ETM DeltaBlue Bedienungsanleitung
OUTDOOR IOT EDGE SOLUTION
DeltaBlue
Quick Start Guide
Get started: This guide helps with initial product setup. Need more? Find
additional product information by simply scanning the QR code.
FEATURES
PIN DESCRIPTION
• Up to 3 years battery life time* (Depending on settings)
• Integrated 7-channel data logger
• Integrated 2G/3G/4G wireless modem
• Integrated GPS, temperature, humidity and accelerometer
• Pre-configured for the most common sensor types with 3.6V, 5V & 16V power
feed.
• Easy access to logged measurements via ETM’s IoT Cloud Dashboard (EWO)
• Easy integration to SCADA and telemetry systems
INTRODUCTION
DeltaBlue is a battery-powered, rugged device used for measuring and
control in remote areas or installations without acces to mains power or
a fixed communication line.
Common applications include:
• Well and Pit monitoring
• Tank measurments
• Water and sewer treatment
Channel Color Dip Switch OFF Dip Switch ON
1 IO Brown DI, Pulse DI, Pulse Strong Pullup
2 IO Blue DI, AI 0-2.5V AI 4-20mA
3 IO Yellow DI, AI 0-2.5V AI 4-20mA
4 IO Green DI, AI 0-2.5V AI 4-20mA
5 IO Red DI, AI 0-2.5V AI 4-20mA
6 IO Black AI 0-5VDC AI 0-10VDC
7 Feed Orange 1. 5V Out 2. 16V Out 4. 3.6V Out (Battery)
8 GND Grey Signal Ground
ACCESSORIES LED INDICATOR
Pressure Sensor Temperature/Humidity
Sensor
External Antenna
GSM
Connector
GPS
Connector
Replacement battery Stainless steel
mounting plate
Green status LEDs
1
Network
Slow Flash
2x Flash 3s Pause
3x Flash 3s Pause
4x Flash 3s Pause
Searching for network connection
Active 2G network connection
Active 3G network connection
Active 4G network connection
2
IP status
On
O
Internet provider connection
No Internet provider connection
3
Data Com
On
O
Rapid Flash
Recieving data (2s active)
No data transmittion occurring
Sending Data
Yellow signal strength LEDs
1
Poor
Flashing
On
O
RSSI < -105dBm or No SIM detected
RSSI ≥ -105dBm (Poor signal)
Not registered to mobile network
2
Fair
Flashing
On
O
No SIM detected
RSSI ≥ -89dBm (Fair signal)
RSSI < -89dBm or not reg. to mobile network
3
Good
Flashing
On
O
No SIM detected
RSSI ≥ -73dBm (Good signal)
RSSI < -73dBm or not reg. to mobile network
• Agriculture applications
• Remote alarms
• Lake water level monitoring
ETM Mätteknik AB (HQ)
Ekbacksvägen 32, 168 69, Bromma, Sweden
Tel: +46 (0)8 25 28 75 E-mail: [email protected]
www.etmiot.se
ETM Pacific Pty Ltd (APAC)
Suite 6, 273 Alfred Street, North Sydney NSW 2060, Australia
Tel: +61 (0)2 9956 7377 E-mail: sales@etmiot.com.au
www.etmiot.com.au
Welcome to your ETM Product
Support: ETM oers multiple support options to help you
get the most out of your product. You can go onto
If urgent, please call us using the numbers below.
Screw mount antenna
CONNECTING SIM CARD
WIRING EXAMPLES
• Water/Electrical meter
• Pressure Sensor
BATTERY AND COMMUNICATION
1. Start the configuration tool
2. Connect the unit to your computer
3. Go to the terminal tab, use ”Set COM Port” to choose the right COM port (most
likely not COM1) and set the baud rate to 115200
4. Open the port by pressing ”COM(X): CLOSED”
5. Click anywhere in the blue window until you see a flashing square. Proceed by
pressing the ”reset” button on the modem, then immediately press ”Esc” on your
keyboard until the message ”Escape Pressed” shows up
6. Make sure the that the firmware matches the configuration tool version like the
picture above (6)
7. The unit is now ready to be configured.
General settings
Used for adding phone numbers, change Unit ID, Clock sync, data formats...
Channel settings
Setting up and configuring alarms on dierent channels/pins.
Data Transfer/Logging Timers
For data logging/monitoring. Choosing which data the unit will gather and send.
Communication
Specify where the unit should send the data.
1. When done configuring the unit, press the red button ”WRITE MEMORY” to
upload the configuration to the unit.
2. To see what configuration is already on the unit, press READ MEMORY” when
having the unit connected to the computer to read it onto the configuration tool
3. To save your configuration to use for future units press ”File” in the top left corner,
then ”save” in the dropdown menu, and save it to an optional location.
4. Your unit is now ready to use.
2. CONFIGURATION TOOL 3. CONFIGURING THE UNIT
ETM PRODUCTS
DeltaBlue
Outdoor and
battery-powered
remote monitoring,
alarming & logging
solution
DeltaBlack
Industrial cellular
remote monitoring,
alarming & logging
solution
ETM-Purple
Intelligent cellular
2G/3G/4G
with ”last gasp”
ETM-770
Cellular Network
Monitoring tool
Cat M1/NB-IoT
2G/3G/4G
4. EWO (ETM WEB OFFICE)
To access the ETM IoT Cloud Dashboard, please visit the
website or scan the QR Code.
www.etmweboce.com/EWO/pages/login.jsp
• Log in using the provided login credentials
• Manage your account, units and organisation in the settings.
• Under settings > configuration choose which data you want to be presented
• Enjoy your ETM product
3.
3.
3.
4.
5.
6.
6.
1.
3. 2.
Getting Started
1. Connecting the hardware
ETM
Andere Handbücher für DeltaBlue
1
Dieses Handbuch passt für folgende Modelle
2
Andere ETM Datenlogger Handbücher
