Eureka Forbes AQUAGUARD CREST UV +HOT Bedienungsanleitung

AQUAGUARD®

CREST UV HOT

CREST UV+HOT

Product installation should be done only by a trained Eureka Forbes Service Technician only.

1. Input water must be tested for Total DissolvedSolids (TDS) and Total Hardness

- Install the product in a dry ventilated place. Keep it away from direct sunlight, heating devices or areas below 10oC.

- The purifier should be placed in area which is free of ants/insects/otherpests.

- Ensure that the input tap water temperature is in the range of 10o-40oC.Avoid installation to ahot water tap as it can damage the filters.

2. The input water pressure to your water purifier should be within the recommended range (refer variant specific technical specifications table). If

the input water pressure is more than specified, installation of a PRV (Pressure Regulating Valve)** is mandatory. If the input water pressure is

less than specified, installation of an external booster pump** is recommended.

3. Ensure that the filters are flushed thoroughly and independently for 3-5 minutes to remove fine particles present in the filter, before the installation

of the unit.

4. After installation, run the purifier for 5-10 minutes and drain the water.

Input waterquality usage limitations:

1. If the input water iron content is more than that prescribed in the technical specifications, use of an iron remover** is recommended as a pre-

treatment.

2. If the input water turbidity is more than that prescribed in the technical specifications or comprises colloidal particles, use of a special filter** is

required as a pre-filter.

3. If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer**

is recommended (applicable only for RO variants).

4. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications.

**Available at an extra cost.

PRE-REQUISITES FOR INSTALLATION

PRECAUTIONS

SAFETY FEATURES

•To get hot/warm water, touch the respective switches

•After completing the heating/warming process, the indication will display that the product is ready to dispense hot/warm

water. If hot/warm water is dispensed before completing this process, the output water will not be hot (80°C)/warm

(45°C) respectively.

•To dispense hot/warm water, press the child lock and hold the dispense switch

•Do not let the glass/cup/container overflow with hot water while collecting water.

Note: Unless the child lock function is activated and the dispense switch is pressed & held within 10 seconds, hot/warm

water will not be dispensed.

•Hot water above 50°C may cause burns, due to scalding if touched with bare hand. Aquaguard®

“Hot” has an in-built safety feature, as “CHILD LOCK” especially for the safety of children/aged.

•Electronic thermostat cut-off is provided to prevent over heating of hot/warm water.

•As an additional safety measure, mechanical thermostat is provided which needs a manual intervention to check and restart

the product in case the thermostat trips due to overheating.

THE PROCESS OF PURIFICATION (For UV Variant)

Stage Treatment Materials Benefits

1 Sediment filter Multi-layered Polypropylene spun

cartridge over the carbon block Removes suspended particles such as dirt, dust, mud and sand from water. It removes very fine

turbidity from the water

2 Chemi-blockTM Dust-free Bacteriostatic Activated

Carbon block filter cartridge as a core Adsorbs colour, odour, excess chlorine & organic impurities from the incoming water. Its unique

Particle Trap Filter entraps any released micro particles.

3Mineral GuardTM Microcontroller-based electronic

impulse producer

Generates electronic impulses which prevent scaling / deposition of Calcium and Magnesium on

the Quartz Glass tube of the UV reflector

chamber, thereby ensuring best UV Penetration through Quartz Glass into the water column and at

the same time keeping essential minerals like Calcium and Magnesium intact in water

4UV e-boilingTM Germicidal UV Lamp UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses & protozoa,

thereby making it safe to drink.

5Active CopperTM with

Zinc Booster Cartridge*

A patented bacteriostatic taste enhancer

with double goodness of Active

Copper™ and Zinc Technology

Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory properties

that help to support healthy metabolism. It also helps to provide the body with energy and is much

needed for growth and development. Zinc also has a major role in the immune system. The

activated carbon removes organic components and polishes the water, giving it a sparkling look,

making it pure and great to taste.

*Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification

(Acceptable limit)

6Mineral MagnetTM

cartridge Patented multiple magnetic field

(MMF) generating device Breaks complex water molecules into fine micro-clusters, making water more bio-permeable, so

that your body can easily absorb the goodness of water, along with its much needed nutrients.

TECHNICALSPECIFICATIONS*

TECHNICAL

PARAMETER

SPECIFICATION

Model

AQUAGUARD

®CREST UV +HOT

PRODUCT SPECIFICATION

Dimension (W X D X H)

315 mm X 185 mm X 425 mm (Approx.)

Net weight

4.8 kg (Approx.)

Purification Technology

Standard Purification supplied

Combination cartridge (sediment + Carbon),

Mineral

guardTM, Active CopperTM with Zinc

Booster Cartridge, UV

- E-boilingTM, Mineral

Magnet

TM Cartridge

ELECTRICAL SPECIFICATIONS

Power Rating

20 Watts (Max.) in ambient mode.

785 Watts

in HOT/Warm mode.

Power Supply

Input 230VAC, 50Hz.

UV LAMP

11 Watts

UV Lamp life

8000 burning hours (as per UV lamp

manufacturer spec.)

Operating Voltage Range

150 to 280 V AC, 50 Hz

RECOMMENDED INPUT WATER PARAMETERS

Input

water pressure range**

.3 to 2 kg/cm2

Input

Iron content (Max.)

.1 mg/L

Input

Chlorine content (Max.)

.2 mg/L

Input

water turbidity (Max.)

NTU

Total

Dissolved Solids (TDS)

to 200 mg/L

Input

Water Temperature range

°Cto 40°C

*Technical Specifications are subject to change without prior notice.

Note: The performance data presented in the table is applicable under

standard laboratory conditions#.Actual performance may vary

depending on the input water quality, water pressure and condition of

filters.

**If the pressure is higher tan the maximum specified, use of a

pressure reducing valve is mandatory, If the pressure is lower than

minimum specified, use an external booster pump recommended

The above accessories are available with our company at an additional

cost.

Warranty Void if the product is not installed as per

recommendations.

*Standard Test Conditions:

Feed Water Quality: TDS Max: 200 mg/L

Pressure: 1 kg/cm2, Turbidity: 1 NTU (Max.), Temperature: 25°C,

Chlorine: below 0.2 mg/L, Iron: below 0.1 mg/L

Life: 6000#Liters

*Actual performance may vary based on input water conditions –

Turbidity& Pressure.

Indication Unit Status Indication Unit Status

Power ON- All LEDs will blink for 1 sec in Blue, Yellow and

Red.

Flush: Touch and Hold centre of LED Indication for 10 seconds. LEDs Rotate

Anti-clockwise. To stop flushing Touch the centre of LED Indication

again.(Caution: Do not drink the water which comes out during flushing

mode.)

Purification Process Filter Life Warning/ End of Life.

Warm Mode ON Temperature sensor fault. All LEDs will blink in Red at 0.5 sec rate.

Hot Mode ON UV Fault/LDR Fault. All LEDs ON for 0.5 seconds and OFF for 3 second

Ready to dispense -

All LEDs become solid.

Blue -Ambient water.

Yellow -Warm water.

Red - Hot water

SV Fault. All LEDs ON, OFF, ON for 0.5 seconds and Then OFF for 3

seconds. Cycle repeats

Dispensing - Touch the centre of LED indication; Single LED

rotates Clockwise

Blue -Ambient water.

Yellow -Warm water.

Red - Hot water

EA fault (If both 2 EA chip not connected or if main PCB to junction PCB

Harness is not connected) Led 2, 5 and 7 is solid. LED 1, 3 blinks @0.5

second rate

EA Fault: LED 2, 5 and 7 will be solid. LED 1,3 or only 1or 3 will

blink @ 0.5 second rate depending on the filters Combination Cartridge EA fault(Blue) LED 2, 5 and 7 is Solid. Led 3

[email protected] Second rate

Sleep Mode: If unit is not in use for 10 minutes, Unit goes to sleep

mode. To Activate Touch the centre of the LED indication

Active Copper cartridge with zinc booster EA fault(Beige) LED 2,5 and 7 is

solid. LED 1 blinks @ 0.5 Second rate

Switch OFF the power and water supply, If unit is not used for 3-4 hours

FUNCTION OF INDICATORS –LED DISPLAY

HOW TO DISPENSE WATER FROM AQUAGUARD®

Aquaguard®Hot, Warm and Ambient -Operation Guide

Step 1 Power ON Blue/Yellow/Red colored LEDs glow for 1 second in sequence

Purification process for 30 seconds to ensure 100% protection

Step 2

Purification ON

All LEDs glow Blue

Step 3 Dispense mode

Mode 1 Mode 2 Mode 3

Ambient/Room Temperature

Warm (500ml) Hot(500ml)

Approx. 45°Approx. 80°

Step 4 Start Dispense

Touch Water Drop Icon Touch Warm Icon Touch Hot Icon

Blue LEDs Blink in sequence,

Purified water gets Dispensed

Alternate Yellow LEDs Blink

Duration :Approx. 2 mins

Alternate Red LEDs Blink Duration

:Approx. 4 mins

LED Turn Solid Yellow Once water is

warm

LED Turn Solid Red Once water is

Hot

Touch Child Lock Icon

Touch and Hold Water Drop Icon(within 10 seconds)

Yellow LED glows in sequence Red LED glows in sequence

Purified warm water gets dispensed

Purified Hot water gets dispensed

Remove finger from water drop icon

Note: LED INDICATES RED for HOT water and YELLOW for WARM water

TIPS FOR SAFETYAND MAINTENANCE OFYOUR AQUAGUARD®UV HOT

1. Read attentively and understand the purifier and its functions before use.

2. Installation and service has to be conducted by authorized persons from Eureka Forbes Limited only.

3. Install the purifier at a location with more ventilation.

4. Ensure that the purifier is installed in a dry place. Do not expose to direct sunlight or heat sources.

5. Ensure that the installation height is ideal for comfortable reach for the user to avoid any accidental hot water spill.

(Approx. 5 feet)

6. Connect the purifier to 230V AC power socket, duly grounded. Use 500VA voltage stabilizers in case the voltage fluctuates.

7. Discard about 10 litres of water after installation or after replacing the filter cartridges.

8. Do not remove or insert the plug with wet hands.

9. Replace the filters when the end of life indicator is displayed by your purifier.

10. Ensure that the filter cartridges and spares used during service/replacement, are genuine and from Eureka Forbes only.

11. Always switch off and disconnect the power plug before maintenance or cleaning.

12. In case of any damage or incorrect functioning, immediately contact an authorized service center of Eureka Forbes Limited.

Do not to repair on your own.

LIFE OF CONSUMABLE CARTRIDGES

Consumable Components

Average Service Life

Combination Cartridge (

Sed + Chemi filter)

6,000

#litres

UV Lamp

8,000 burning

hrs*

Active

CopperTM with Zinc Booster Cartridge

6,000

#litres

Mineral

MagnetTM Cartridge

6,000

#litres

Note: Please refer Standard Test Conditions#for filter life.

*As per manufacturer’s spec.

WARRANTY TERMS & CONDITIONS*

1. The Products are warranted against manufacturing defects for a period of twelve (12) months from the date of original purchase.

2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorized agent adequate opportunity to inspect test and remedy them for which the

Customer will deposit the goods at its own expense, if so, required by the Company with the Company's Office/Service Centre along with the original invoice in the city where they are sold.

3. The Inspection and Test Report of the company's office/service centre will be final and binding under the warranty for determining defects, repairs / alterations required or carried out or certifying

work of the goods thereafter.

4. AQUAGUARD®may require initial setting, post-installation, depending on varying water conditions and power supply. In case of any service requirement, post-installation, please contact the

company's service centre.

5. The company or its authorized agent will be entitled to retain any defective part replaced under the warranty.

6. Notwithstanding anything to the contrary contained or implied by this warranty:

a) The company's liability under this warranty shall be limited to the first sale of the goods by the company to the customer and will not apply or extend to any secondary sale of goods by the customer.

b) The company's liability under this warranty shall be limited only to defects in the goods which occur under the conditions of normal operation of the goods and their proper and prescribed use. The

warranty does not cover or extend to defects which are determined by the company or its authorized agents as occurring or resulting from or attributable to negligence, abuse, misuse, faulty care,

operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods on electrical supply for which they are not designed, or damage caused by lightening

or other electrical disturbances or interruptions, dismantling or re-installation at a different location.

c) The company's liability under this warranty shall remain valid only if the goods are duly installed by the company or its authorized agency at the location specified in the invoice and such installation

is undertaken by the company or its authorized agent or franchisee.

d) Consumable items mentioned in the consumables table are subject to normal wear and tear are not covered by this warranty. Please refer model specific components given in the user manual under

the table “consumable cartridges”.

e) Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the date of installation, on the condition that the input water is as per the standard test

conditions for RO variants (provided in the section “Technical specifications table”), mentioned in the user manual. If the RO membrane gets clogged within warranty period, it will be

cleaned/repaired/replaced free of charge as deemed fit by the company authorized service person/centre after inspection. (At applicable for RO models only.)

f) The customer will have no claim against the company, its employees and its authorized agents or franchisees under or pursuant to this warranty in respect of death or injury to the customer or any

other person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or operation or utilization of the goods otherwise than in accordance with the user

manual or by due to any other cause or circumstances beyond the control of the company.

Inhaltsverzeichnis

Andere Eureka Forbes Wasserfiltersystem Handbücher

Eureka Forbes

Eureka Forbes Aquaguard select Active Copper Maxx Nrich Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard GLORY Bedienungsanleitung

Eureka Forbes

Eureka Forbes AQUAGUARD ASTOR Bedienungsanleitung

Eureka Forbes

Eureka Forbes Dr. Aquaguard MAGNA UV Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Blaze Bedienungsanleitung

Eureka Forbes

Eureka Forbes AUAGARD SURE DELIGHT NXT Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Eden Bedienungsanleitung

Eureka Forbes

Eureka Forbes Classic Aquaguard Bedienungsanleitung

Eureka Forbes

Eureka Forbes Under Sink RO Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Classic+ UV+Hot Bedienungsanleitung

Eureka Forbes

Eureka Forbes Dr.Aquaguard EDGE Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Pro RO Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Pro Universa 80SC Bedienungsanleitung

Eureka Forbes

Eureka Forbes AquaSure Aayush Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Verve Bedienungsanleitung

Eureka Forbes

Eureka Forbes dr. aquaguard classic uv+ Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Bedienungsanleitung

Eureka Forbes

Eureka Forbes Dr. Aquaguard Eterniti Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Astor GWPDARUTA00000 Bedienungsanleitung

Eureka Forbes

Eureka Forbes AQUAGUARD select Classic+ Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Aquasure Smart Plus RO+UV+MTDS Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard MIST UV+ Bedienungsanleitung

Eureka Forbes

Eureka Forbes Enhance Bedienungsanleitung

Eureka Forbes

Eureka Forbes Aquaguard Premier Active Copper UV+UF Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung