ESYLUX MD 180i/16 BASIC CH Bedienungsanleitung
1
ESYLUX GmbH | An der Strusbek 40
22926 Ahrensburg | Germany
Operating instructions
MD 180i/16 BASIC
EB10430459
MD 180i/16 BASIC CH
EB10430602
MA00564901
06/2017
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
2 / 19
GB
Table of contents
1 Description 3
2 Safety instructions 3
3 Operation / functionality 4
3.1 Conditions in which the lighting is switched on 4
3.2 Conditions in which the lighting is switched off 4
3.3 Switching delay – not in pulse mode 5
4 Installation / connection 5
4.1 Masking the field of detection 6
5 Activation 7
5.1 Overview of factory settings 7
6 Settings 7
6.1 Control via external “S” button 7
6.2 Configuring parameters via remote control 8
6.3 Mobil-PDi/MDi 8
6.4 Mobil-PDi/MDi temporary settings 9
6.5 Programming the Mobil-PDi/MDi 10
6.6 Mobil-PDi/MDi-universal 12
6.7 Mobil-PDi/MDi-universal temporary settings 12
6.8 Programming the Mobil-PDi/MDi-universal 13
6.9 “12 h ON / OFF” function 16
7 Technical data 17
8 Troubleshooting 18
8.1 Maintenance 18
8.2 Cleaning 19
9 ESYLUX manufacturer's guarantee 19
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
3 / 19
GB
1 Description
The ESYLUX wall-mounted motion detector is a passive infrared presence detector
which responds to moving heat sources, such as people walking.
The motion detector is designed for areas with low levels of natural light, such as
hallways, cellars, staircases, changing rooms, toilets, garages etc.
Parameters can be configured using the ESYLUX Mobil-PDi/MDi and Mobil-PDi/MDi-
universal remote controls.
Note: Use this product only as intended (as described in the user instructions).
The device must not be changed, modified or painted – doing so will void any warranty
claims. You must check the device for damage immediately after unpacking it. If there
is any damage, you should not install the device under any circumstances.
If you suspect that safe operation of the device cannot be guaranteed, you should turn
the device off immediately and make sure that it cannot be operated unintentionally.
2 Safety instructions
• Work on the 230-V power system must be carried out by authorised personnel only,
with due regard to the applicable installation regulations / standards
• Switch off the power supply before installing the system
• On the input side, the device is to be protected against short circuits with a 10-A circuit
breaker
• Protection type IP 40 for interior use
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
4 / 19
GB
3 Operation / functionality
• The ESYLUX wall-mounted motion detector, which has a 180° field of detection,
is only suitable for wall mounting
• The range is up to 16 m in diameter at a recommended installation height
of 1.10 - 2.20 m
• The motion detector has one channel (C1), which is used for presence-dependent
lighting control
• The setting options can vary depending on the remote control used; please see
“Configuring parameters via remote control”
3.1 Conditions in which the lighting is switched on
The lighting is switched on if the target brightness value is below the preset lux
value and movement is detected in the field of detection. Further movement is
acknowledged by the sensor with two short flashes of the red LED (the LED can be
switched off; see “Configuring parameters via remote control”). Once the lighting has
been switched on, the sensor deactivates light measurement for this period.
3.2 Conditions in which the lighting is switched off
The lighting is switched off if no movement is detected in the field of detection and
the preset switch-off delay time has elapsed.
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
5 / 19
GB
3.3 Switching delay – not in pulse mode
When persons are present, in order to avoid sudden changes in brightness caused by
undesired switching on / off of the lighting, the detector will only be triggered after a
time delay.
Example: a passing cloud could potentially cause unnecessary switching.
Time delay from light to dark: 30 sec. = red LED lights up during this period.
Time delay from dark to light: 5 min. = red LED flashes slowly during this period
4 Installation / connection
Note: Switch off the power supply before installing the system.
• The detector is designed to be installed in European flush-mounted boxes
• Specifications regarding the range of the detector relate to an ambient temperature
of approx. 20 °C
• Movement crossways to the detector is optimal for triggering the detector; head-on
approaches to the detector are more difficult to detect and therefore the range of
the detector is significantly reduced
16 m
12 m
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
6 / 19
GB
• The detector should be positioned depending on the available space and usage
requirements
• Make sure that the detector has a clear line of sight, as infrared beams cannot
penetrate solid objects
• Connect the detector in accordance with the circuit diagram
Single connection
Parallel connection
LPhase, 230 V
Lighting
Neutral conductor
Push button
4.1 Masking the field of detection
Part of the field of detection can be specifically masked off using the lens mask to
avoid false alarms being caused by e.g. pets.
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
7 / 19
GB
5 Activation
Connect the power supply.
A warm-up phase of 25 seconds is initiated. The red LED (for C1) and the blue LED
flash alternately: 2 x red and 1 x blue. During this time, the lighting is switched on.
5.1 Overview of factory settings
Factory settings
Light value approx. 100lux
Switch-off delay time 5 min.
Sensitivity 100 %
6 Settings
6.1 Control via external “S” button
The wall-mounted motion detector is equipped with a connection for an external
button (S terminal). This can be used to switch the lighting on and off manually.
Modes activated by pressing the external button:
Press button for approx. 1 second: The lighting is switched on or off.
Acknowledgement: green LED
Press button for approx. 3 second: The lighting is switched on or off continuously for
4 hours
Acknowledgement: red LED
Press button for approx. 5 second: The lighting is switched on or off continuously for
12 hours
Acknowledgement: blue LED
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
8 / 19
GB
The LED feedback can be used to determine the mode that the wall-mounted motion
detector is currently switched to.
Example: Please release the button after approx. 3 seconds – the red LED lights up and
the “4 h ON / OFF” mode is activated.
Further parameters can be configured via remote control. Remote controls can be
purchased as accessories.
6.2 Configuring parameters via remote control
Note: For optimum reception, when programming the settings, point the remote
control at the detector. Please note that if the sensor is exposed to direct sunlight, the
standard detection range of approx. 8 m may be dramatically reduced due to the sun's
infrared rays.
6.3 Mobil-PDi/MDi (EM10425509)
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
9 / 19
GB
6.4 Mobil-PDi/MDi temporary settings
Parameter configurations are only temporarily applied.
Function Customised setting
ON / OFF
Switching the lighting ON / OFF manually.
Note: The “ON / OFF” mode can be cancelled by pressing the “Reset” button.
“ON” acknowledgement: Movement detected in the field of detection is
acknowledged with two short flashes of the red LED.
“OFF” acknowledgement: Movement detected in the field of detection is
acknowledged with one short flash of the red LED.
Reset / settings
Temporarily set values are cleared and the detector returns to the manually
preset operating mode.
Test
Test mode is used for testing the field of detection and takes approx. 5 min.
During this time, the lighting is switched on. Afterwards, the detector returns
to the preset operating mode.
Acknowledgement: Movement detected in the field of detection is
acknowledged with two short flashes of the blue LED.
4 h ON / OFF
The lighting is switched on or off continuously for approx. 4 hours. If no
movement is detected in the field of detection and the preset switch-off delay
time has elapsed, the detector returns to the previous operating mode.
Note: The “4 h ON / OFF” mode can be cancelled by pressing the “Reset”
button.
OPERATING INSTRUCTIONS
MD 180i/16 BASIC
MD 180i/16 BASIC CH
10 / 19
GB
6.5 Programming the Mobil-PDi/MDi
Alterations to parameters are applied permanently.
Function Customised setting
Enter programming mode
The detector goes into programming mode.
Acknowledgement: The blue LED lights up permanently and the lighting is
switched on continuously.
Exit programming mode
The set parameters are stored on the detector.
Acknowledgement: The blue LED is switched off.
Set the brightness switching value, max. 1000 lux
The detector switches the lighting on if the target brightness value is below the
preset lux value and movement is detected in the field of detection.
Acknowledgement: The red and blue LEDs flash three times.
Take a reading of the current ambient light value
The detector switches the lighting on if the target brightness value is below the
preset lux value and movement is detected.
Acknowledgement: The blue LED and the lighting are switched off for approx.
5 seconds while the reading is taken.
Fully automatic / semi-automatic mode
The lighting can be controlled in fully automatic and semi-automatic modes.
Fully automatic: The lighting is switched on depending on the set lux value
and movement being detected. If movement is no longer detected, the preset
switch-off delay time will start. The relevant active status can be optionally
overridden using the external “S” button.
Acknowledgement: The blue LED flashes three times.
Semi-automatic: Control (activation of the lighting) via the external “S”
button. The lighting remains switched on as long as movement is detected and
the target brightness value is greater than the preset lux value.
Acknowledgement: The blue LED is switched off for approx. 2 seconds.
Short pulse
As soon as movement has been detected in the field of detection, the detector
switches the lighting on for approx. 1 second and off for approx. 9 seconds.
This function can be used to control automatic stairwell lights, for example.
Acknowledgement: The red LED is switched on for approx. 5 seconds and off
for 5 seconds.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere ESYLUX Sicherheitssensor Handbücher
ESYLUX
ESYLUX MD-W200i Bedienungsanleitung
ESYLUX
ESYLUX PD-C360i/24 DUODIMplus-FM Bedienungsanleitung
ESYLUX
ESYLUX PD 360/8 Basic Bedienungs- und Wartungshandbuch
ESYLUX
ESYLUX RC 130i Bedienungsanleitung
ESYLUX
ESYLUX MD 120 Bedienungsanleitung
ESYLUX
ESYLUX SMB MD 360i/24 Basic SMB Bedienungs- und Wartungshandbuch
ESYLUX
ESYLUX PD 360/8 KNX BASIC Bedienungsanleitung
ESYLUX
ESYLUX PD-C360i/24 DUODIMplus-FM Bedienungsanleitung
ESYLUX
ESYLUX MD 120 Bedienungsanleitung
ESYLUX
ESYLUX RC 230i KNX Bedienungsanleitung
ESYLUX
ESYLUX EM10041006 Bedienungsanleitung
ESYLUX
ESYLUX MD-C 180i/16 Touch Bedienungs- und Wartungshandbuch
ESYLUX
ESYLUX PD-C360i/24 KNX ECO Bedienungsanleitung
ESYLUX
ESYLUX PD-C360i/24 DUOplus-FM Bedienungsanleitung
ESYLUX
ESYLUX MD-C360i/8 Series Bedienungsanleitung
ESYLUX
ESYLUX COMPACT APC10 DALI-2 Bedienungsanleitung
ESYLUX
ESYLUX PD-C360i/24 DIMplus Bedienungsanleitung
ESYLUX
ESYLUX PROTECTOR WD 9 V Bedienungsanleitung
ESYLUX
ESYLUX PD 360i/8 DALI ADR Bedienungsanleitung
ESYLUX
ESYLUX RC 130i Bedienungsanleitung
