orientation 5
5. Mounting preparations 6
5.1 Tools and accessories check 6
5.2 Cleaning the roof 6
5.3 Determining and measuring position of solar panels 7
6. Installation mounting system in landscape orientation 8
6.1 Positioning the mounting profiles 8
6.2 Attaching the mounting profiles 9
6.3 Mounting the mounting rail cable clip optimizer ready and optimizer 10
(optional)
6.4 Mounting 1st solar panel on mounting profiles 11
6.5 Mounting other solar panels on the mounting profiles 12
6.6 Final assembly / multiple rows 13
7. Installation mounting system in portrait orientation 14
7.1 Positioning the mounting profiles 14
7.2 Attaching the mounting profiles 15
7.3 Mounting the mounting rail cable clip optimizer ready and optimizer 16
(optional)
7.4 Mounting 1st solar panel on mounting profiles 17
7.5 Mounting other solar panels on the mounting profiles 18
7.6 Final assembly 1st row of adjacent solar panels 19
7.7 Final assembly / multiple rows below each other 20
8. Attachments 21
8.1 Table 21
8.2 Mounting the mounting profile optimizer ready to the adapter profile 22
Corrugated steel roofing
THIS MOUNTING MANUAL SHOULD BE KEPT FOR FUTURE USE!
For the warranty period and terms, we recommend you contact your supplier. In addition, we would like to refer to our
General Terms of Sale and Delivery, which are available upon request.
The manufacturer cannot be held liable for damage or injury resulting from a failure to comply with this mounting
manual and a lack of general carefulness during transport, assembly and use of the mounting system. As a result of
our constant desire to improve, it is possible that the product differs from what is described in this manual in certain
details. For this reason, the instructions only serve as an installation guideline for the product described in this manual.
This manual was compiled with the utmost care, but the manufacturer cannot be held liable for any mistakes in this
manual or the results of these.
In addition, all rights are reserved and nothing in this manual can, in any way, be copied.
01
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
1. Introduction
This manual covers the installation of our mounting system for trapezoidal steel roong and corrugated steel roong (for
solar panels in landscape and portrait orientation).
Carefully read the manual, so you are fully familiar with its contents. Carefully follow the instructions in the manual. Always
perform actions in the right order.
Keep the manual in a safe and dry place. If the manual is lost, a new copy can be downloaded from www.esdec.com.
2. General installation conditions
General
A failure to comply with the regulations stated in this document may cause all warranty and product liability claims to become void.
The information, comments, and recommendations in this document are legally binding and users should check if they are complete and
up to date. Esdec BV reserves the right to adjust this document without prior notice.
Stability and condition of the roof
The roof should be in good condition and should have sufcient strength to bear the weight of the solar panels including any additional
materials, wind, and snow load. Check the stability of the roof and adjust the roof/construction if necessary. Always consult a contractor in
case of doubt. Make sure the reserve load capacity of the roof is not exceeded anywhere.
Safety warnings
• The assembly of the mounting system should be performed by qualied technical personnel (at least 2 skilled people).
• Adding or omitting parts can negatively impact the functionality and is strongly discouraged!
• Before placing the solar panels, the roof should be dry, clean, level and free of algae etc.
• Avoid assembly with strong winds or a slippery roof surface.
• On a sloping roof, always work with fall protection and, if necessary, with safety nets and edge protection.
• Note!: Never stand in the gutter.
• Wear shoes with reinforced toecaps and strong anti-slip soles.
• Always wear the appropriate protective clothing when performing work.
• Always use a lifting aid/lift installation when moving materials (solar panels etc.).
• Always place ladders on a sturdy, stable surface.
• Always place the ladder at an angle of about 75º and make sure it extends about 1 metre above the edge of the roof.
• If possible, secure the ladder at the top using a rope or lashing strap.
• Preferably comply with the manual “working safely on rooftops”.
Scope of application
• Solar panels of all brands and models with a frame height between 30 and 50 mm and a maximum size of about 2 x 1 m (± 2m2) per
solar panel.
• Wind zones 1 to 3, terrain category II and III. (NEN 1991-1-4).
• Roof height (3 - 15 m) If your roof is higher, you should contact your supplier.
• Roong type: Steel sheet
• Screws at minimum steel thickness: 0,5 mm, Rivets / blind rivets at steel thickness < 0.5 mm
• Roof slope: Between 15 - 60 degrees (35 degrees is optimal)
Edge zone
The distance between the solar panels and the ridge and gutter should be at least 30 cm due to the wind load.
The distance between the solar panels and the edge of the roof should be at least 30 cm. No solar panels can be placed in this zone,
either partially or completely.
Standards, regulations and legislation
During the installation of the mounting system, it is important to adhere to the mounting manual and the accompanying
standards to prevent accidents. Pay special attention to the following norms, regulations and legislation:
• Building Decree
• PBM Personal Protective Equipment
• KEMA Inspection of Electrotechnical Equipment
• DIN 1055 Design loads for buildings
• DIN 18299 General rules for all construction sectors.
• DIN 18451 Scaffolds
Removal and dismantling
Dispose of the product in compliance with local laws and regulations.
Warranty
Warranty according to the terms of warranty and the terms and conditions of Esdec BV. These can be found on the website
www.esdec.com
Liability
The manufacturer shall not be held liable for any damage or injury caused by a failure to (strictly) comply with the safety
regulations and instructions in this manual or due to carelessness during the installation of the product described in this
document and any accessories.
• printing errors reserved
02
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
3. Product description
The mounting system is made of mounting proles and the required mounting materials to mount the solar panels in
landscape or portrait orientation on the trapezoidal or corrugated steel roof.
The mounting system for steel sheet roong can be used for all steel roofs, including the common corrugated or trapezoidal
steel roofs. (The sheet steel thickness should be at least 0.4 mm.)
Roof attachment
The mounting proles are attached to the steel sheet using self-tapping screws or blind rivets. Note! There are two options:
a high (Optimizer ready) or low (Basic) mounting prole. In this manual, the high mounting prole is shown by default. The
height of the mounting prole does not have any consequences for the required parts, with the exception of the optional
cable clip optimizer ready and optimizer. These can only be used for the high mounting prole. The high mounting proles
have a notch that functions as a point of reference when aligning the proles.
Because the mounting proles are not attached to the rafters or purlins, the position of the solar panels on the roof can be
selected freely.
The mounting proles have EPDM sealing tape at the bottom, which serves as a water barrier. In case of corrugated steel
roofs, the mounting proles are provided with an optional EPDM adapter prole.
Attachment of the panels
The solar panels are attached to the mounting proles using universal module clamps.
4. Parts overview
4.1 Exploded view mounting system in landscape orientation
03
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
1
2
6
6
4
5
5
6
7
2
2A
3. OPTIONAL:
in case of corrugated
steel roofing
4.2 Exploded view mounting system in portrait orientation
04
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
1
5
4
2
5
65
6
7
2
2A
1. Solar panel
2. Mounting prole steel roof ‘Optimizer ready’
landscape
Product no.: 100-8050
6B. Module Clamp Universal black
Product no.: 100-8020-B
5B. End clamp support black
Product no.: 100-8065-B
4.3 Parts list mounting system in portrait orientation
05
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
4. Self-tapping screw 6.0x25mm
Torx 30
Product no.: 100-8080
4.4 Parts list mounting system in portrait orientation
1. Solar panel
2A. Mounting prole steel roof ‘Basic’ portrait
Product no.: 100-8049
6B. Module Clamp Universal black
Product no.: 100-8020-B
5B. End clamp support black
Product no.: 100-8065-B
4. Self-tapping screw 6.0x25mm
Torx 30
Product no.: 100-8080
2A. Mounting prole steel roof ‘Basic’
landscape
Product no.: 100-8048
3. EPDM adapter prole corrugated steel roof
‘Optimizer ready’ landscape
Product no.: 100-8082
*optional
3A. EPDM adapter prole corrugated steel
roof ‘Basic’ landscape
Product no.: 100-8081
*optional
7. Mounting rail cable clip
‘Optimizer ready’
Product no.: 100-8062
*optional
2. Mounting prole steel roof ‘Optimizer
ready’ portrait
Product no.: 100-8052
7. Mounting rail cable clip
‘Optimizer ready’
Product no.: 100-8062
*optional
5. End clamp support grey
Product no.: 100-8065
6. Module Clamp Universal grey
Product no.: 100-8020
5. End clamp support grey
Product no.:100-8065
6. Module Clamp Universal grey
Product no.: 100-8020
5. Mounting preparations
5.1 Tools and accessories check
T30
Scaffold or stable,
safe ladder
The following is a list of the required tools / aids:
Marker / crayon Brush Tape measure Battery drill
Metal saw Safety gloves
06
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
5.2 Cleaning the roof
Clean the steel roof sheets with a brush.
Remove algae, moss etc. to reduce unevenness during the installation to a minimum!
Safety helmet Safety glasses
Safety clothing Face mask Hearing protectionSafety clothing
5.3 Determining and measuring position of solar panels
When determining the position of the solar panels on the sloped roof, it is very important to pay attention to the position of
the sun during the day and the entire year. Place the panels on a roof surface that has a minimum amount of shade. Shade
from a chimney, dormer, tree or adjacent building negatively impacts the yield of the solar panels. We strongly recommend
using the optimizer here.
Measuring and demarcating
In order to place the solar panel (in landscape or portrait orientation) you need a space of about 160x80 cm or 160x100cm
or 200x100cm per panel. (depending on the type of solar panel)
Make sure there is a space of at least 30 cm around the solar panels on the roof. This means 30 cm away from the ridge
and gutter and 30 cm away from the sides because of turbulent wind load.
Mark the contours of the panels and the eld on the steel sheets with a marker or crayon.
Demarcation for landscape orientation:
Mark the contours of the panels and the eld on the steel sheets with a marker or crayon. Draw lines where the mounting
proles will be: (see chapter 6.1). The high mounting proles have a notch, making it easy to align the proles. (view Detail
A in illustration below)
Follow the instructions of the calculator for the distance between the mounting proles. These instructions prevail.
Demarcation for portrait orientation:
Draw lines where the mounting proles will be: (see chapter 7.1). Follow the instructions of the calculator for the distance
between the mounting proles. These instructions prevail.
07
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
min. 30 cm
min. 30 cm
min. 30 cm
min. 30 cm
A
min. 30 cm
min. 30 cm
min. 30 cm
min. 30 cm
Notch for alignment
A
B
Clamp range by module
specified by manufacturer
The calculator prevails when
it comes to the number of screws.
(see table in attachment)
A
B
180
40
40
40
6. Parts list mounting system in landscape orientation
08
Rev. 30.01.20 MANUAL MOUNTING SYSTEM FOR STEEL ROOFING
6.1 Positioning the mounting profiles
Note! In case of a corrugated steel roof, the mounting prole steel roof ‘Optimizer ready or Basic’ landscape should be
equipped with an EPDM adapter prole on the bottom (see chapter 8.2 in the attachment).
You can determine the position of the mounting proles based on the location of the solar panels on the roof.
The mounting proles should be positioned at distance B in the upwards direction of the steel roof. The mounting proles
should be positioned at distance A in the horizontal direction of the steel roof. Distribute the mounting proles (per panel)
widthways parallel to the line where the solar panels will be.
Note! Make sure the mounting proles are separately aligned.
Note! The calculator prevails when it comes to the number of screws per mounting prole (see table in attachment).
Note! In the instruction, Mounting prole steel roof ‘Optimizer ready’ landscape is used.
Basic
Landscape
Optimizer ready
Landscape
Product no.: 100-8048 Product no.: .100-8050
Andere Handbücher für Clickfit Evo
7
Inhaltsverzeichnis
Andere ESDEC Solarpanel Handbücher
