ESI LEDG2 Series Kurzanleitung

INSTALLATION AND USE

LEDG2

Under Cabinet Light

LEDG2 Rev A 4/17 Multiple Unit Models:

LEDG2-24X2-SLV

LEDG2-24X3-SLV

LEDG2-24X4-SLV

LEDG2-36X2-SLV

LEDG2-36X3-SLV

Model LEDG2-24-SLV

Model LEDG2-36-SLV

LEDG2

PLEASE REVIEW these instructions before beginning the installation. Check that

all parts needed were provided with your order. Contact your supplier if any

operates to your satisfaction.

PARTS PROVIDED

Light Fixture (1)

20" or 25"

Mounting Clip (2)

NOTE:

Orders of multiple unit models include one 24" jumper cord

for each additional light.

Cord Clip (2)

Power Supply (1)

Diffuser (1)

Flathead Screw (2)

#8-32x1

ADDITIONAL TOOLS REQUIRED (if screw mounting)

• Power Drill • 1

/8" Phillips Screw Driver Bit

Specifications

• Two lengths: 24", 36" (nominal)

• Color temperature: 3500K

• Power consumption: 24"=11W, 36"=14W

• CRI: 85

• Lumens (with Diffuser): 24"=550, 36"=740

• Lumens (w/o Diffuser): 24"=430, 36"=580

• Lamp life: 50,000 hours

• Continuous dimmer

• 9 ft. power cord

• Occupancy sensor available

See IMPORTANT SAFETY PRECAUTIONS on page 6.

CAUTION:

This install requires a

power drill. This is not

a hand tool install.

• #2 Phillips Screw Driver Bit

LEDG2

STEP 1: Choose a Mounting Method

• The LEDG2 light xture may be installed under the cabinet in one of two

ways:

— Magnet attachment (if the bottom of the cabinet is a steel surface).

— Mounting with screws.

• Review STEPS 2A and 2B to decide which method is most appropriate for

your installation.

STEP 2A: Attach the Light Fixture Using Magnets

• The two mounting clips have very strong magnets built into them.

• Snap one mounting clip onto each end of the xture, with the magnet side

facing up.

• Attach the xture to the steel surface.

— Hold the xture on the outside ends and move it slowly into position.

— Take care not to allow your ngers to come between the xture and the

steel surface during installation.

Proceed to STEP 3 on page 5.

Mounting

Clip

Mounting

Clip

Fixture

Magnet

LEDG2

STEP 2B: Attach the Light Fixture Using Screws

This method is used with wooden cabinets only. Check that the 1

/2" wood

screws will not go all the way through the underside of the cabinet.

• Mark pilot hole locations on the underside of the cabinet.

— Mark hole locations 191

/8" apart with model LEDG2-24 or 241

/8" apart with

model LEDG2-36.

• Drill 1

/8" pilot holes in the marked locations.

CAUTION: Be careful not to drill all the way through the underside of the

cabinet.

• Attach the mounting clips with the 1

/2" wood screws.

• Snap the light xture into the mounting clips.

Proceed to STEP 3 on page 5.

LEDG2

STEP 3: Connect the Power Supply

• Plug the jack from the power

supply into the light xture.

— The jack can be plugged

into either end of the light

xture.

— The unused end can be used for connecting power to another unit using

a jumper cord in a daisy-chain conguration.

— With model LEDG2-24, up to four units can be daisy-chained. With model

LEDG2-36, up to three units can be daisy-chained.

• Plug the power supply into a standard 115VAC outlet.

STEP 4: Attach the Diffuser, If Desired

• The diffuser is magnetically attached to the light xture. Simply position it

over the LED strip.

• Detach the diffuser by pulling it downward.

STEP 5: Operate the Light

• Tap the switch to jump to maximum

brightness, or to power off.

• Press and hold the switch to cycle

through all brightness levels.

From

Power

Supply

Diffuser

LEDG2

STEP 6: Manage the Power Supply Cords and/or Jumper Cords

• Adhere cord clips to the underside of

the cabinet and other surfaces as

needed to organize the cords neatly.

IMPORTANT SAFETY PRECAUTIONS

Read all safety precautions and installation instructions carefully before installing

or servicing this fixture. Failure to comply with these instructions could result in

potentially fatal electric shock and/or property damage.

If wiring is required, it is recommended that a qualified electrician perform all wiring.

This fixture must be wired in accordance with all national and local electrical codes.

Do not handle any energized fixture or attempt to energize any fixture with wet

hands or while standing on a wet or damp surface or in water.

Make sure the power source conforms to the requirements of the fixture.

Protect the power cord from coming into contact with sharp objects, oil, grease,

hot surfaces, or chemicals. Replace or repair damaged or worn cords immediately.

This fixture is intended for general indoor lighting only.

Cord Clip

Cord

800.833.3746esiergo.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESI Beleuchtungsausrüstung Handbücher

ESI

ESI Amble Classic Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung