ETS SA1-MPEA Bedienungsanleitung

SA1-MPEA Interface Instructions

The SA1-MPEA is a single channel, speaker driver and Power Over Ethernet IP camera Interface box. It contains a 10

Watt speaker power amplifier to drive an 8 Ohm speaker and is powered from the same ethernet cable that the camera

uses. The SA1-MPEA audio input is designed to connect to an IP camera’s audio output.

SA1-MPEA location and power

The SA1-MPEA should be placed within 6 feet of the IP camera. There are 2 modes of operation for the SA1-MPEA. In

mode 1 the SA1-MPEA is placed between the PoE switch and the IP camera. In Mode 2 the SA1-MPEA powered by its

own ethernet cable run going back to the PoE switch. A PoE plus network switch is recommended for mode 1 and is not

needed for mode 2. Note- in mode 1 the PoE sense resistor should be switched “OUT” and for mode 2 it should be

switched “IN”.

Speaker Cable

The speaker cable should be 18guage 2 conductor and can be up to 300’ long.

Adjusting the speaker volume

Adjust the audio input level for an acceptable volume level on the connected speaker beginning with the gain switch in the

low position. If a decent amount of volume cannot be achieved, place speaker gain range switch in the “High” position.

SA1-MPEA Mode switch: The SA1-MPEA supports Both Modes A and B of IEEE802.3af POE. The SA1-MPEA is pre-

configured for the most common use of the “end point” POE IEEE802.3af standard (mode A). If the power LED does not

illuminate in this position, try the mode B position (mid span).

Caution

It may be against the law to install this microphone kit in certain environments. It may also be against the law to record

conversations of the person(s) being monitored without their knowledge. It is the responsibility of the installation company

and end-user to determine if the application of this product is legal. These laws vary from state to state. If you are not

informed on these matters, consult a qualified attorney or contact the appropriate state agency. A sticker is provided with

this kit for the applications where notification must be posted.

Warranty

All ETS products carry a one year parts and labor warranty. This warranty does not cover damages as a result of misuse,

improper handling of the unit or exposure to extreme temperatures or moisture. At its discretion, ETS reserves the right to

repair or replace this unit under the conditions of the warranty. If you experience problems with your equipment call ETS

at: 505-888-3923 to obtain a return authorization number. Equipment requiring repair beyond the warranty period or units

that have been damaged or are not covered under the warranty can be repaired by ETS for a minimal cost under most

conditions.

Made in the USA

Inhaltsverzeichnis

Andere ETS Aufnahmegeräte Handbücher

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch