ETI NETCOM ADH Bedienungsanleitung
South Bend, Indiana USA | networketi.com ADH INSTALLATION GUIDE | PART NO. 23617 REV B
MODEL ADH
NETCOM
®
AUTOMATIC DEHYDRATOR WITH AC POWER SUPPLY
PACKING LIST
QTY. PART NO. DESCRIPTION
123437 ADH NETCOM Automatic Dehydrator, AC Power Supply
124303 Documentation CD ROM, ADH NETCOM and ASM–1 Smart Manifold
123229 ADH NETCOM Installation Sheet
118198 1/8” NPT to 1/4” Barbed Brass Fitting
123428 1/8” NPT to 3/8” Barbed Brass Fitting
114513 1/8” NPT to 1/4” Barbed Elbow Brass Fitting
423245 Mounting Bracket
824567 Self-Locking Rack-Mounting Screw (#8-32)
810641 #8 Split Washer
CONNECTIONS
1. Connect feed hose to 1/8” NPT outlet using 1/4” or
3/8” barbed tting supplied.
2. Connect required data and alarm relay ports. RS-422
and RS-232 ports may require conguration changes
via the web interface. See Instruction Manual for
more information.
3. Connect AC power cord. System can be connected
to 100 VAC – 240 VAC power without requiring any
conguration change.
South Bend, Indiana USA | networketi.com ADH INSTALLATION GUIDE | PART NO. 23617 REV B
2
RACK MOUNTING
The dehydrator is equipped with
positions for either ush-mounting
(for dual-post racks and enclosures) or
center-mounting (for singlepost racks).
If using mounting rails (not supplied),
do not install mounting brackets.
WALL MOUNTING
Ensure the mounting surface and
hardware are suitable to support
a static load of approximately four
times the weight of the unit, or 64
pounds (29 kg). Use four appropriate
5/16” mounting hardware to fasten
the unit and ensure stable mounting.
The dehydrator is equipped with four
brackets for wall mounting.
WALL MOUNTING CONFIGURATION
To congure the dehydrator for wall
mount installation, remove the front
panel and the portion of the vented
cover with the ETI logo.
Reinstall the front panel so that it will
be in the new front position once
the dehydrator is positioned for wall
mounting. Reinstall the small vented
panel so that it will be in the new
bottom position.
South Bend, Indiana USA | networketi.com ADH INSTALLATION GUIDE | PART NO. 23617 REV B
3
COMMUNICATING WITH THE DEHYDRATOR
Note: Your Information Technology Department is the
best source of information if you encounter problems or
difculties in connecting to or communicating with the
dehydrator. The ADH NETCOM Ethernet communica-
tions run at 10Base-T and half duplex. It is recommended
tht the network interface to the ADH NETCOM is mau-
nally set to these parameters and NOT to an auto-con-
gure mode.
1. Temporarily assign computer an IP address in the
192.168.52.0 network range, typically 192.168.52.1,
with the subnet 255.255.255.0
2. Connect the dehydrator to your computer either
directly or through a network. For direct connections
a cross-over cable or switch may be required for
connecting to an older computer; an Ethernet patch
cable will work in most other cases.
3. Open a web browser and connect to web interface at
HTTP: //192.168.52.9
CONFIGURING IP ADDRESS
1. Go to Conguration page
2. If using a xed IP address, select “Use the following IP
address:” Then set the IP address, mask and gateway.
3. If using DHCP, select “Obtain IP address automatically.”
4. Click Submit. You should see a message that the
dehydrator is rebooting.
CONFIGURING PRESSURE
1. Using a web browser, connect to the dehydrator. Go
to the Conguration page
2. Using the Units pull-down select English (PSI) or
SI (mbar).
3. To change the operational pressure setting enter the
following:
• Low Alarm - The pressure at which Low Pressure will
cause an alarm condition.
• Low Limit - The low set point at which the unit will
start pumping.
• High Limit - The high set point at which the unit will
stop pumping.
• High Alarm - The pressure at which High Pressure
will cause an alarm condition.
4. Click submit.
After changing the IP address of your dehy-
drator to a network other than the default
192.168.52.0 you will not be able to access
the dehydrator from the conguring com-
puter unless that computer is recongured
for the newly assigned network address.
NOTE:
South Bend, Indiana USA | networketi.com ADH INSTALLATION GUIDE | PART NO. 23617 REV B
4
CONTACTING CUSTOMER SERVICE
For technical help, questions or comments concerning
this product or any ETI product contact Customer Service
8:00 a.m. - 5:00 p.m. EST.
Email: [email protected]
Web: networketi.com
Mail: ETI
1850 North Sheridan Street
South Bend, IN 46628
LIMITED WARRANTY
ETI’s two year limited warranty covering defects in
workmanship and materials applies. Contact Customer
Service for complete warranty information.
DISCLAIMER
ETI makes no representations or warranties, either
expressed or implied, with respect to the contents
of this publication or the products that it describes,
and specically disclaims any implied warranties of
merchantability or tness for any particular purpose. ETI
reserves the right to revise this publication, and to make
changes and improvements to the products described
in this publication, without the obligation of ETI to notify
any person or organization of such revisions, changes or
improvements.
Copyright © 2019 ETI,
®
All rights reserved.
Andere Handbücher für NETCOM ADH
8
Andere ETI Trockner Handbücher
Beliebte Trockner Handbücher anderer Marken
Indesit
Indesit IDV 75 Bedienungsanleitung
Infiniton
Infiniton SD-DG85C Bedienungsanleitung
BOMANN
BOMANN WT 5019 Bedienungsanleitung
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Bedienungsanleitung
Asko
Asko T793C Bedienungsanleitung
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung