ESL Spectrum Series Bedienungsanleitung

KONEX USER GUIDE

KONEX CONTROL SYSTEM

2020

KONEX USER GUIDE

FCC COMPLIANCE

OTHER INFORMATION

AUDIENCE

SAFETY PRECAUTIONS

WARNING–RISK OF ELECTRICAL SHOCK WARNING–RISK OF INJURY

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Important note: No change to the antenna or the device is permitted. Any change to the antenna or the device could void user’s

authority to operate the device and result in the device exceeding the RF exposure requirements.

Product information is subject to change without notice. Check the ESL Vision website for the latest information.

All trademarks are recognized as the property of their respective owners.

To ensure optimal reliability and to meet warranty requirements, Spectrum and Konex products must be installed according to the

instructions in this manual and the enclosed instructions included with each component.

This manual is intended for use by skilled professional installation and maintenance personnel familiar with State and Local codes.

Safety and shock hazards may be present during installation.

It is important to read, understand and follow the instructions provided with each component. Failure to follow all safety precautions

and instructions may result in property damage or serious injury.

• Disconnect or turn o power before installation or

servicing.

• Verify that supply voltage is correct.

• Make all electrical and grounded connections in

accordance with the National Electrical Code (NEC)

and any applicable local code requirements.

• Wear gloves and safety glasses at all times when

removing luminaire from carton, installing, servicing

or performing maintenance.

• Avoid direct eye exposure to the light source while

it is on.

Important Safety Information

READ THIS FIRST

This manual contains important instructions for use during installation, operation and maintenance of ESL Vision’s Spectrum and

Konex enabled light ﬁxtures and controls.

KONEX USER GUIDE

Table of Contents

Important Safety Information

Read This First ...............................2

Overview

What is Spectrum.............................4

What is Konex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

How it Works ................................5

Available Components ........................6

Konex Control System Planning

Develop an Installation Plan ...................7

System Installation

Physical Installation ...........................9

App Installation ............................. 10

Commissioning Components with App ..........11

Gateway Installation

What is the Gateway? ........................ 14

Gateway Setup.............................. 14

App Operation

Navigating the App .......................... 15

Devices .................................... 16

Groups.....................................20

Grouping Diagrams ..........................22

Scenes.....................................23

Schedules ..................................24

Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Alerts ......................................25

Account ....................................25

Reports ....................................25

About......................................25

Energy Monitoring

Monitoring and Reporting ....................26

Daily Operation and Maintenance

Daily Operation .............................26

Internet Outage .............................26

Glossary

Common Terms .............................27

Iconography ................................27

Troubleshooting

Helpful Resources ...........................28

Procedures .................................28

Frequently Asked Questions ..................30

Appendix

Installation Map ............................. 31

Master Component List ......................32

Master Component List ......................33

KONEX USER GUIDE

Overview

WHAT IS SPECTRUM

ESL Vision is an industry leader in lighting technology and product innovation. Raising the bar once again, ESL introduces the most

intuitive network lighting system on the market with Spectrum and Konex.

The Spectrum Series is a cutting-edge family of wirelessly controlled ﬁxtures that are both wattage adjustable and kelvin tunable.

Spectrum oers an incredible kelvin range of 2700K–6500K, ensuring that end users will have their preferred light output on every

project and is easily changed using the ESL Network Lighting App.

WHAT IS KONEX

Konex is a family of maintenance-free occupancy sensors, photocells and switches that are code compliant and maximize energy

savings. Operate a single ﬁxture or a group of ﬁxtures wirelessly using the ESL Network Lighting App. All Spectrum Series ﬁxtures

have Konex capabilities built in, to ensure that your lighting system will work seamlessly.

KONEX USER GUIDE

Group Fixtures for Easy Control

of Rooms or Large Areas

Wirelessly Connect Optional Occupancy Sensors, Photocells

and Switches for Complete Network Control

Occupancy Sensors Photocells Switches

HOW IT WORKS

Spectrum Series ﬁxtures and Konex controls are equipped with Bluetooth Mesh Technology which allows them to communicate

wirelessly with the ESL Network Lighting App. Create groups, automated scenes and even timed schedules to simplify operation

and maximize eciency.

KONEX USER GUIDE

AVAILABLE COMPONENTS

LIGHTING FIXTURES

The Konex Control System can be fully customized with a variety of ﬁxtures and sensors to meet the lighting requirements of any

space.

Learn more about all of ESL Vision’s product lines online at www.eslvision.com.

Spectrum oers a variety of ﬁxtures and retroﬁts to update any space with energy

saving, state of the art lighting.

MOTION SENSORS

Reduce wasted energy and increase safety by

lighting areas only when motion is detected. IP65,

PIR and Microwave sensors are available.

POWER PACKS

Retroﬁt any existing LED ﬁxture to have dimming

and network capabilities.

EMERGENCY

External emergency drivers provide up to 90

minutes of backup power. *Only available for

factory installation.

DAYLIGHT HARVESTING SENSORS

Maintain consistent lighting levels and reduce

energy consumption.

GATEWAY

Adding a gateway allows for schedule creation

and consumption reporting.

SWITCHES

Wireless switches are battery operated and used

for simple on/o operation, dimming, or can be

programmed to run custom scenes.

KONEX USER GUIDE

Konex Control System Planning

DEVELOP AN INSTALLATION PLAN

DEFINE THE FUNCTIONALITY

It is important to deﬁne the system features and functions that will be needed for regular operation. Decisions to be made about

the requirements for each area could include:

It is best to create a map for your system to start this process (Figures 1, 1b). It will simplify the procedure to create your network

lighting system and will be used for the entire installation and commissioning operation. Include a layout of where ﬁxtures, sensors

and switches will be located. Appendix 1 outlines some methods for creating the map.

The maximum recommended space between each component is not to exceed 60 feet with structural obstructions or 150 feet

with a clear line of sight.

• Individual fixture control vs group/room level control

• Motion sensing requirements

• Photocell/Daylight Harvesting requirements

• Define grouping for switches and sensors

• Defining scenes

• Decide who will be maintaining the system and will have access to the ESL Network Lighting App

• Determine the regulatory and utility program compliance requirements

• Spacial considerations of each space

Creating an installation plan will provide a blueprint for your Konex Control System and help mitigate the time required for full

commissioning and set up within the ESL Network Lighting App.

Proper planning of your system will insure smooth installation, simpliﬁed and quick commissioning, and seamless operation of your

new Konex Control System. Be prepared to spend a day to review this manual and familiarize yourself with how to operate the ESL

Network Lighting App. The following guidelines will help with this process.

Figure 1b. Warehouse installation map with lighting layout

Figure 1. Oce ﬂoor installation map with lighting layout

Use simple symbols when labeling the devices to make it

easy to read/reference during installation:

Fixture Motion

Sensor

Photocell Switch

KONEX USER GUIDE

COMMISSIONING PLAN

It is essential to deﬁne a workﬂow prior to commissioning the devices, especially with large system installations. General good

practice will involve learning devices group by group in one room or area at a time.

Divide the ﬂoor plan into groups that will make sense for

usage. (Figure 2) This is typically one room or area per group

or function. Large spaces such as warehouses might be

grouped by aisle. (Figure 2b) Fixtures that will not be part of

a group should be marked as such. If multiple groups are

dedicated to a single switch, indicate the scene as well.

Naming conventions should be decided at this time to make

it easier to ﬁnd ﬁxtures and groups when the entire system is

operational. For example, you may name a group “Workroom”

with sub groupings named “Workroom-a”, “Workroom-b”,

etc. The ﬁxtures within these groups could be called “WR1”,

“WR2”, etc. Keep in mind that names can easily be changed

later. Make a list of ﬁxture and control names along with the

associated group using the Component Master List Appendix

2 as illustrated in Figure 3.

Figure 3. Example Component Master List

NETWORKS AND LIMITS

There is no limit to the number of components that can be added to the Konex Control System. For large projects of 1,000 ﬁxtures

or more, structuring the system into networks creates a more manageable way to locate individual ﬁxtures and maintain the

system. For such systems, networks could be made for each building, ﬂoor, operation or department.

When creating the Installation Map and Master Component List, make sure that each network is clearly deﬁned.

Figure 2b. Warehouse installation map with outlined groups (orange)

and scene (pink)

Figure 2. Oce ﬂoor installation map with outlined groups (orange)

Maintain account control even when employees move on: Creating a company controlled email account for the end user’s

lighting system (S[email protected]) will simplify account use by the end user and ensures that when employees

leave, network access is not lost with them.

KONEX USER GUIDE

System Installation

PHYSICAL INSTALLATION

PARTS REQUIRED

INSTALL SYSTEM COMPONENTS

INSTALLATION CONSIDERATIONS

COLLECTION OF QR CODES

• ESL Network Lighting App installed on an Android mobile device with Bluetooth capabilities.

• Fixtures, sensors and switches as deﬁned in the installation plan.

• Optional Gateway for remote access and metering capabilities.

Following the Installation Map and Master Component List created in the planning process, install the ﬁxtures and other components

according to the installation instructions included with each.

For smaller systems comprising of fewer than 50 components, it is recommended to install the ﬁxtures and controls for one room

or group, restore power, and commission the ﬁxtures with the app before moving on to the next room or group.

In the case of large systems, the installation of all components should be completed and then selectively restore power to areas/

groups for commissioning.

In either scenario, it is important to use the Installation Map and Component Master List to systematically commission the network

and be sure to retain the QR codes attached to each component. Best commissioning practices will include the scanning of QR

codes and naming each component prior to powering on and learning the components via Bluetooth.

All components have a QR code sticker that will identify them. As they are being installed, these stickers should be removed and

placed in a predetermined location for later use. The codes will be scanned to rename and group the components in accordance

to the Installation Map and then placed on the Master Component List for future reference.

Installation of the Konex Control System should be completed by a qualiﬁed electrician following all building codes and safety

procedures. AC powered components used are installed in the same manner as traditional lighting components. Please refer to

the installation instructions included with each component.

System installation will comprise of the physical installation of the Konex Control System devices, commissioning and grouping the

devices using the ESL Network Lighting App and setting up additional functionality such as scenes and schedules.

In order to avoid overloading the app when learning components with Bluetooth, it is important to only have 50–100

non-commissioned ﬁxtures powered on at a time. Once components have been learned in using Bluetooth it is not

necessary to cut the power in order to add more.

KONEX USER GUIDE

APP INSTALLATION

INTERNET CONNECTION

User accounts for the ESL Network Lighting App are stored and synchronized by utilizing the AWS cloud by Amazon which oers

the utmost in security and stability. Reliable internet access and WiFi must be available to create and access accounts, as well as

to commission the Konex Control System by both a mobile device and the Gateway.

There is a risk of data loss and commissioning errors if the internet connection is not stable. In the case that reliable internet is

unavailable or is unstable, the use of a dependable portable hot spot is recommended.

Commissioning and operation of the Konex Control System is completed by using the ESL Network Lighting App.

CREATE ACCOUNT

Open the app and select CREATE

ACCOUNT to create new credentials.

While either a mobile number or email

can be used to create an account, it is

highly recommended that an email that is

linked to the end user is used instead of a

mobile phone number.

Make sure to only use information for the

end user and not the installer, as this set

up for the account cannot be changed.

A veriﬁcation code will be sent to the entered

email or mobile. Enter the code to complete

the account creation.

You are now ready to start learning in ﬁxtures

and controls.

INSTALL ESL NETWORK LIGHTING APP

Download and install the ESL Network Lighting App on any current Bluetooth equipped Android device from Google Play.

When scanning QR codes, the information is only stored on the scanning device prior to learning with Bluetooth. If multiple

mobile devices are used to commission a network at the same time, it is possible to incorrectly conﬁgure devices or

encounter commissioning errors which may require re-commissioning and/or the possible need to reset the ﬁxtures.

For this reason, it is recommended that commissioning with the app is completed by using only one mobile device per

network in accordance to the Installation Plan and Component Master List.

It can not be stressed enough that the account MUST be created using the END USER’S email (IE:

[email protected]). Once components have been commissioned, it is not possible

to change the user name or move the system to a dierent account.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESL Arbeitsleuchte Handbücher

ESL

ESL ESL-EMG-2DC Series Bedienungsanleitung

Beliebte Arbeitsleuchte Handbücher anderer Marken

ANSMANN

ANSMANN POWERLIGHT 5.1 Bedienungsanleitung

RTRMAX

RTRMAX RTX1868 Bedienungsanleitung

FeinTech

FeinTech LAL00220 Bedienungsanleitung

Bunker Hill Security

Bunker Hill Security 64735 Bedienungsanleitung

Goobay

Goobay 30450 Bedienungsanleitung

REV Ritter

REV Ritter SPOT Bedienungsanleitung

Ignition

Ignition Stagepix Line 100 IP Bedienungsanleitung

SCANGRIP

SCANGRIP DUO CONNECT Bedienungsanleitung

Bosch

Bosch GLI 18 V Bedienungsanleitung

Bayco

Bayco SL-1514 Bedienungsanleitung

EUFAB

EUFAB SMD LED 8+1 Bedienungsanleitung

DeWalt

DeWalt DCL510 Bedienungsanleitung

PowerSmith

PowerSmith PWLD080T Bedienungsanleitung

MaxLite

MaxLite 73683 Bedienungsanleitung

Heitronic

Heitronic Trend 27867 Bedienungsanleitung

Monzana

Monzana Gore MZCL10 Bedienungsanleitung

EINHELL

EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung