ETI IR-500 Bedienungsanleitung

User Manual





Product Code





Use this instrument only as specified in this manual, otherwise, the protection

provided by the instrument may be impaired.

Please note the warnings and cautions listed below.

WARNINGS

 touch the IR target surface of the unit.

The temperature of the IR target surface is the same as the actual temperature

shown on the display. If the unit is set at 500 °C and the display reads 500 °C,

the target surface is 500 °C. The top of the instrument case may exhibit extreme

temperatures for areas close to the IR target surface.

 turn off the unit at temperatures higher than 50 °C. This could create

a hazardous situation.

 connect and operate this unit without a properly grounded, properly

polarized power cord.

 is used in the operation of this equipment. Severe injury or death

may result if personnel fail to observe safety precautions. Before working inside the

equipment, turn the power off and disconnect the power cord. Overhead clearance

is required.

 place this instrument under a cabinet or other structure.

 use this unit in conditions other than those listed in the environmental

conditions section (page 5).

 operate near flammable materials.

Use of this instrument at  for extended periods of time

requires caution. Completely unattended high temperature operation is not

recommended for safety reasons.

CAUTIONS

To avoid possible damage to the instrument, follow these guidelines.

 plug the unit into 220V if the heater switches and fuse holder read

11OV. This action will cause the fuses to blow and may damage the instrument.

 use fluids to clean the target surface.

 change the values of the calibration constants from the factory set values.

The correct setting of these parameters is important to the safety and proper

operation of the calibrator.



The IR-500 Calibrator is mainly structured by 58 mm diameter target assembly

and dry-well temperature system controlled by a microcomputer. The external

reference thermometer is a metal cone with good heat-conducting ability, on the

surface of thermometer there is a oxide lm with emissivity 0.95.

The IR-500 Calibrator contains a class-A PT100 sensor with a temperature control

system and wind-cold device. The calibrator has rapid heating and cooling

functions and is switchable between °C/°F, which can be used for different

temperature unit calibrations.

The calibrator operates over a range of 50 °C to 500 °C with a temperature display

resolution of 0.1 °C.

3.GENERAL SPECIFICATIONS

Range 50 °C to 500 °C (122 °F to 932 °F)

  0.1 °C

 ±1 °C below 100 °C

±2 °C from 100 °C to 200 °C

±3 °C from 200 to 500 °C)

 ±0.1°C at Temp<100 °C (±0.2 °F at Temp<212 °F)

±0.2 °C at 1OO °C<Temp<350 °C

(±0.4 °F at 212 °F<Temp<662 °F)

±0.4°C at 200°C<Temp<500 °C

(±O.8 °F at 392 °F<Temp<932 °F)

 40 minutes to max

 30 minutes to 100 °C (212 °F)

 0.95 xed

 Ø58 mm

 110 volt AC, 3A or 230 volt AC (±10%), 1.5A

 114 x 180 x 233 mm

Weight 2682 grams





Although the instrument has been designed for optimum durability and

trouble-free operation, it must be handled with care.

The instrument should not be operated in an excessively dusty or dirty

environment.

Maintenance and cleaning recommendations can be found in the

Maintenance section of this manual.

The instrument operates safely under the following conditions:



 5-35 °C (41-95 °F)

 15-80%

 75kPa - 106kPa

Mains voltage within ±10% of nominal.

Vibrations in the calibration environment should be minimized.





Unpack the calibrator carefully and inspect it for any damage that may

have occurred during shipment. If there is shipping damage notify ETI Ltd

immediately.

Verify that the following components are present:

• Calibrator

• Power Cord

• User Manual



Place the calibrator on a at surface with at least 8 inches of free space around

the instrument. The stand may be swung down to raise the front of the

instrument from a horizontal position. Plug the power cord into a grounded

mains outlet (Note: this calibrator has two power specications of one model

NO:220V/AC and 11OV/AC, please make sure the power value is suitable for the

instrument before operation.)

Turn on the power to the calibrator by toggling the power switch on. The fan

should begin quietly blowing air through the instrument and the controller

display should illuminate after 3 seconds. After a brief self-test the controller

should begin normal operation. If the unit fails to operate please check the

power connection.

The heater will start operating to bring the temperature of the calibrator to

the set-point temperature and the display will begin to show the actual target

temperature.

The unit should be used with a secondary certied reference thermometer

(E.g. ETI Reference Thermometer product code 222-055)



Press "UP" or "DOWN" to change the set-point value.

Then press "SET". The calibrator will automatically control the target assembly

temperature to reach the set temperature in the stated time. The red LED

display will indicate the temperature of the target assembly. When the set-point

temperature is changed the controller switches the well heater on or off to raise

or lower the temperature. The displayed well temperature gradually changes

until it reaches the set-point temperature. The well may require 5 to 10 minutes

to reach the set-point depending on the span. Another 5 to 10 minutes is

required to stabilise within ±0.1 °C of the set-point. Ultimate stability may take 15

to 20 minutes more of stabilisation time.



The user should become familiar with the calibrator and its parts.







The back panel () consists of the power cord inlet, power switch, heater

voltage switch, and fan.

1Wind input

2Fuse of heater

3Fuse of temperature control system

4Power Input

5Power switch

Power Inlet - At the rear of the calibrator is the removable power cord inlet that

plugs into an IEC grounded socket.

Do not plug the unit into 220V if the unit is indicated as 110V. This

action will cause the fuses to blow and may damage the instrument.

Fan - The fan inside the calibrator has two speeds and runs continuously when

the unit is being operated to provide cooling for the instrument.

The fan runs slow for heating and maintaining operation and runs fast for rapid

cooling. Slots are provided for airow. The area around the calibrator must be

kept clear to allow adequate ventilation. The airow is directed out the front and

can be extremely hot



The front panel() consists of the controller display, controller keypad.

and target assembly.



Controller Display

1 The red LED (the rst line display) displays actual temperatures and

settings for selected scale °C or °F.

2 The green LED (the second line) displays the set-point value and shows

temperatures in units according to selected scale °C or °F.

3 The indicator of the operation state

• AT - Automotive parameter adjustment.(only used to factory for adjusted)

• OUT - The indicator of heat output with indication of the heating state of the

target assembly

• ALM1 - 0verload alarm when the target assembly temperature 4 °C higher than

the set temperature,indicates the heating power off

• ALM2 - 0verload alarm. when the target assembly temperature 4 °C higher

than the set temperature,indicates the cooling with strong wind

• °F - °F temperature indicator

• 0°C - 0°C temperature indicator.



The four button keypad allows easy setting of the set-point temperature.

• SET - Used to conrm parameter settings.

• - The enter button .Used with the set button to enter conguration mode.

• DOWN - Used to decrease temperature value and change the unit °C to °F.

• UP - Used to increase temperature value and change the unit °C to °F.

5 Target assembly, The target assembly is 58 mm in diameter and has an

emissivity at 0.95.

6 The test hole for the temperature sensor of the Reference thermometer.



Place the calibrator on a at surface with at least 8 inches of free space around

the instrument, with the instrument facing the user.

•Connect the calibrator to the power supply, ensuring correct voltage

(11OV or 220V).

•Press the "on" button to power the unit on.



The calibrator can display temperature in Celsius or Fahrenheit.

The temperature units are shipped from the factory set to Celsius and locked.



Press the "SET" and " " buttons at the same time.

After unlocking, rst press the "SET" button for three seconds, the red LED on the

rst line will display

the second line green LED will display "pt2";

Release the "SET" button and press the " " button, the green LED on the

second line will indicate the current temperature unit.

Press "DOWN" to select °F, press "UP" again to select °C. The chosen temperature

unit will ash.

Press "SET" to conrm. The green LED will stop ashing, press "SET" again for the

calibrator to return to operation mode.

In order to keep good operation, please lock the values after the temperature

unit changed.

To do this –

• Press the " " button three times, red LED on the rst line displays ,the

green LED on the second line displays "OFF".

• Press "UP" button two times, green LED will display

• Finally press "SET" to complete.



Turning off the power at high temperature will damage the sensor/heating parts

of the calibrator, therefore reduce the temperature to 50 °C after measurement.

When the temperature is reduced to 50 °C the user can then turn off the power.



This section shows you in detail how to operate the instrument temperature

controller using the front control panel. Using the front panel key-switches

and LED display the user may monitor the well temperature, the heater output

power and adjust the controller proportional band. The control buttons (SET,

DOWN, UP) are used to set the calibrator temperature set-point.



The digital LED display on the front panel allows direct viewing of the actual

well temperature. This temperature value is normally shown on the display.

The temperature is displayed in units, °C or °F, to the right.



The temperature set-point can be set to any value within the range and with the

resolution as given in the specications. Be careful not to exceed the safe upper

temperature limit of any probe inserted into the well.

• Press "UP" to increase temperature, or press "DOWN" to lower the temperature.

The temperature will be changed in 0.1° increments every time the button

is pressed.

Pressing and holding down the button the temperature will change in

1° increments.

The green LED display on the front panel will indicate the actual set

temperature.

When the set temperature changes, the values will ash.

• Release the "UP" or "DOWN" button and then press the "SET" button.

The calibrator will automatically control the target assembly temperature to

reach the set temperature in the stated time. The red LED display will indicate

the temperature of the target assembly.



The calibrator has been designed with the utmost care. Ease of operation

and simplicity of maintenance have been a central theme in the product

development. Therefore, with proper care the instrument should require

very little maintenance. Avoid operating the instrument in dirty or dusty

environments.

If the outside of the instrument becomes dirty, it can be wiped clean with a

damp cloth and mild detergent. Do not use harsh chemicals on the surface, as

they may damage the paint.

The calibrator should be handled with care. Avoid knocking or dropping the unit.

If the instrument is used in a manner not in accordance with the equipment

design, the operation of the instrument may be impaired and/or safety hazards

may arise.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ETI Prüfgeräte Handbücher

ETI

ETI PI-4000B Bedienungsanleitung

ETI

ETI 813-513 Bedienungsanleitung

ETI

ETI UAL/CL2 Betriebsanleitung

ETI

ETI PI-2500 Bedienungsanleitung

ETI

ETI PI-6000 Bedienungsanleitung

ETI

ETI PI-800 Bedienungsanleitung

ETI

ETI PI-800-GEN2 Bedienungsanleitung

ETI

ETI PI-5000 Bedienungsanleitung

ETI

ETI PI-2500-G2 Bedienungsanleitung

ETI

ETI Dry-Well 3101 Bedienungsanleitung

ETI

ETI 822-950 Bedienungsanleitung

ETI

ETI pH Pal Plus Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung