ESP PTZCON Bedienungsanleitung
PAN, TILT AND ZOOM CONTROLLER
USER MANUAL
PTZCON
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 1
2
Produ t Overview
FEATURES
• Supports up to 255 PTZ cameras
• Multiple protocols and baud rates supported across multiple PTZ cameras
• LCD display
• Control lock feature to deny unauthorised use
• Supports Pelco-D, Pelco-P, Samsung, Panasonic and HikVision protocols
• Supports baud rates 1200, 2400, 4800, 9600, 19200
INSTALLATION OVERVIEW
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 2
3
Installation
t is highly recommended that a screened cable
is used to connect the RS485 control wires
from PTZ controller, or interference may occur.
1. Connect Ta to the RS485+ on the PTZ camera(s)
2. Connect Tb to the RS485- on the PTZ camera(s)
3. Connect GND to the ground on the PTZ camera(s) if applicable
4. Connect the cable screen to GND
5. Set camera protocol(s) and baud rate(s)
KEYBOARD OVERVIEW
Button(s) Function
Define a preset camera position
Record new movement pattern (will directly mimic user input)
Set up a patrol route based on preset camera positions
(positions must be defined by the user)
Turn auxiliary PTZ controllers on or off
Select PTZ camera D
(select a PTZ D to control the associated camera)
Recall preset position
Recall pattern
Recall patrol
Set camera to auto pan mode (perimeter scan)
Adjust camera focus
Adjust camera zoom
Close/open camera iris (for non-auto iris cameras)
Menu/Esc button for navigating setup menu & key lock
Show protocol and baud rate for current PTZ D
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 3
4
Keyboard Fun tions
PLEASE NOTE
Availability of some features will depend on compatibility and specification of your PTZ
camera. Some controller functions may not be supported by your PTZ camera, please
check with the product manufacturer.
MENU/SETUP KEYS
Menu: Hold for 3s to enter setup/configuration menu.
Enter password (default 8888) See page 5 for further details.
Back: Escape to previous menu/exit menu.
Press once during normal operation to lock keys (will not work in menu).
Show protocol and baud rate
for current PTZ D.
FUNCTION SET KEYS
To store a preset camera position,
press (0-255)+[Preset].
To record a predefined movement pattern, press for 3s. All camera movements will
be recorded exactly as per user input. Press again to stop recording.
To set up a patrol points at preset camera positions, presets must be defined first
(see Preset button).
Press [Patrol], choose the first preset position (0-255) then push joystick
downwards to choose dwell time (0-255) then push joystick downwards to select
movement speed (0-99), and push the joystick downwards to setup the next point
in the patrol.
Once all points in the patrol have been set, press [Patrol] +
Function
set keys
Function
recall keys
Camera
control keys
Menu/setup keys
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 4
5
FUNCTION RECALL KEYS
To recall a specific preset camera position, press (0-255) + [Shot]
Press to run recorded pattern.
To recall a specific patrol tour, press (0-255)+[Patrol]
Configuration menu
To enter menu press for 1s then enter password (default 8888)
Use the joystick up/down to navigate through menu tree
Use the joystick left/right to alter the current value where applicable
Press to confirm/select, press to escape/go back
Menu Item Explanation
SET PW Set 4-digit P N to lock keypad
DEFAULT Restore factory default settings
SOUND SET Key tones on/off
D SET Set keyboard D (when using multiple controllers)
LOCK SET Toggle key lock on/off
ADDRESS Sets protocol and baud rate for each PTZ camera.
Push joystick left/right to select camera D then press
Push joystick up/down to change between protocol/baud rates,
push joystick left/right to alter values. Press to confirm.
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 5
6
Key Lo k Fun tion
Key lock must be enabled from the menu (see page 5)
Key lock can only be engaged if not in setup menu.
Press then enter password P N to lock keyboard. Repeat process to unlock.
To reset a lost password, please call ESP Technical Support on 01527 51 51 50.
Warnings
Do not disassemble product, warranty will become void.
Only for use indoors in environments <95% humidity
Only use the supplied 12V PSU
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 6
7
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 7
Elite Se urity Produ ts
Unit 7, Target Park, Shawbank Rd
Lakeside, Redditch B98 8YN
Telephone: 01527 51 51 50
Fax: 01527 51 51 43
email: [email protected]om
Te hni al Spe ifi ations
Protocol Pelco-P, Pelco-D, Panasonic, HikVision,
Samsung, RULE, Dahua, SAE
Baud ratebps1200, 2400, 4800, 9600, 19200
Max camera support 255
Controllers supported 16 in total (15 auxiliary)
Power supply DC 12V±10%
Power consumption 6W MAX
Working temperature 0°C-50°C
Dimension 420 x 260 x 170mm
PTZCON Manual_Layout 2 18/03/2014 09:26 Page 8
Inhaltsverzeichnis
Andere ESP Controller Handbücher
