ETM Purple Bedienungsanleitung

Intelligent Tri-Mode Terminal – ETM Purple

Features:

◩ Intelligent Tri-Mode Terminal, AT mode, ET Mode, JET Mode

◩ SMS, IP or CSD operation and/or configuration options

◩ Small form factor, to fit under meter covers or other enclosures with size constraints

◩ 2G (GSM/GPRS) Connectivity

◩ 3G (HSPA/UMTS) Connectivity

◩ 4G (LTE) Connectivity

◩ Combined or separate RS232 Serial & Power Connectors

◩ High speed USB

◩ RS422 and RS485 functionality

◩ Signal strength LED indicator

◩ 5 - 35V power input. 7 - 35V for last Gasp variants

◩ FME M antenna connector

ETM Purple user guide. 1802-20170003 R07

ETM-Purple User Guide

Contents

Contents ............................................................................................................................................ 2!

Revision History................................................................................................................................. 3!

Introduction........................................................................................................................................ 3!

Nomenclature................................................................................................................................. 3!

Overview ........................................................................................................................................ 3!

Applications.................................................................................................................................... 3!

Tri-Mode Operation........................................................................................................................ 4!

Physical Dimensions ......................................................................................................................... 5!

Separate Power RJ12 & Serial 10 pin Boxhead Connector .............................................................. 5!

Combined Power & Serial RJ45 Connector ...................................................................................... 6!

USB Communications Port................................................................................................................ 6!

Antenna ............................................................................................................................................. 6!

SIM Card ........................................................................................................................................... 6!

SIM!Pin!......................................................................................................................................................!7!

Indicator Lights .................................................................................................................................. 7!

LED Behaviour - Normal Start Sequence ...................................................................................... 7!

Green LEDs ................................................................................................................................... 8!

Orange LEDs ................................................................................................................................. 8!

Installation ....................................................................................................................................... 10!

Initial Start-up & Configuration......................................................................................................... 10!

Typical Startup Sequence............................................................................................................ 10!

ET Mode/Configuration.................................................................................................................... 11!

Putting the Unit into ESC Mode ................................................................................................... 11!

ET Command Table..................................................................................................................... 12!

Last Gasp Mode Operation ............................................................................................................. 14!

AT Mode Operation ......................................................................................................................... 15!

Common useful AT commands for basic operation include:........................................................ 15!

SMS Specific Commands ............................................................................................................ 16!

AT Commands for Incoming Circuit Switch Data Calls................................................................ 16!

JET Mode Operation ....................................................................................................................... 16!

JET Command table .................................................................................................................... 16!

JET!Configuration!change!responses!.......................................................................................................!18!

Installing the configuration tool in Windows 7. ............................................................................. 19!

Local!configuration!.................................................................................................................................!25!

Page 3 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

Revision History

Date

Revision

Editor

Description

2016-05-01

201605RV01

Patrick Paffard

First released version

2016-05-13

201605PRV02

Carl Håkansson

Added signal strength picture,

Added LED behaviour from Main code

2017-02-13

R03

Christian Leierer

Added Last Gasp information

2017-02-22

R04

Christian Leierer

Change parameters in tables

2017-06-13

R05

Carl Håkansson

Added config tool information

2017-08-04

R06

Carl Håkansson

Changed Nomenclature

2017-08-04

R07

Carl Håkansson

Changed part numbers

Introduction

Nomenclature

The ETM Purple variants incorporate the Cinterion BGS2, BGS5, EHS5, EHS6 or ELS61 module

and are intended for worldwide use (network and regulatory approvals permitting).

Terminal Nomenclature/History

Description

Part

number

Module

Installed

ETM Purple 2G, RJ12, Boxhead

71271

BGS2-E

ETM Purple 2G, RJ12, Boxhead, USB

71272

BGS5-E

ETM Purple 2G/3G Penta Band, RJ45, USB

71280

EHS6

ETM Purple 2G/3G Penta Band, RJ12, Box head, USB, Last Gasp

71284

EHS6

ETM Purple 2G/3G/4G, E-band, RJ45, USB

71423

ELS61-E

ETM Purple 2G/3G/4G, RJ12, Boxhead, USB, Last Gasp

71426

ELS61-E

ETM Purple 3G/4G US-Band, RJ45, USB

71355

ELS61-US

ETM Purple 3G/4G US-Band, RJ12, Boxhead, USB, Last Gasp

71356

ELS61-US

ETM Purple 3G/4G AUS-Band, RJ45, USB

71357

ELS61-AUS

Overview

The ETM Purple range of products, are intelligent industrial terminals designed for M2M (Machine

to Machine) communications. With 2G/3G & 4G connectivity, intelligent Tri-Mode operation and

small form factor they provide the ideal communications solution for electrical metering or other

applications utilising serial communications.

Applications

Typical applications include:

◩RS232, RS422/485 or USB communications interface for electrical meters and data

concentrators

◩Serial communications interface for other devices such as PLC’s, Irrigation controls, Security

and/or access systems, data loggers

◩As a device for sending SMS alarms notifications based on AT commands from a connected

PLC, PC or Server

Page 4 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

Tri-Mode Operation

The unit can be operated in a number of ways to achieve different functional outcomes, depending

on the requirements of the device to which the unit is connected, and/or the interaction with any

back-end/server. The ETM Purple can support CSD or IP connections and SMS configuration or

status queries.

The following is a simplified block schematic to assist in understanding the operational capabilities

of the unit.

Mode/Command

Structure

Purpose

Interface Method

ET Commands

The external processor is used to control

the start sequence of the modem and

make default operational settings. It is also

used to configure "Last Gasp" functionality

(if applicable) and other features.

ET commands sent to serial

port if in ESC mode

SMS of a subset of ET

commands sent to the units

phone number (note SIM needs

to have SMS activated)

AT Mode

Depending on the setting made above the

unit can be operated as a basic 2G/3G/4G

modem using AT commands to drive the

unit

AT commands sent to the serial

or USB port

JET Mode

Provides intelligent operational functions

such as;

- TCP tunnel

- CSD tunnel

- TCP Server

- Serial to TCP Server

- Status Logging > sending to server for

monitoring (by others)

JET commands sent to the

serial port, or by SMS or by

TCP

Note that there may be a charge associated with the provision of JET code, and that it is possible

for customers to use the modem and to load their own Java™ code for a specific application. ETM

will not provide un-compiled JET code for use by others, it is the customers responsibility to

develop their own code using the resources available for the BGS5, EHS5, EHS6 or ELS61

module.

External Processor

ET Commands

Java Engine

JET Mode

EHS5/6 Wireless Module

AT Commands

ETM Purple Tri-Mode Intelligent

terminal

RS232 Serial

ET Mode

AT Mode

JET Mode

USB

AT Mode

(Modem Can be

Page 5 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

Physical Dimensions

Separate Power RJ12 & Serial 10 pin Boxhead Connector

Some models of ETM Purple utilises a 6-pin RJ12 connector for power, pin allocations are shown

below.

Function

Looking at Modem Socket

Power Supply (+5 to +35VDC) (+7 to 35VDC

for Last Gasp)

Not Used

GND

Some models of ETM Purple utilises a 10-pin box head connector for communication, pin

allocations are shown below.

Function

Looking at Modem Socket

DCD Out

DSR Out

RXD Out

RTS In

TXD In

CTS Out

DTR In

RING Out

GND

Not Used

70.0

52.0

24.0

110

Approx.

SIM Cover

RJ45 Serial & Power Connector

Mini-USB Connector

123456

Page 6 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

Combined Power & Serial RJ45 Connector

Some models of the ETM Purple utilises a single RJ45 combined power and serial connector, pin

allocations are shown below.

Function

Looking at Modem Socket

Power Supply (+5 To 35VDC, 400mA @ 12VDC)

(+7 To 35VDC for Last Gasp)

DCD

DTR

GND

CTS

RTS

USB Communications Port

Mini-USB port for communications directly to the EHS6 module within the modem, drivers for

Windows need to be installed on the PC to allow access to this port.

The modem can be powered from the USB assuming the USB can deliver a voltage in the range of

+5 to 35VDC(+7V to 35V Last Gasp), if not a separate power supply via the RJ45 connector is

required.

Note: The NES DCN3000 data concentrator can be set to 12VDC output USB power.

AT commands and responses are available via the USB port.

Antenna

The ETM Purple has a standard FME M antenna Plug on the end of an approximately 110mm

cable.

FME M Antenna Connector

SIM Card

The SIM card connector is located on the underside of the ETM Purple Terminal. The unit supports

both 3V or 1.8V SIMs. Any SIM card used needs to be correctly provisioned for the services and

network upon which it is intended to be used.

If the terminal is intended to be used for remote access to a device a terminating data number for

Circuit Switch Data (CSD) will need to be provisioned by the network operator, this number will

usually differ from any voice/SMS number. Other key configuration settings are;

◩Telstra NextG® SIMs when used for CSD require 2620 bearer capability

Caution

Take care to ensure that only

the correct connectors are

used or mechanical damage

to the pins may result.

Caution

Always disconnect power supply before

inserting or removing SIM Card.

Care should be taken in inserting and

removing the SIM card so as not to

damage the SIM holder or cover.

12345678

Page 7 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

SIM Pin

If the SIM used has a PIN either;

•The unit can be configured to enter the SIM pin, refer applicable section of this manual

•The SIM PIN should be deactivated, insert the SIM in a mobile phone and deactivate then

transfer the SIM into the ETM Purple unit.

Indicator Lights

Looking at underside (SIM access side) of unit.

LED Behaviour - Normal Start Sequence

LED 1

LED 2

LED 3

LED 1

LED 2

LED 3

Green!LED1:!ON!

Green!LED2:!ON!

Green!LED3:!ON!

Green!

LEDs!

remain!

ON!

Orange!LED1:!ON!

(Indicating!that!Module!has!been!found)!

Orange!LED2:!ON!

(Indicating!that!Module!has!been!powered-up!OK)!

Orange!LED3:!ON!

(Indicating!that!SIM!card!has!been!found)!

All!LEDs!

turn!OFF!

Orange!LED1:!Flashing!!4times!

Orange!LED2:!Flashing!!4times!

Orange!LED3:!Flashing!!4times!

All!LEDs!turn!

OFF!

Then!See!LED!Behaviour!Below!

Page 8 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

Green LEDs

Green LED 1

Function

Slow Flash 500ms On / 500ms Off

Searching for mobile network

Double Flash 3s Off / 100ms ON / 100ms

OFF / 100 ms ON

Active 2G network connection

Triple Flash 3s OFF / 100ms ON / 100ms

OFF / 100 ms ON / 100ms OFF / 100ms

Active 3G network connection

Four time Flash 3s OFF / 100ms ON /

100ms OFF / 100 ms ON / 100ms OFF /

100ms ON / 100ms OFF / 100 ms ON

Active 4G network connection

Green LED 2

Function

Internet Service Provider connection (Active PDP

context and IP address)

OFF

No Internet Service Provider connection

Green LED 3

Function

Rapid Flash

Sending Data

Receiving data from host (turn off after 2 seconds)

OFF

No data transmission occurring

Note: All LED will flash at boot up

Orange LEDs

Orange LED 1

Function

Flashing

RSSI < -105 dBm or no SIM detected

RSSI ≥-105 dBm (Poor signal)

OFF

Not registered to mobile network ≥

Orange LED 2

Function

Flashing

No SIM detected

RSSI ≥-89 dBm (Fair signal)

OFF

RSSI < -89 dBm or Not registered to mobile network

Orange LED 3

Function

Flashing

No SIM detected

RSSI ≥-73dBm (Good signal)

OFF

RSSI < -73dBm or Not registered to mobile network

Page 9 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

-110 dBm

(no signal)

<-100 dBm

(poor signal)

-100 to -86 dBm

(fair signal)

-85 to -70 dBm

(good signal)

> -70 dBm

(excellent signal)

Signal strength levels.

Page 10 of 36 For Support Contact +46 25 28 75

or [email protected]

1802-20170003 07 ETM Purple user guide.docx

Installation

1. Connect a suitable serial interface to the modems RJ45 port or 10 pin box header depending

on model, see previous section for pinout details.

2. Fit a suitable antenna to the unit’s FME antenna lead.

3. Install a SIM card enabled for the services you intend to use. If the terminal is intended to be

used for Circuit Switch Data (CSD) a SIM with a terminating data number will need to be

provisioned by the network operator, this number will usually differ from any voice/SMS

number. Note that for Telstra you will need to request;

2620 bearer capability (Telstra NextG™ Sims)

4. Connect the power supply. (The unit accepts a broad range of voltages from +5 to +35VDC)

5. Refer to related sections of this manual for information on configuring the unit for the intended

mode of operation.

Initial Start-up & Configuration

The unit may be delivered in the following states depending on customer request, note that

additional costs may apply for certain functionality.

As delivered

State

Description

Start-Up

Standard – no

JET Code

Basic modem that may be

controlled by AT

commands from devices

such as a PC, electrical

meter or PLC

When the units power is connected and the

start-up sequence completed (approximately 20-

30 seconds) the serial and USB ports will

become available at the set baud rate for AT

commands

With JET Code

When JET code is

installed in the unit custom

functionality become

available

When power is connected and the start-up

sequence completed (approximately 20-30

seconds) the serial and USB ports will become

available at the set baud rate for AT commands.

Note that dependant on the JET code and actual

state the serial and/or USB ports may not be

accessible as they may be busy.

Depending on the configuration settings

associated with the JET code the JET code may

auto run or be manually started

Typical Startup Sequence

AT commands may now be sent to the unit.

Andere Handbücher für Purple

Inhaltsverzeichnis

Andere ETM Touch-Terminal Handbücher

ETM

ETM ETM9900(J) Bedienungsanleitung

ETM

ETM Purple Bedienungsanleitung

ETM

ETM ETM9420-1 Bedienungsanleitung

ETM

ETM ETM8140-1 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung