Eurofred Daitsu RHR-SCO2 Bedienungsanleitung

USER MANUAL

REMOTE CONTROL

RHR-SCO2

Serie

HEAT RECOVERY FRESHOME RHR

Edition

03/21

Models

RHR 150

RHR 200

Children over the age of 8, people with reduced physical or mental abilities and those with lit-

tle knowledge or experience may use this system provided they are supervised or have re-

ceived instructions on how to use the system safely and are aware of the associated dangers.

Children below the age of 3 must be kept away from the system, unless they are always supervised.

Children between the ages of 3 and 8 can only turn the system on and off, but always under supervision or if they

have received clear instructions on how to use the system safely and are aware of the potential dangers, and

provided the system has been placed and installed in the normal position of use. Children between the ages of 3

and 8 must not insert the plug into the socket, clean the system, make changes to its conﬁguration or carry out

any of the maintenance tasks that the user normally performs. Children must not play with the system

If you need a new power cable, always request the spare part from Daitsu to prevent dangerous situations from

occurring. Only qualiﬁed experts can replace damaged mains connections.

Keep the manual in a safe place close to the unit.

DAITSU

RHR-S WIRELESS CO2PROBE

Country: EN

CONTENT

1 ABOUT THIS MANUAL............................................................................................ 4

1.1 About the device .................................................................................................. 4

1.2 How to use this manual ........................................................................................ 4

1.3 Original Instructions .............................................................................................. 4

1.4 Warnings .............................................................................................................. 4

2 SAFETY................................................................................................................... 5

2.1 Directives.............................................................................................................. 5

2.2 Signs on the unit................................................................................................... 5

2.3 General safety instructions.................................................................................... 5

3 DESCRIPTION......................................................................................................... 5

3.1 Intended use ........................................................................................................ 5

3.2 Operating principle ............................................................................................... 5

3.2.1 Ventilation speeds and modes. .......................................................................... 6

3.2.2 CO2setpoint...................................................................................................... 6

3.3 Visual signals........................................................................................................ 7

4 OPERATION ............................................................................................................ 7

4.1 Show status ......................................................................................................... 7

4.2 Setting mode........................................................................................................ 7

5 INSTALLATION ........................................................................................................ 8

5.1 Preparation........................................................................................................... 8

5.2 Installation procedure ........................................................................................... 8

5.3 Start-up................................................................................................................ 9

6 CONFIGURATION.................................................................................................... 9

6.1 Conﬁguring settings.............................................................................................. 9

7 TECHNICAL DATA................................................................................................... 10

I 4

DAITSU WIRELESS CO2PROBE / INSTALLATION AND OPERATION MANUAL

1 ABOUT THIS MANUAL

1.1 ABOUT THE DEVICE

The wireless CO2probe is a user control and a CO2sensor for the ventilation system. The device communicates information

on the ventilation speed request and the system status via wireless communications with the central control device.

ALED status

BLED mode

CTouch button

1.2 HOW TO USE THIS MANUAL

1.3 ORIGINAL INSTRUCTIONS

1.4 WARNINGS

This manual is designed as a reference book for qualiﬁed installers to be able to install the wireless CO2probe (hereinafter

“device”) and for users to be able to use the device for its intended purpose. Make sure you have read and understood the

manual before installing and/or using the device.

The original instructions for this manual were written in Spanish. Versions of this manual in other languages are a translation

of the original instructions.

NOTE

It is used to highlight additional information.

DANGER

It identiﬁes a danger that could cause personal injury, including death.

I 5

DAITSU WIRELESS CO2PROBE RHR-SCO2

The device complies with the following EC directives:

 EMC Directive: 2004/108/EC

 Low Voltage Directive: 2006/95/EC

 RTTE Directive: 1999/5/EC

 RoHS Directive: 2002/95/EC

 WEEE Directive: 2002/96/EC

2 SAFETY

2.1 DIRECTIVES

2.2 SIGNS ON THE UNIT

Warning: Check the instructions for use as a precaution.

Danger: Risk of electric shock.

IEC 61140 Protection Class II (double insulation).

CE mark compliance.

Use of the device may not be legal in all member states.

Dispose of in accordance with European Community Directive 2002/96/EC (WEEE).

2.3 GENERAL SAFETY INSTRUCTIONS

 This product was designed and manufactured to ensure maximum safety during installation, operation and service.

 Always read the safety instructions before installing, maintaining or repairing the product and strictly observe these

instructions.

 Parts of the device carry mains power, which is a potentially lethal voltage.

 Disconnect the power supply to the supply line, circuit breaker or fuse before installing, repairing or removing the device.

 The device is designed for indoor use only. Do not expose the device to rain or moisture in order to prevent short circuits.

 A short circuit can cause ﬁre or electric shock.

 Operate the device between 0°C and 40°C.

 Only use a soft, damp cloth to clean the unit.

 Never use abrasive or chemical products. Do not paint the device.

3 DESCRIPTION

3.1 INTENDED USE

The device is designed for the following purposes:

1. To set the ventilation level via the fan speed, according to the user input or the measured level of CO2.

2. Conﬁgure the parameters for controlling the ventilation. Any other use or additional use is not in compliance with the

intended use.

3.2 OPERATING PRINCIPLE

The device communicates with the control device via wireless communications for controlling the ventilation. Via the button

and the LEDs, you can read and conﬁgure the control mode that the ventilation system is currently in. When it is in Eco mode

or Comfort mode, the device requests the ventilation level according to the amount of CO2in the air.

I 6

DAITSU WIRELESS CO2PROBE / INSTALLATION AND OPERATION MANUAL

3.2.1 VENTILATION SPEEDS AND MODES.

3.2.2 CO2SETPOINT

The ventilation system operates in one of the following modes. In each of these modes, the control device adjusts the

ventilation system to a conﬁgured ventilation level.

The device measures the level of CO2in the air continuously and compares the measured value to a conﬁgured setpoint.

The device controls the ventilation accordingly to keep the measured level of CO2below the requested level. When it is in

Comfort mode, the requested level is the same as the conﬁgured value. In Eco mode, the requested level is 250 ppm above

the conﬁgured value.

The control device drives the fan according to the highest values sent by the linked wireless sensors. When you start the timer

mode from this device, the ventilation will be active for 30 minutes.

ABSENCE MODE:

It represents periods of non-occupancy, when the heat recovery unit will operate at the lowest capacity.

MAXIMUM TIMER:

High fan speed, for a limited time. When the button is pressed, the heat recovery unit will reach maxi-

mum speed for 30 minutes.

ECO MODE:

Sensor-based automatic ventilation. In ECO, the system will begin at a higher CO2level to ventilate like

in COMFORT mode.

COMFORT MODE:

Sensor-based automatic ventilation. The system will accelerate the CO2-based ventilation after a certain

default activation value is exceeded.

AT HOME MODE:

It represents occupancy of the home or a room. By selecting this button, the heat recovery system

knows that there is one person (or more) in the room or home. It will set the speed to the default level.

NOTE

The device stores the fan speed values conﬁgured on the control device and requests them from there. The device

stores the CO2setpoint itself and does not communicate it to any other device.

I 7

DAITSU WIRELESS CO2PROBE RHR-SCO2

LED STATUS LED MODES

Start-up

STEADY WHITE ON ON ON ON ON

System status

STEADY GREEN <800 PPM

STEADY YELLOW 800-1900 ppm

STEADY

RED >1900 ppm

1 ﬂash Communication error

2 ﬂashes Dirty ﬁlter

3 ﬂashes Fan error

4 ﬂashes CO2sensor error

5 ﬂashes Low battery

Selection

ABSENCE MODE

OFF

AT HOME MODE ·

MAXIMUM TIMER ·

ECO MODE ·

COMFORT MODE ·

3.3 VISUAL SIGNALS

4.2 SETTING MODE

From the status screen:

1. Tap the button. The mode LEDs show the following selection.

2. If necessary, tap the button within 2 seconds, repeat until the selection shows the required mode.

3. Wait 2 seconds. The device applies the requested mode.

The LED status and the LED modes show the system status.

4 OPERATION

4.1 SHOW STATUS

1. Tap the button.

The LED status and the LED modes show the system status.

I 8

DAITSU WIRELESS CO2PROBE / INSTALLATION AND OPERATION MANUAL

5 INSTALLATION

5.1 PREPARATION

5.2 INSTALLATION PROCEDURE

DANGER

Disconnect the power supply to the supply line,

circuit breaker or fuse before installing the de-

vice.

DANGER

Make sure that the power supply is turned off.

1. Press the clip and pull the

upper section of the lower

section.

When the device is not placed in a recessed wall box:

1. Prepare the wall, if necessary. Use the mounting plate as a template.

2. Remove the detachable plastic from the cable entry on the housing.

2. Position the lower section

of the device.

3. Secure the lower section

with the bolts.

5. Position the upper section

of the device on the lower

section.

a. Position the clips.

b. Close and press until

it clicks.

2. Open the safety cover.

Use a small ﬂat-head

screwdriver to loosen

the clip.

1. Pass the power cable

through the rear hole (A)

or the cable entry (B).

4. Connect the power cable

to the bolt terminals.

NOTE

Do not place the device in a metal housing.

I 9

DAITSU WIRELESS CO2PROBE RHR-SCO2

6 CONFIGURATION

NOTE

When conﬁguring the fan speeds, make sure that the average fan speed is between the low fan speed and the

high fan speed.

5.3 START-UP

6.1 CONFIGURING SETTINGS

1. Enable the 230 V power supply.

All of the LEDs will light up for 3 seconds.

2. Wait until the status LED displays link mode.

If the device shows another indication, the device is already linked. See 6.2 on how to link the device again.

3. Make sure that the fan box is in link mode.

4. Tap the button. The device tries to link to the control device.

It displays the result in the LED status.

When the communication fails, make sure that the control device is in link mode and try again.

From the status screen (see 4.1):

1. Tap the button. The mode LEDs show the following selection.

2. If necessary, tap the button within 2 seconds, until the selection shows the element to be conﬁgured.

3. Keep the button pressed until the status LED starts ﬂashing white.

4. Release the button. The status LED shows the selected element, and the LED ﬂashing modes show its current value.

5. If necessary, tap the button within 10 seconds, until the mode LEDs show the value to be set.

6. Wait 10 seconds and the device will apply the conﬁgured value. The LED status and the LED modes show the system

status.

LED STATUS LED MODES

Conﬁguration

LOW SPEED

OFF

MEDIUM SPEED ·

HIGH SPEED ·

CO2SETPOINT ·

LINKING ·

VALUE

Blue/red Low speed Off 10% 20% 30% 40%

Blue/green Medium speed 30% 40% 50% 60% 70%

Red/green/blue High speed 60% 70% 80% 90% 100%

Blue (ﬂashing) CO2setpoint 700 ppm 800 ppm 900 ppm 1000 ppm 1100 ppm

Red/green Linking

I 10

DAITSU WIRELESS CO2PROBE / INSTALLATION AND OPERATION MANUAL

7 TECHNICAL DATA

DAITSU WIRELESS CO2 PROBE

TOTAL DIMENSIONS 100 x 100 x 25 mm (height x width x depth)

WEIGHT ± 125g

ENVIRONMENTAL

CONDITIONS

Temperature

Operating 0 to 40°C

Transport

and storage -20 to 55°

Relative humidity 0 - 90%, without condensation

Electrical protection (IEC60529) IP30

ELECTRICAL

SPECIFICATIONS

Main power supply 195 - 253 VAC, 50 Hz.

Maximum energy consumption 4 VA

Cable diameter 0.25 to 2.5 mm2

CO2MEASUREMENT

SPECIFICATIONS

Optimal measuring range

Measurement accuracy (within the optimal

range, >10 min after start-up):

400 to 2000 PPM.

Stabilization period after start-up 40 PPM + 2% of reading at 20°C 2 minutes

VERSION 1

Eurofred S.A.

Marqués de Sentmenat 97

08029 Barcelona

www.eurofred.es

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eurofred Fernbedienung Handbücher

Eurofred

Eurofred Daitsu ACVD Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Eurofred daitsu RHR-SCO2 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken