Eurotherm Invensys 3216 Bedienungsanleitung

MC23-GB –v1.00

Operating Instructions

Temperature Indicator with

Digital Communications



Type 3216cc

English

MC23-GB –v1.01

Contents

1INTRODUCTION TO THE CONTROLLER AND MANUAL 3

1.1 DESCRIPTION 3

2BASIC OPERATION 4

2.1 CONTROLLER LAYOUT (HOME DISPLAY) 4

2.2 KEYS 4

2.3 OPERATION 4

3USER LEVELS 5

3.1 UNDERSTANDING USER LEVELS 5

4SETTING UP THE CONTROLLER 6

4.1 CUSTOMER ID. 6

4.2 UNITS6

4.3 SCROLLING TEXT 6

5DIGITAL COMMUNICATIONS 7

5.1 DIGITAL COMMUNICATIONS –RS232 7

5.2 DIGITAL COMMUNICATIONS –RS485 7

5.3 COMMS ADDRESS 7

6NAVIGATION DIAGRAM 8

6.1 3216CC INDICATOR 8

7CONTROLLER FAULT 8

7.1 FAULT CODE DIAGNOSTIC TABLE 8

Quick Start Guide

MC23-GB –v1.01

1 Introduction to the Controller and Manual

1.1 Description

The model 3216 controller/indicator is made by Eurotherm, and is fitted by Carbolite Gero

configured for immediate use as an indicator. It is configured for the input (thermocouple)

type for which it was ordered.

The indicator does not contain a real-time calendar, and is not subject to century-end date

problems.

When the indicator is supplied fitted into a furnace or oven then it is usually on whenever the

Instrument Switch is on. When it is supplied in a separate box, then it is on whenever the box

is connected to the electrical supply.

The indicator will only show the correct temperature if it is also connected to type of

thermocouple for which it is configured.

Quick Start Guide

MC23-GB –v1.01

2 Basic Operation

2.1 Controller Layout (Home Display)

2.2 Keys

Page Key 

The Page key is used to access level 2 when held down

for 3 seconds.

Scroll Key 

The Scroll key is used to scroll through the parameters.

ACK

Page + Scroll



When pressed simultaneously the ACK function is used

to:

Return to the Home Menu.

Acknowledge an alarm if activated.

Reset a program after the program has ended

Arrow Keys



The arrow keys are used individually to adjust the

selected parameters and in combination to run a program

Note: If a parameter is selected and no further action is taken, the display will time out and

revert back to the home display in its working level after approximately 1 minute

2.3 Operation

No operator action is normally required.

When switched on, the indicator lights up, goes through a short test routine, and then

displays the measured temperature

The output lights are not used, and the lower (setpoint) display is disabled.

Power Output

Indicator

Scroll Key

Down Key

Up Key

Alarm

Indicator

Measured

Temperature

Remote

Indicator

(When configured)

Scroll Key

Page Key

Quick Start Guide

MC23-GB –v1.01

3 User levels

3.1 Understanding User Levels

There are two user levels in the controller; Level 1(Operator) and Level 2 (Supervisor).

Level 1 (Operator) is for the day to day operation of the controller. These parameters are

not protected by a security code.

Level 2 (Supervisor) provides access to additional parameters. Access to these is protected

by a security code

To Enter Level 2

1. Press and hold the page key for 3 seconds.

2. The display will show Leu 1 GOTO

3. Release the page Key

4. Press the Upor Down to choose LEu 2 (level 2)

5. Press the Up or Down to enter the code (Level 2 Code = 9).

If the correct code is entered, PASS should momentarily be displayed and then revert to the

level 2 home display (See Section Error! Reference source not found.)

If an incorrect code is entered the display reverts back to Level 1 home display (See Section

Error! Reference source not found.)

When level 2 operations have been completed, the supervisor must return to Level 1 either

manually or by ‘power cycling’, there is no time out function.

To Return to Level 1

1. Press and hold the page Key 

2. Press Down to select LEu 1

It is not necessary to enter a code when going from a higher level to a lower level

When level 1 is selected, the display reverts to the home display (See Section 2.1)

Table showing parameters accessible in level 1 and Level 2

Operator LEVEL 1

Supervisor LEVEL 2

Home display

Home Display

Alarms (if configured)

Comms (if configured)

Controller setup

TIP

If while navigating the controller a parameter has been passed or you need to access

parameters which would be at the end of a scroll list, press and hold Scroll and use Up 

to return to a previous parameter.

Basic Operation

MC23-GB –v1.01

4 Setting up the controller

Before using the controller (or during its lifetime) certain parameters may have to be set,

depending on specific requirements. To do this the controller must be set to supervisor level

(Level 2) see section 3.1

4.1 Customer ID.

A furnace or oven identification number can be entered if required. This maybe used to

identify one of many units, for production or quality control systems.

Press scroll until the display shows ID <customer ID>. Using the Up Down enter

your own identification number. This can range from 1-9999.

4.2 Units

Press scroll until the display shows units <Display Units>. Using the Up or Down

select the required units.

Mnemonic

Description

nonE

No units (Default °C)

°C

Celsius

°F

Fahrenheit

°K

Kelvin

PErc

4.3 Scrolling Text

If at any time the scrolling text is not required.

Press and hold the Page for three seconds until “GOTO”is displayed

Press Scroll until the display shows. TEXT <ENABLE/DISABLE SCROLLING TEXT>

Use the Up Down to select ON or OFF

Options

MC23-GB –v1.01

5 Digital Communications

5.1 Digital Communications –RS232

If the RS232 option is supplied, then the furnace is fitted with one subminiature D-socket

connected to the controller communications (comms) module. RS232 is suitable for direct

connection to a personal computer (PC), using a “straight through” cable as follows (the

linked pins at the computer end are recommended but may not be necessary). The cable is

usually 9-pin at the furnace end and 9-pin at the computer, but other alternatives are shown

in parentheses.

Furnace end of cable

RS232 Cable: furnace to PC

Computer end of cable

female 9-pin (25-pin)

9-pin (25-pin) male

3 (2)

2 (3)

Com

5 (7)

Com

7,8 (4,5)

Link

together

1,4,6 (6,8,20)

Link

together

5.2 Digital Communications –RS485

If an RS485 option is supplied, then the furnace is fitted with two sub-miniature D-sockets.

Connection between products is by “straight” cable as follows:

RS485 cable:

furnace to furnace

female 9-pin (25-pin)

9-pin (25-pin) female



3 (2)



2 (3)

Com

5 (7)

Com

If a boxed KD485 RS485 to RS232 converter is supplied, then the connection cable from

furnace to KD485 should be a “straight” cable, the same as the furnace-to-furnace cable.

The connection between the KD485 and the PC should be a “crossover” cable, the same as

the Furnace to PC cable in section 5.1.

5.3 Comms Address

Typically the comms address is set to 1, but this can be changed. In the case of RS485 and

multiple instruments it is necessary to set different addresses.

To change the address value access the level 2 list. In level 2 press the scroll key until

the ADDR (ADDRESS) parameter is displayed. Use the Up Down to select the address

value.

Basic Operation

MC23-GB –v1’01 01/01/16

Carbolite Gero, Parsons Lane, Hope,

Hope Valley, S33 6RB, England.

Telephone: +44 (0)1433 620011

Fax: +44 (0)1433 621198

E-mail: [email protected]

For preventive maintenance, repair and calibration

of all Furnace and Oven products, please contact:

Carbolite Gero Service

Telephone: +44 (0)1433 624242

Fax: +44 (0)1433 624243

Email: ServiceUK@carbolite-gero.com

6 Navigation Diagram

6.1 3216cc indicator

7 Controller Fault

7.1 Fault Code Diagnostic Table

Error Code

Explanation

Actions

S.br

Temperature sensor failure

Replace the Furnace or Oven

Temperature Sensor

Pass code = 9

LEVEL 1 ACCESS LEVEL 2

PV LEV PV

GOTO

ID TEXT ADDR

UNITS



3 Sec









Andere Handbücher für Invensys 3216

Inhaltsverzeichnis

Andere Eurotherm Temperaturregler Handbücher

Eurotherm

Eurotherm 2216e Betriebsanleitung

Eurotherm

Eurotherm 2108i Verdrahtungsschema

Eurotherm

Eurotherm 2408i Bedienungsanleitung

Eurotherm

Eurotherm 3116 Bedienungsanleitung

Eurotherm

Eurotherm 3200 Bedienungsanleitung

Eurotherm

Eurotherm 2208L Bedienungsanleitung

Eurotherm

Eurotherm 2116 Bedienungsanleitung

Eurotherm

Eurotherm 3116 PID Bedienungsanleitung

Eurotherm

Eurotherm Invensys 3216 Bedienungsanleitung

Eurotherm

Eurotherm 216 Bedienungsanleitung

Eurotherm

Eurotherm 2216e Betriebsanleitung

Eurotherm

Eurotherm 2208e Betriebsanleitung

Eurotherm

Eurotherm 2216L Verdrahtungsschema

Eurotherm

Eurotherm Invensys 3216 Bedienungsanleitung

Eurotherm

Eurotherm 3116 Bedienungsanleitung

Eurotherm

Eurotherm 3100 Installations- und Betriebshandbuch

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema