ETC F-Drive Series Bedienungsanleitung

ETC Reference Guide

F-Drive R12 and W1 Wiring

Corporate Headquarters nMiddleton, WI, USA |+1 608 831 4116

New York, NY |Orlando, FL |Los Angeles, CA |Austin, TX

Web etcconnect.com |Support support.etcconnect.com |Contact etcconnect.com/contactETC

Product information and specifications subject to change. ETCintends this document to be provided in its entirety.

7148M2400 Rev D Released 2022-01

Introduction

This guide covers wiring considerations for the F-Drive series of drivers, including F-Drive R12 and

F-Drive W1Drivers and wiring schemes with and without the B-Box4. F-Drive series drivers offer

centralized control of ArcSystem Navis luminaires, ArcSystem Pro One-Cell luminaires, and third-party

fixtures. Output wiring requirements and methods vary depending on the load and the chosen wire

type. For more information on compatible products, see the resources below.

F-Drive System Design Tool

The F-Drive System Design Tool (etcconnect.com/Products/Power-Controls/LED-Drivers/F-Drive/F-

Drive-System-Design-Tool.aspx) allows you to design an F-Drive R12 rack unit or F-Drive W1 driver

with different luminaires, breakout boxes, cable lengths, and other system components.

LEDDimming Compatibility Database

The LEDDimming Compatibility Database (etcconnect.com/compatibility/) is a searchable list of

devices that ETChas tested for compatibility with ETCdimming and control systems.

Documentation for Compatible Products

The following documents are available at etcconnect.com/Products/Power-Controls/LED-Drivers/F-

Drive/Documentation.aspx:

•

F-Drive B-Box4 Installation Guide

•

F-Drive Series R12 Installation Manual

•

F-Drive Series W1 Installation Manual

The following document is available at etcconnect.com/Products/Lighting-Fixtures/ArcSystem-

Navis/Documentation.aspx:

•

ArcSystem Navis 100 Installation Guide

The following document is available at etcconnect.com/Products/Lighting-Fixtures/Pro-One-

Cell/Documentation.aspx:

•

ArcSystem Pro D1 and D2 Series Drivers Installation Guide

The following document is available at etcconnect.com/Products/Lighting-

Fixtures/ArcLamp/Documentation.aspx

•

ArcLamp System Installation Manual

For current technical information about the MEANWELLRKP-1UI three-bay frame and RCP-2000

48VDC power supplies, visit https://www.meanwell.com. The

RCP-2000/RKP-1UI Instruction Manual

is available at https://www.meanwell.com/webapp/product/search.aspx?prod=RCP-

2000&pdf=UkNQLTIwMDAsUktQLTFVLUUucGRm&a=4.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 2 of 17 ETC

Load Types &Configurations

F-Drive R12 has modular output cards that can drive a variety of loads, and F-Drive W1Drivers come

in different models to drive a variety of loads. This document covers the following load types and

configurations:

•

ArcSystem Navis on page 2

ArcSystem Navis in Daisy Chain on page5

ArcSystem Navis in Star Topology with an FD-BBOX-4R on page7

•

ArcSystem Pro One-Cell Luminaires on page8

ArcSystem Pro One-Cell Luminaires with an FD-BBOX-4M on page9

ArcSystem Pro One-Cell Luminaires without an FD-BBOX-4M on page10

•

Third-Party Loads on page11

Third-Party Constant Current Loads with an FD-BBOX-4T on page12

Third-Party Loads without an FD-BBOX-4T on page13

RGBW LED Tape on page15

•

ArcSystem ArcLamp on page17

CAUTION:

Do not coil excess Category-type cable.

Note:

Cable bundling limitations apply to F-Drive R12 Class 2 output cables. For more

information about maximum number of four-pair cables in a bundle, see NFPA 70 2020

National Electrical Code, table 725.144.

Note:

Certain output card and load configurations may overload the F-Drive R12 System.

Visit the F-Drive System Design Tool (etcconnect.com/Products/Power-Controls/LED-

Drivers/F-Drive/F-Drive-System-Design-Tool.aspx) for more information about system limits.

ArcSystem Navis

CAUTION:

Possible damage to equipment. Connect only Navis100 Fixed White

luminaires to a W1CCDriver. Connectonly Navis100 Fade to Warm luminaires to

a W1FadetoWarmDriver. Connect only Navis100 RGBW luminaires to a W1

Chroma Driver.

CAUTION:

Possible damage to equipment. Connect only the same types of

luminaires in a wiring run. DONOT mix Fixed White, Fade to Warm, and RGBW

luminaires in the same wiring run.

Note:

The W1 Chroma Driver and R12 ChromaCard ship with an RJ45 DMXterminator.

Navis RGBWluminaires are not self-terminating. You must terminate the last Navis

RGBWluminaire in line with a 120

resistor.

To purchase extra RJ45 terminators, please contact your ETCcustomer service

representative and request part number N4086.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 3 of 17 ETC

Category-Type Cable Requirements

ArcSystem Navis Luminaires typically connect to the F-Drive W1Driver or F-Drive R12 output card

via Category-type cable terminated to RJ45 connectors. If you are installing a B-Box4 between the

driver and the luminaire, install Category-type cable between the driver and B-Box4 and between

the B-Box4 and the luminaire. ArcSystem Navis luminaires require:

•

0.25mm2(23AWG) or larger conductors in Category-type cable

•

100 m (328 ft) maximum wire run length (including twice the stem length of the pendant

accessory if you are installing a pendant)

•

2.4 A maximum per cable

CAUTION:

Do not coil excess Category-type cable.

Cable Bundling

Note:

Cable bundling limitations apply to F-Drive R12 Class 2 output cables. For more

information about maximum number of four-pair cables in a bundle, see NFPA 70 2020

National Electrical Code, table 725.144.

The conductors in the category-type cable have a maximum current that they can carry before

exceeding the temperature rating of the cable. This limit restricts the number of cables that can be

bundled together.

Navis Luminaire Current Requirements

•

1–4 daisy-chained Navis100 RGBW luminaires require 1 Aacross 3 wire pairs

•

1–4 daisy-chained Navis100 Fixed White luminaires require 0.7 A per wire pair

•

1–4 daisy-chained Navis100 Fade to Warm luminaires require 0.45 A per wire pair

Limits for 75°CRated Cable

The current requirements of each Navis luminaire type limit the number of four-pair cables per

bundle. The limits below are for cable with 0.25mm2(23AWG) conductors rated to 75°C:

•

19 four-pair cables per bundle if any cables go to Navis100 RGBWluminaires

•

91 four-pair cables per bundle if all cables go to Navis100 Fixed White luminaires or a

combination of Navis100 Fixed White and Navis100 Fade to Warm luminaires

•

192 four-pair cables per bundle if all cables go toNavis100 Fade to Warm luminaires

Patching Requirements

If you are using a patch panel between the F-Drive W1Driver or F-Drive R12 output card and Navis

luminaires, pins must be rated for more than 1A.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 4 of 17 ETC

Constant Current Driver Configuration for ArcSystem Navis

Luminaires

CAUTION:

Setting the F-Drive CC-150Card or W1CVDriver to output more

current than the manufacturer recommends for the loads may reduce the lifetime

or cause damage to the load.

The CC-150Card and the W1CCDriver are set by default to provide the appropriate current for

ArcSystem Navis100 Fixed White luminaires (600 mA), but the output can be adjusted between 200–700mA

for compatibility with ArcSystem Pro One-Cell luminaires and third-party loads. Output current can

be configured via RDM. See

ArcSystem Pro One-Cell Luminaires on page8

and the

F-Drive R12

Series Installation Manual

or the

F-Drive W1 Series Installation Manual

for more details.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 5 of 17 ETC

ArcSystem Navis in Daisy Chain

ArcSystem Navis100 Fixed White,Fade to Warm,andRGBWluminaires can be daisy-chained

together using their RJ45 In and Out ports. See the

Arcsystem Navis 100 Installation Guide

for

details.

F-Drive R12 with Daisy Chain of ArcSystem Navis

D C B

Description Notes

A F-Drive R12

B CC-150Card The CC-150Card outputs constant current, adjustable from 200–700mA. The factory-set output current

is 600mA, which is compatible with Navis100 Fixed White luminaires.*

C FTW-150Card The FTW-150Card outputs 450 mA constant current, compatible with Navis100 Fade to Warm

luminaires.

D ChromaCard The ChromaCard is only compatible with Navis100 RGBWluminaires.

ECategory-type

cable

You must use 0.25mm2(23AWG) or larger conductors in Category-type cable. Not all Cat5 or Cat6

cables meet this requirement.

FN4086 120Ω

terminator

Navis 100 RGBW luminaires are not self-terminating. You must terminate the last luminaire in line with a

120 Ωresistor.

An RJ45 terminator is included with each F-Drive R12 Chroma Card. To purchase extra RJ45 terminators,

please contact your ETC customer service representative and request part number N4086.

GNavis100 RGBW

luminaires Daisy chain of fourARCN100 RGBW luminaires per ChromaCard

HNavis100 Fade to

Warmluminaires Daisy chain of four ARCN100Fade to Warmluminaires per FTW-150Card

INavis100 Fixed

White luminaires Daisy chain of four ARCN100Fixed White luminaires per CC-150Card

*See

Constant Current Driver Configuration for ArcSystem Navis Luminaires on the previous page

Note:The illustration is not drawn to scale.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 6 of 17 ETC

F-Drive W1 with Daisy Chain of ArcSystem Navis

1 2 3 4

DMX

THRU

MAINTAIN

1 2 3 4

DMX

THRU

MAINTAIN

DMX

THRU

MAINTAIN

Description Notes

AW1CCDriver or

W1CCEmergencyDriver

The W1CCDriver outputs constant current, adjustable from 200–700mA. The

factory-set output current is 600mA, which is compatible with Navis100 Fixed White

luminaires.*

W1CCDriver shown.

BW1FadetoWarmDriver or

W1FadetoWarmEmergencyDriver

The W1FadetoWarmDriver outputs 450 mA constant current, compatible with

Navis100 Fade to Warm luminaires.

W1FadetoWarmDriver shown.

C W1 Chroma Driver The W1 Chroma Driver outputs power and data that is compatible with

Navis100 RGBW luminaires.

D Category-type cable You must use 0.25mm2(23AWG) or larger conductors in Category-type cable. Not

all Cat5 or Cat6 cables meet this requirement.

E Navis100 Fixed White luminaires Daisy chain of four ARCN100 Fixed White luminaires

F Navis100 Fade to Warmluminaires Daisy chain of four ARCN100 Fade to Warmluminaires

G Navis100 RGBWluminaires Daisy chain of four ARCN100 RGBWluminaires

H 120Ωterminator

Navis 100 RGBW luminaires are not self-terminating. You must terminate the last

luminaire in line with a 120 Ωresistor.

An RJ45 terminator is included with each W1 Chroma Driver. To purchase extra RJ45

terminators, please contact your ETC customer service representative and request

part number N4086.

*See

Constant Current Driver Configuration for ArcSystem Navis Luminaires on page4

Note:The illustration is not drawn to scale.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 7 of 17 ETC

ArcSystem Navis in Star Topology with an FD-BBOX-4R

Drive up to four Navis Fixed White or Fade to Warm luminaires in star topology per F-Drive W1 or

per R12 output card with a FD-BBOX-4R. FD-BBOX-4R takes a single four-channel RJ45 output from

F-Drive R12 CC-150Card, FTW-150Card, W1CCDriver, or W1FadetoWarmDriver and provides

four separated RJ45 outputs for ArcSystem Navis luminaires. Refer to the

F-Drive B-Box4 Installation

Guide

and visit the F-Drive System Design Tool at etcconnect.com/Products/Power-Controls/LED-

Drivers/F-Drive/F-Drive-System-Design-Tool.aspx to learn more.

Note:

Navis RGBW luminaires are not compatible with B-Box4.

Note:

If used within an Emergency Lighting Circuit, follow NECmarking requirements or

local jurisdiction requirements.

Ch 4

Ch 3

Ch 2

Ch 1

SENSE

1 2 3 4

DMX

THRU

MAINTAIN

FDR12FD

FD-BBOX-4R

FDW1CCD (-CE)/FDW1FTWD (-CE)

Driver can be W1

or R12

Description Notes

CC-150Card or FTW-150Card

installed in one card slot of an

FDR12FD

The CC-150Card and W1CCDriver output constant current, adjustable from 200–

700mA. The factory-set output current is 600mA, which is compatible with Navis100

Fixed White luminaires.*

The FTW-150Card and W1FadetoWarmDriver output 450 mA constant current,

compatible with Navis100 Fade to Warm luminaires.

W1CCDriver or

W1FadetoWarmDriver

B Category-type cable* You must use 0.25mm2(23AWG) or larger conductors in Category-type cable. Not all Cat5

or Cat6 cables meet this requirement.

C ArcSystem Navis100 luminaire ARCN100 Fixed White or Fade to Warm.

*See

Constant Current Driver Configuration for ArcSystem Navis Luminaires on page4

Note:The illustration is not drawn to scale.

Note:

Navis luminaires will not function if they are

daisy-chained off of each other from the output of the

B-Box.

FD-BBOX-4R

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 8 of 17 ETC

ArcSystem Pro One-Cell Luminaires

Note:

Maximum supported wire length between ArcSystem Pro One-Cell Standard,

Small, and Micro luminaires and F-Drive R12 or W1 is 100 m (328 ft).

Constant Current Driver Configuration for ArcSystem Pro One-Cell

Luminaires

The R12 CC-150Card and the W1CCDriver can output 200–700 mA for compatibility with

ArcSystem Pro One-Cell White and Fade to Warm (FTW)luminaires and third-party loads. Output

current can be configured via RDM. See the

F-Drive R12 Series Installation Manual

or the

F-Drive W1

Series Installation Manual

for more details. ArcSystem luminaire current requirements are below.

CAUTION:

Setting the F-Drive CC-150Card or W1CVDriver to output more

current than the manufacturer recommends for the loads may reduce the lifetime

or cause damage to the load.

Note:

ArcSystem Pro One-Cell Micro luminaires require 200 mA and should only be run

by a CC-150Card or W1CCDriver output channel configured to 200 mA.

ETCLuminaire Current Requirement

ArcSystem Navis100 Fixed White 600 mA

ArcSystem Pro One-Cell White or Fade to Warm 600 mA

ArcSystem Pro One-Cell Small White or Fade to Warm 600 mA

ArcSystem Pro One-Cell Micro White or Fade to Warm 200 mA

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 9 of 17 ETC

ArcSystem Pro One-Cell Luminaires with an FD-BBOX-4M

The most convenient way to connect ArcSystem Pro One-Cell luminaires to an

F-Drive R12 CC-150Cardor W1CCDriver is with an F-Drive FD-BBOX-4M. FD-BBOX-4M takes a

single four-channel RJ45 output from an F-Drive R12 CC-150Card or W1CCDriver and provides four

separated Molex outputs for ArcSystem Pro One-Cell luminaires. Refer to the

F-Drive B-Box4

Installation Guide

and visit the F-Drive System Design Tool at etcconnect.com/Products/Power-

Controls/LED-Drivers/F-Drive/F-Drive-System-Design-Tool.aspx.

Note:

If used within an Emergency Lighting Circuit, follow NECmarking requirements or

local jurisdiction requirements.

SENSE

1 2 3 4

DMX

THRU

MAINTAIN

FDR12FD

FD-BBOX-4M

Ch 4

Ch 3

Ch 2

Ch 1

DDD

FDW1CCD (-CE)

Driver can be W1

or R12

Description Notes

CC-150Card installed in

one card slot of an

FDR12FD The CC-150Card and W1CCDriver output constant current, adjustable from 200–700mA.*

W1CCDriver

B Category-type cable

The cable from the RJ45 output of the driver to the input of the FD-BBOX-4M. You must use

0.25mm2(23AWG) or larger conductors in Category-type cable. Not all Cat5 or Cat6 cables meet

this requirement.

CUse cable attached to

ArcSystem Pro luminaire

Extension cables are available. See the datasheet for ArcSystem Pro One-Cell luminaires at

etcconnect.com/arcsystem.

DArcSystem Pro One-Cell

luminaire

Pro One-Cell (ARCP1), Pro One-Cell Small (ARCP1S), or Pro One-Cell Micro* (ARCP1M); White or

Fade to Warm.

*See

Constant Current Driver Configuration for ArcSystem Pro One-Cell Luminaires on the previous page

Note:The illustration is not drawn to scale.

ETC Reference Guide

F-Drive R12 and W1 Wiring

F-Drive R12 and W1 Wiring Page 10 of 17 ETC

ArcSystem Pro One-Cell Luminaires without an FD-BBOX-4M

ArcSystem Pro One-Cell Fixed White and Fade to Warmluminaires can be wired to the F-Drive

W1CCDriver or R12 CC-150Card using the two-pin outputs on the driver or output card. Each

luminaire requires its own cable and two-pin output from the output card. See the

F-Drive R12 Series

Installation Manual

or the

F-Drive W1 Series Installation Manual

for pinout details.

1 2 3 4

DMX

THRU

MAINTAIN

Description Notes

A F-Drive R12

B CC-150Card

The CC-150Card outputs constant current, adjustable from 200–700mA. The factory-set output current is

600mA, which is compatible with ArcSystem Pro One-Cell ArcSystem Pro One-Cell Small luminaires. You must

adjust the current if you are installing ArcSystem Pro One-Cell Micro luminaires.*

CLuminaire

cable Use the cable attached to the luminaire.

D Four ArcSystemPro One-Cell luminaires

E W1CCDriver

*See

Constant Current Driver Configuration for ArcSystem Pro One-Cell Luminaires on page 8

Note:The illustration is not drawn to scale.

Note:

ArcSystem Pro One-Cell luminaires have different wire color conventions on their

input cables. See the table below for wire colors and see the

F-Drive Series R12 Installation

Manual

F-Drive Series W1 Installation Manual

for the pinouts of the terminals on the R12

or W1.

Luminaire Wire Color and Polarity

Red Black

ArcSystem Pro One-Cell (standard) negative (-) positive (+)

ArcSystem Pro One-Cell Small negative (-) positive (+)

ArcSystem Pro One-Cell Micro positive (+) negative (-)

Andere Handbücher für F-Drive Series

Dieses Handbuch passt für folgende Modelle

Andere ETC Computerhardware Handbücher

ETC

ETC F-Drive R12 Series Bedienungsanleitung

ETC

ETC 7123K1028-REPLC Bedienungsanleitung

ETC

ETC Power Control Processor Merkblatt

ETC

ETC E-ACP Kurzanleitung

ETC

ETC Response Mk2 One-Port Kurzanleitung

ETC

ETC Ion Xe RPE Bedienungsanleitung

ETC

ETC Power Control Processor Merkblatt

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung