ETS 5482 Bedienungsanleitung

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210107

Humidification System

Model 5482 Operating Manual

 
 www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 2of 14 
Table of Contents 
 
I. Important Safety Information..................................................................3 
II. Description of Contents..........................................................................4 
III. Set-Up Guide .........................................................................................5 
IV. Quick Start Guide ..................................................................................7 
V. Functionality...........................................................................................9 
VI. Repair and Maintenance .....................................................................11 
VII. Troubleshooting .................................................................................13 
VIII. Warranty ...........................................................................................14 
 
 
Revision History: 
Revision A: Released 2019-04-01. Initial release 
Revision B: Released 2019-07-22. QOL additions, Functionality section renamed to Operation Guide, 
Section numbers corrected. 
Revision C: Released 2019-10-29. Edits to section V. Operation Guide. 
Revision D: Released 2021-02-12. Manual update for current iteration of Model 5482. 
 
Products described in this manual are designed and assembled in the U.S.A. by 
Electro-Tech Systems, Inc. 
700 West Park Avenue 
Perkasie, PA 18944 
 

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 3of 14

I. Important Safety Information

SAFETY INSTRUCTIONS

The equipment described in this manual is designed andmanufactured to operate within defined design

limits. Any misuse may result in electric shock or fire. To prevent the equipment from being damaged,

the following rules should be observed for installation, use and maintenance. Read the following

safety instructions before operating the instrument.

POWER

POWER CORD: Use only the power cord specified for this equipment and certified for the country of use. If the

power (mains) plug is replaced, follow the wiring connections specified for the country of use. When installing or

removing the power plug, hold the plug, not the cord.

The power cord provided is equipped with a 3-prong grounded plug (a plug with a third grounding pin). This

is both a safety feature to avoid electrical shock and a requirement for correct equipment operation. If the outlet

to be used does not accommodate the 3-prong plug, either change the outlet or use a grounding adapter.

FUSES: Replace fuses only with those having the required current rating, voltage, and specified type such as

normal blow, time delay, etc. DO NOT use makeshift fuses or short the fuse holder. This could cause a shock or

fire hazard or severely damage the instrument.

OPERATION CAUTION

DO NOT OPERATE WITH COVERS OR PANELS REMOVED. Voltages inside the equipment consist of

line (mains) that can be anywhere from 100-240VAC.

DO NOT OPERATE WITH SUSPECTED EQUIPMENT FAILURES. If any odor or smoke becomes apparent

turn off the equipment and unplug it immediately. Failure to do so may result in electrical shock, fire, or

permanent damage to the equipment. Contact the factory for further instructions.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE: Operating the equipment in the presence of

flammable gases or fumes constitutes a definite safety hazard. For equipment designed to operate in such

environments the proper safety devices must be used such as dry air or inert gas purge, intrinsic safe barriers

and/or explosion-proof enclosures.

USE DISTILLED OR DEIONIZED WATER SOURCE FOR HUMIDIFICATION. Build-up of contaminates on

the transducer will cause stress to the transducer and electronics and resulting in premature failure and

invalidate the warranty.

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 4of 14

II. Description of Contents

Item

No.

Item

Qty.

Description

Ultrasonic Humidifier

The ultrasonic humidifier features a primary control base

unit and top-mounted mist generation basin.

Water tank

One 5-gallon water tank is included as standard. Optionally,

the humidification system can be connected directly to a DI

water supply.

Water tank spout adapter

One adapter is included to neatly allow for 1/4” tubing to

quickly connect and disconnect from the water tank.

1/4” OD polyethylene

tubing

One 10-foot length of tubing is provided to connect the

water tank to water supply inlet on the humidifier.

1” ID flexible PVC tubing

Two 1.5-foot lengths of tubing are provided to be used for

connecting the mist out port and closed-loop to the

humidification environment.

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 5of 14

III. Set-Up Guide

Part 1: Prepare water supply

Step 1 –Fill Water Tank

Remove cap with spigot attachment, and fill

tank up to intended level, up to five gallons,

with de-ionized or distilled water only.

Use of tap water will cause build-up of

contaminates and cause stress to the mist-

generating elements, which may result in

premature failure.

Step 2 –Install Dispensing Cap

Hand-tighten dispensing cap onto water tank.

Caution: DO NOT use any tools, over-

tightening the cap will damage the gasket and

cause water leakage.

Ensure the water tank tap lever is pointed right

in the “OFF” position, as depicted.

Loosen the small white cap to allow water to

flow freely.

Step 3 –Install Water Feeding Tube

Place water tank above humidifier.

Insert 1/4” OD tubing firmly into the

“DEIONIZED WATER IN” port on the humidifier.

Test the connection by gently tugging on the

tubing.

Optionally, utilize a water line in place of the

water tank. Caution: Water line pressure

cannot exceed 50 psi.

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 6of 14

Part 2: Prepare Unit for Operation

Step 1 –Check Drain Valve position

Ensure the drain valve is set to the “OFF”

position with the tap lever turned 90° from the

drain valve inlet and outlet.

Ensure humidifier is placed on a level surface

with no more than 5° tilt.

Step 2 –Turn on Water Valve

Ensure feeding tube is fully inserted.

Switch the water tank tap lever to the “ON”

position (to the left) for water to flow freely.

Loosen the small white cap to allow water to

flow freely.

Step 3 –Identify AC line cords

The AC line cord is to be connected to 100VAC

- 240VAC single-phase AC.

Note: This AC line cord is normally plugged in

the humidity AC outlet of a controller to

regulate mist output.

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 7of 14

IV. Quick Start Guide

Quick Start Guide

Step 1 –Apply Power and Fill Water Basin

Plug the three-prong AC line cord into a standard

wall outlet to test the functionality of the

humidifier.

The humidifier LED turns red while the water fills

the unit to an acceptable level. This process

should take between 1 to 2 minutes.

Note: Base Unit must be placed on a level

surface with no more than 5° tilt.

Step 2 –Mist Generation

After the water reaches an acceptable level, the

LED will turn green to indicate system has

enough water to produce mist.

Step 3 –Connect to Controller

Concluding the function test, remove the three-

prong AC line cord from the wall outlet and

connect the cord to a controller in the appropriate

operating system outlet, labeled “HUMIDITY”.

The Model 5482 can now be controlled to

produce mist and raise humidity.

Step 4a –Closed-Loop Humidification

Connect the two 1.5-foot sections of 1” ID tubing

to the humidifier. Connect one tube to the white

humidity outlet barb. Connect the other tube to

the black air inlet barb.

Connect the other ends of the tubing to the

environmental chambers input and output barbs.

The unit will recirculate and humidify a controlled

volume of air within a sealed environment.

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 8of 14

Step 4b –Optional Open-Loop Configuration

The humidifier can optionally be run in an open-

loop configuration, if desired.

Utilize one 1.5-foot section of 1” ID tubing and

connect from the white humidity outlet barb to the

intended environmental conditioning location.

The unit will pull external air to provide humidity

to an environment.

Step 5 –Humidity Setpoint

Install a relative humidity sensor within an

environmental chamber and plug into the rear

sensor socket of a Series 5000 controller. With

the sensor properly installed, on the rear of the

controller switch the back panel power switch to

on.

Create a set point by holding down the “ ” star

key on the controller and using the “ ” increase /

“ ” decrease buttons to enter the desired

humidity.

Switch the front panel “HUMIDIFY” switch to ON.

The controller will request humidification as

needed.

Consult the Operating Manual for the 5000

Series Controller for more details.

Step 6 –Humidity Indicator

The LED will turn green when the controller calls

for humidity.

As long as water level in the basin is at sufficient

level, mist can be produced.

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 9of 14

V. Functionality

1. The ETS Model 5482 Ultrasonic Humidification System requires a single-phase AC power

supply. It works with voltages from 100VAC to 240VAC.

2. The LED is a bi-color LED. It will turn red when de-ionized or distilled water falls below the

acceptable level in the basin. It will turn green when the Controller calls for humidity

production.

3. While the bi-color LED is red, the water solenoid is open to let de-ionized or distilled water fill

the basin to acceptable level.

CAUTION: IF RED LED IS STAYS ON FOR MORE THAN 3 MINUTES, UNPLUG THE AC

LINE CORD AND RE-FILL WATER TANK BEFORE RE-STARTING THE BASE UNIT.

Specifications

PERFORMANCE:

Humidification Rate: >125 mL/hour

Droplet Size: 5 microns

MECHANICAL

External Dimensions: 9.5” W x 7.0” D x 10.0” H

Material: Polycarbonate Construction

Weight: 4 lbs.

HARDWARE PORTS:

Two ¼ Inch Quick Connect

Two 1 Inch Hose Barbs

ELECTRICAL

Voltage: 100VAC to 240VAC, 50 to 60 Hz

Current: 1 Amp maximum

COMPATIBILITY

ETS Model 5100 or 5200 Series Controllers

www.electrotechsystems.com 833-ENV-GURU (833-368-4878) D01016 Revision D –20210115 - Page 10 of 14

Optional features and Accessories

The Model 5482 humidifier may optionally be purchased with in-line particulate filtering for

desired applications. The particulate filter serves to prevent contaminant build-up in the

humidifier basin and increase unit lifespan. Filter specifications include 99.999+% Bacterial

Filtration Efficiency (BFE), 99.999+% Viral Filtration Efficiency (VFE), and a flow resistance

of 1.5cm/H2O at 60 LPM.

The model 5482 humidifier can be optionally purchased with increased output capacity. The

model 5482-8595 high-capacity humidifier features dual outlet ports and hoses to rapidly

humidify an environment or to sufficiently humidify a large volume of air.

Inhaltsverzeichnis

Andere ETS Luftbefeuchter Handbücher

ETS

ETS 5462 Bedienungsanleitung

Beliebte Luftbefeuchter Handbücher anderer Marken

Bionaire

Bionaire CM1 Handbuch

Air-O-Swiss

Air-O-Swiss AOS 7131 Handbuch

KING

KING K 5002 Rainbow Bedienungsanleitung

Crane

Crane EE-6902 Bedienungsanleitung

Glaziar

Glaziar Ness Bedienungsanleitung

Philips

Philips DreamStation Go Abmessungen

Honeywell

Honeywell MISTMATE HUL520BC Bedienungsanleitung

Stadler Form

Stadler Form Hera Bedienungsanleitung

Hunter

Hunter 31206 Bedienungsanleitung

TaoTronics

TaoTronics TT-AH004 Bedienungsanleitung

adorini

adorini Cigar Heaven Bedienungsanleitung

Lanaform

Lanaform Aroma Bedienungsanleitung

Aprilaire

Aprilaire 800 Series Bedienungsanleitung

Pyle

Pyle SereneLife PHUMDIF8 Bedienungsanleitung

Trotec

Trotec B 200 Bedienungsanleitung

Pure Humidifier

Pure Humidifier EC Series Bedienungsanleitung

Crane

Crane EE-864 Bedienungsanleitung

air&me

air&me Solnan Bedienungsanleitung