EUROSEC CP8L Bedienungsanleitung

CCPP

PP88

88LL

LLCC

CCDD

UUSS

SSEE

EERR

MMAA

AANN

NNUU

UUAA

AALL

USER.qxd 25/10/01 09:35 Page 1

Downloaded from www.ukpanels.com

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Full Setting the System . . . . . . . . . . . . . . . . . . . . 1

Part Setting the System (using Part 1) . . . . . . . . 2

Part Setting the System (using Part 2 or 3) . . . . . 2

Unsetting the System . . . . . . . . . . . . . . . . . . . . . 3

Display After Alarm . . . . . . . . . . . . . . . . . . . . . . . 3

Resetting After Alarm . . . . . . . . . . . . . . . . . . . . . 3

Programmable User Options . . . . . . . . . . . . . . . . 4

Zone Remove Option . . . . . . . . . . . . . . . . . . . . . 4

System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6

Turning Chime On/Off . . . . . . . . . . . . . . . . . . . . . 6

Programming User Codes . . . . . . . . . . . . . . . . . . 7 - 9

Setting Time & Date . . . . . . . . . . . . . . . . . . . . . .10 - 11

Reading the Log . . . . . . . . . . . . . . . . . . . . . . . . .12 - 13

Keypad Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Tamper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

System Details . . . . . . . . . . . . . . . . . . . . . . . . . . 14

USER.qxd 25/10/01 09:35 Page 2

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

Introduction

Welcome to the eurosec control panel. Your installation company will

have programmed your system to protect your premises to the highest

possible standards. Several user programmable options are available

that will be covered later in this manual.Throughout this manual refer-

ence will be made to the User Code, the factory set default is 5678.

This code is programmable along with eight other User Codes.

Full Setting the System

Two methods are available for Full Set.After checking the premises are

secure.

1) Press Quick

Enter a valid User Code followed by Full.

2) The exit tone will now sound.

3) Exit the premises via an authorised exit route .

Note: Pressing the Quick key during exit will shorten the exit time

to 3 seconds.

Note: To abort the exit enter a valid User Code.

USER.qxd 25/10/01 09:35 Page 1

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

Part Setting the System (using Part 1)

Up to three Part Sets may be available for your system.Please refer to

the customer details at the rear of this manual for information about

Part Set zones. Part Set zones will be omitted from the system when

that particular Part Set is used.To set the system using Part 1.

1) Press Quick followed by Part

Enter a valid User Code followed by Part

2) Retire to an unprotected area.

Part Setting the System (using Part2 or 3)

Two other Part Sets may be available for your system. Part 2 is a sec-

ond set of zones that may be omitted and Part 3 will combine Part 1

and Part 2.To use Part 2 or 3.

1) Press Quick followed by 2 or 3.

Enter a valid User Code followed by 2 or 3.

2) Retire to an unprotected area.

Note: Pressing the Quick key during exit will shorten the exit time

to 3 seconds.

Note: To abort the exit enter a valid User Code.

USER.qxd 25/10/01 09:35 Page 2

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

Unsetting the System

1) Enter the premises via an authorised Entry Point.

2) The Entry Tone will sound.

3) Proceed to the keypad and enter a valid User Code.

Display After an Alarm

After an alarm has occurred the system should be unset as above.The

display will show the zone that caused the alarm.

Resetting After an Alarm

After an alarm the system needs to be reset. To reset the system.

If Any Code Reset has been programmed.

1) Press Reset

If Master Code Reset has been programmed by the engineer.

1) Enter a valid User Code

2) Press Reset

Note: The terms of your insurance may prohibit User reset.

IfTamper reset has been programmed for Engineer Reset the

display will show “ !! Service Due !” for 3 seconds each time

the user attemts to set the system. Please contact your

installation company.

USER.qxd 25/10/01 09:35 Page 3

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

Programmable User Options

Several user programmable options are available via user codes 1, 2

or 3.To use these options please continue below.

Delete Zone Option

This option allows individual zones to be deleted (omitted) when the

system is being set. It is only applicable to the one Set state and will

need to be repeated for subsequent Sets. If you are removing particu-

lar zones on a regular basis ask your installation company to include

them in a Part Set.

1) Enter a valid User Code followed by No

the display will show:-

2) Press No

the display will show:-

3) Press YES

The display will show:-

4) Press the zone numbers

corresponding to the zones you

wish to delete from the set procedure.

The display will show for example:-

Do You Want to. .

Test ?

Do You Want to. .

Delete Zone ?

Enabled Zones . . .

1 2 3 4 5 6 7 8

Enabled Zones . . .

1 - 3 4 5 - 7 8

USER.qxd 25/10/01 09:35 Page 4

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

4) Press 0 twice

the display will show for example:-

5) Press Full for Full Set

Press Part for Part 1 Set

Press 2 for Part 2 Set

Press 3 for Part 3 Set

6) The system will now start the relevant Set with the zones

you deleted removed from the Set.

Note: This will be for the one Set state only.

System Test

This option allows the User to test zones, bells and strobes on the

system.

1) Enter a valid User Code followed by No

the display will show:-

2) Press Yes

the display will show:-

Do You Want to. .

Test ?

Walktesting . . . . .

O.k !

Do You Want to. .

Set User 1 ?

USER.qxd 25/10/01 09:35 Page 5

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

3) Violate each zone on the system (as you do so the

display will show the violated zone) to verify its integrity.

4) To test the bells (external sounders) and strobe press 9.

To stop the bell test press 9 again.

5) To escape back to Unset press 0 three times.

Turning Chime On/Off

Your installation company may have programmed a group of zones or

a single zone as Chime. This Chime function may be turned on or off

by the User.

1) Enter a valid User Code followed by No

the display will show:-

2) Press No

the display will show:-

3) Press No

the display will show:-

4) Press Yes

the display will show:-

5) The current Chime Mode will be

displayed. Use the No key to change

it to the mode you require.When

finished press 0three times to return

to the Unset mode.

Do You Want to. .

Test ?

Do You Want to. .

Delete Zone ?

Do You Want to. .

Select Options ?

Do You Want to. .

Program Chime ?

USER.qxd 25/10/01 09:35 Page 6

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

Programming User Codes

Up to nine user codes may be programmed on predetermined levels

these are.

User Numbers 1 to 3 Master Level

Allows Set, Part Set, Unset and User Programming Mode.

User Numbers 4 to 7 User Level

Allows Set, Part Set and Unset.

User Numbers 8 to 9 Set Only Level

Allows Set Only

User Number 1 is factory default 5678.This code may only be

changed.There is no facility for deleting this code.

All other codes may be changed or deleted as required.

To program User Codes.

1) Enter a valid User Code followed by No

the display will show:-

2) Press No

the display will show:-

3) Press No

the display will show:-

4) Press Yes

the display will show:-

Do You Want to. .

Test ?

Do You Want to. .

Delete Zone ?

Do You Want to. .

Select Options ?

Do You Want to. .

Program Chime ?

USER.qxd 25/10/01 09:35 Page 7

Downloaded from www.ukpanels.com

PPaa

aagg

ggee

5) Press No

the display will show:-

6) Press Yes

the display will show:-

7) Press a single digit corresponding

to the user number (1 to 9) that

you wish to program.

the display will show for example:-

8) To change the code press No

the display will show for example:-

(to delete a code enter 0000)

9) Enter your required code

followed by Yes

the display will show for example:-

10) To accept the current text press

Yes

To change the text press No

the display will show for example:-

Do You Want to. .

Program Codes ?

Select 1 . . 9

Code 2

# # # #

Code 2

0 0 0 0 <-

Code 2 Text

User 2

Code 2 Text

USER.qxd 25/10/01 09:35 Page 8

Downloaded from www.ukpanels.com

Andere Handbücher für CP8L

Inhaltsverzeichnis

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung