ESX VISION ANDROID Series Bedienungsanleitung

V1.0

INSTALLATION

GUIDE

VISION ANDROID™ SERIES

SMART NAVICEIVER

MOBILE INTERNET READY

VN940-RM-4G

INCL. START-UP INSTRUCTIONS,

CAMERA SETTINGS,

GPS RECEPTION, 4G/LTE

and much more.

SCOPE OF DELIVERY

ITEM FIGURE QUANTITY

Main device

Art. No. VN940-4G 1

Mounting frame for

Renault Master incl. 4 screws

Art. No. VNA-EB-RM20-1DIN

System cable set

with CAN bus module

for Renault Master

(20-pin plug)

Art. No. ZEOS-A11764-022

AV cable set 1

with audio and video

connections

incl. rear view camera

(14-pin plug)

Art. No. ZERW-120014-207

USB port 1

(4-pin plug)

Art. No. ZECL-290004-217

4G/LTE dongle

(6-pin plug)

Art. No. ZESW-012900-004

Adapter cable for

factory USB port 2

(8-pin plug)

Art. No. ZECL-29008-213

ITEM FIGURE QUANTITY

AV cable set 2

with power, audio and video

connections,

additional camera input

(8-pin plug)

Art. No. ZERW-120008-210

Y-adapter for the external

microphone and the receiver

of the separately available

remote control

(6-pin plug)

Art. No. ZERW-121506-200

GPS antenna

Art. No. ZESW-011701-007 1

External microphone

(Mini jack)

Art. No. ZECL-035201-330

4G/LTE antenna

Art. No. VNA-LTE 1

SCOPE OF DELIVERY

WIRING DIAGRAM

Radio antenna plug from vehicle (FM/AM)

4G/LTE antenna

GPS antenna

WiFi antenna

Optical stereo

audio output (S/PDIF)

Fuse 10 A

20-pin system socketInputs for

AV cable sets

E F G H

B C D

SSystem cable set with CAN bus module (20-pin connector, black)

After plugging the 20-pin black connector into the Naviceiver, you need to connect the other

ends (white) to the vehicle’s system connectors (white).

Cable black/white (KEY2): Not in use

RCA yellow (CAM OUT): Not in use

Cable blue (ANT)*: Turn-on signal for electric antenna(+12V)

Cable orange (AMP CON)**: Turn-on signal for external ampliers (+12V)

* can also be used as a +12V power supply for active antenna splitters(max. 300 mA)

** must be activated in the Naviceiver in the app “DSP” under “EXT AMP”

DAdapter cable for factory USB port 2 (8-pin plug, brown)

Connect the adapter cable to the connector of the factory USB port.

Use this USB port in conjunction with the Media Connect function to connect your Android smartphone

to the Naviceiver.

C4G/LTE dongle (6-pin plug, turquoise)

Please note the information on page 11.

BUSB port 1 (4-pin plug, purple)

Use this USB port for USB storage media. For example, the cable can be routed into the glove compart-

ment so that the USB socket is accessible there.

DAB antenna plug from vehicle (brown connector)

WIRING DIAGRAM

FNot in use

HY adapter (6-pin plug, grex)

Red jack: Connection for the IR receiver of the optionally available

remote controller VNA-REM40

Black jack: Connection for the included external microphone

GAV cable set 2 for front or additional cameras (8-pin plug, blue)

RCA yellow (F-CAM IN): Video input for the front or additional cameras

Cable yellow (CAM +12V): Power supply for cameras

Cable black (CAM GND): Ground connection for cameras

NOTE: Refer to page 13 for more information on camera settings.

AAV cable set 1 (14-pin connector, black)

RCA white (FL): Audio output Front/Left

RCA red (FR): Audio output Front/Right

RCA white (RL): Audio output Rear/Left

RCA red (RR): Audio output Rear/Right

RCA green (SUB): Audio output Subwoofer

RCA yellow (VIDEO OUT 1): Video output for external monitor 1

RCA yellow (VIDEO OUT 2): Video output for external monitor 2

RCA yellow (VIDEO AUX IN): Video input for an external signal source

RCA yellow (R-CAM IN): Video input for analog rear view cam

Video input for analog HD rear view cam (AHD)*

If necessary, use the CAM +12V and CAM GND connections of the enclosed connection plug G (8-pin

plug, blue) to supply power to the camera.

* Only for compatible AHD cameras such as VNA-RCAM-DBJ228HD or VNA-RCAM-CS240HD.

NOTE: Refer to page 13 for more information on camera settings.

ENot in use

IMPORTANT NOTES

RECOMMENDED TOOLS

Cable ties

COMPATIBILIT Y

Renault Master III - 2nd facelift from year 2019/2020 with new dashboard

This device can only be installed in the following vehicles:

This guide is an aid for the professional installation of the device.

Please note the following notes before installation:

• Always handle all parts of the device and the components of your vehicle with care.

• Under all circumstances observe the regulations of the vehicle manufacturer and do not make any

changes to the vehicle which could impair driving safety.

• For safety reasons, disconnect the vehicle battery’s ground connection before installation.

• Please always pay attention to the correct polarity of the connections.

• Please do not modify any harnesses or connections of the device or the vehicle as this may affect

the warranty.

• Make sure that no cables are squashed or cause a short circuit.

• Do not lay cables in front of the airbags, e.g. in the dashboard or in a way that affects their function.

Torx T25 screwdriver or bit

PRE-ASSEMBLY

GENERAL INSTALLATION INSTRUCTIONS

GPS antenna

The GPS antenna should be glued horizontally to the dashboard with the

adhesive side down. Reception is not possible with a metal-coated pane.

Choose a level spot with a clear view of the sky. The location should be

about 50 - 70 cm away from the main unit, otherwise the GPS measurement

accuracy will decrease. When installing the GPS antenna in the vehicle, the

GPS accuracy is determined by the installation position and the body shape

of the vehicle. Accuracy is usually lower when the GPS antenna is installed

in the dashboard.

Remove the foil on

the bottom of the

GPS antenna

IMPORTANT NOTE: When using the device for the rst time and installing the navigation software for

the rst time, the search for GPS signals can take up to 30 minutes. After enough GPS satellites have

been found to determine the position, they are permanently stored in the device and can therefore be

found more quickly. If no GPS satellites are found afterwards or the GPS reception is poor, please note

the following:

In order for the navigation software to function properly, sufcient GPS reception must be ensured on

the Naviceiver. This is signicantly inuenced by the installation position of the GPS antenna in the

vehicle. Therefore, make sure that the GPS antenna is properly installed in your vehicle to ensure the

best possible reception.

Depending on the location or the topographical conditions in the reception area, GPS reception can vary

and thus affect the functionality of the navigation software. GPS reception is also dependent on local

satellite reception, which could be affected by current or global events.

Under certain circumstances, GPS reception can also be impaired by electronic devices such as smart-

phones, inductive charging cradle or toll devices (e.g. Telepass, GO-Box etc.) in the vicinity of the GPS

antenna. In this case, reposition the electronic devices.

Before beginning the installation, you must

pre-assemble the ESX Smart Naviceiver.

To do this, slide the device through the en-

closed mounting panel. The device must

then be screwed to the frame with the 4 en-

closed Phillips screws 2.5 x 9.5 mm. Only

use the screws provided, otherwise the

frame and/or the screen may be damaged.

INSTALLATION STEPS

The original mounting panel is clipped in at 9

points in the dashboard. Carefully pull the mount-

ing bezel off the dashboard by gently unclipping

each of the 4 corners.

Unscrew the 4 screws (T25) of the radio as

marked above.

If a radio is already installed in the radio slot, you

must rst remove it.

Now put the original mounting plate aside. This is

now no longer required.

Pull the radio out of the radio slot and remove all

connectors.

After the radio is uninstalled, the intermediate sta-

tus should look like shown above.

5 6

INSTALLATION STEPS

The central tray can be used for the GPS anten-

na. To do this, carefully remove the cover next to

the USB socket with a screwdriver to guide the

connection cable down into the radio slot.

After you have routed all connection cables out of

the radio slot, plug them into the corresponding

connections on the Naviceiver.

Use the openings at the back of the radio slot to

lead all relevant connection cables to the front.

The central tray or opening there can also be

used for the 4G/LTE antenna, GPS antenna and

the 4G/LTE dongle.

Also connect the brown USB plug and the vehi-

cle’s white system plug accordingly.

After all the connections on the Naviceiver are

connected, try to arrange the cables so that they

nd space in the radio slot.

11 12

INSTALLATION STEPS

Then slide the Naviceiver into the radio slot until it

has enough support. Do not clip in the Naviceiver

yet. Then carry out a functional test.

Use the openings at the back of the radio slot,

for example to store the CAN bus module of the

system plug.

After a successful function test, push the Navi-

ceiver further into the radio slot until it is complete-

ly clipped in.

Andere Handbücher für VISION ANDROID Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ESX Auto-Navigationssystem Handbücher

ESX

ESX VISION VNC1045-DBJ Bedienungsanleitung

ESX

ESX VNS830 SK-OC3 Bedienungsanleitung

ESX

ESX VN720 KI-SPORTAGE Bedienungsanleitung

ESX

ESX VN710 KI-SORENTO Bedienungsanleitung

ESX

ESX VISION NAVICEIVER VN610 MT-U1 Bedienungsanleitung

ESX

ESX VN830 Bedienungsanleitung

ESX

ESX Vision Naviceiver VN735 VO-P6C Bedienungsanleitung

ESX

ESX i40 Kurzanleitung

ESX

ESX VN710 CV-AVEO Bedienungsanleitung

ESX

ESX VNS730 FI-DUCATO Bedienungsanleitung

ESX

ESX VISION VNC1045-DBJ Bedienungsanleitung

ESX

ESX Vision Series Bedienungsanleitung

ESX

ESX VNS720 VW-U1 Bedienungsanleitung

ESX

ESX VN830 SK-OC3 Bedienungsanleitung

ESX

ESX VISION ANDROID Series Bedienungsanleitung

ESX

ESX VN720 VO-P6C Bedienungsanleitung

ESX

ESX VN710 KI-CEED Bedienungsanleitung

Beliebte Auto-Navigationssystem Handbücher anderer Marken

Clarion

Clarion Navigation In-Car Entertainment Bedienungsanleitung

Rosen

Rosen DP-1001 Bedienungsanleitung

Alpine

Alpine INE-W970HD Bedienungsanleitung

Skoda

Skoda AMUNDSEN+ Bedienungsanleitung

Blaupunkt

Blaupunkt TravelPilot DX-N Bedienungsanleitung

Pioneer

Pioneer MZ360500EX Bedienungsanleitung

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Bedienungsanleitung

Kenwood

Kenwood DNN991HD Bedienungsanleitung

AvMap

AvMap Geosat 2C Bedienungsanleitung

Eonon

Eonon GE01B Bedienungsanleitung

Pioneer

Pioneer AVIC-Z920DAB Bedienungsanleitung

Nextar

Nextar M3-MX - Automotive GPS Receiver Bedienungsanleitung

Furrion

Furrion NV2200 Bedienungsanleitung

Mio

Mio MOOV 200-Series Bedienungsanleitung

Prestigio

Prestigio GeoVision 5150 Bedienungsanleitung

Hummer

Hummer 2006 H3 Bedienungsanleitung

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Konfigurationshandbuch

Garmin

Garmin StreetPilot c510 Bedienungsanleitung