EVA Logik ZW12 Bedienungsanleitung

Z-Wave Mutil-relay

Federal Communications Commission (FCC) Statement

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may caus harmful interference to radio communications.However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.Increase the separation between the equipment and

receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment Z-Wave Mutil-relay

should be installed and operated with minimum distance 20cm between the radiator and your body.

IC Caution:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject

to the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired

operation of the device.

DECLARATION DE CONFORMITE D'INDUSTRIE CANADA

Ce périphérique a été testé et reconnu conforme aux limites spécifiées dans RSS-210.

Son utilisation est soumise aux deux conditions suivantes :

(1) il ne doit pas provoquer d'interférences gênantes et

(2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement.

WARRANTY

Evalogik Products warrants this product to be free from manufacturing defects for

a period of two years from the original date of consumer purchase. This warranty is limited

to the repair or replacement of this product only and does not extend to consequential or

incidental damage to other products that may be used with this product.

This warranty is in lieu of all other warranties, expressed or implied. Some states do not

allow limitations on how long an implied warranty lasts or permit the exclusion or limitation

of incidental or consequential damage, so the above limitations may not apply to you.

This warranty gives you specific rights, and you may also have other rights which vary from

state to state. if the unit should prove defective within the warranty period.

SPECIFICATIONS WARNING

Model:ZW12 RISK OF FIRE

Power: 120 VAC, 60 Hz. RISK OF ELECTRICAL SHOCK

Signal (Frequency): 908.42 MHZ. RISK OF BURNS

Maximum load for outlet 500W Resistive CONTROLLING APPLIANCES:

Maximum load for the Z-Wave™ controlled outlet: EXERCISE EXTREME CAUTION WHEN USING Z-Wave™ DEVICES TO CONTROL

APPLIANCES. OPERATION OF THE Z-Wave™ DEVICE MAY BE IN A DIFFERENT

Range: Up to 100 feet line of sight between the Wireless

Controller

ROOM THAN THE CONTROLLED APPLIANCE, ALSO ANUNINTENTIONAL ACTIVATION

and the closest Z-Wave™ receiver module. MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-Wave™ DEVICES

Operating Temperature Range: 32-104° F (0-40° C) MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED EVENT PROGRAMMING.

DEPENDING UPON THE APPLIANCE, THESE UNATTENDED OR UNINTENTIONAL

Specifications subject to change without notice OPERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE

due to continuing product improvement REASONS, WE RECOMMEND DO NOT RETURN THIS PRODUCT TO THE STORE

THE FOLLOWING:

Website:www.nie-tech.com DO NOT USE Z-Wave™ DEVICES TO CONTROL ELECTRIC

HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT

A HAZARDOUS CONDITION DUE TO UNATTENDED OR

UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.

Introduction:

This product can be operated in any Z-Wave network with other Z-Wave Plus™ certified devices from other manufacturers.

All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

Each module is designed to act as a repeater,which will re-transmit a radio frequency (RF) signal by routing the signal

around obstacles and radio dead spots to ensure that the signal is received at its intended destination.

ZW12 is a security enabled Z-Wave Plus™ device. A security Enabled Z-Wave Plus™ Controller must be used in order to fully utilize the product.

The Device Type of the ZW12 is on/off power switch.

The Role Type of the ZW12 is Always On Slave Role Type

Key

Features

---Remote ON/OFF control via the Z-Wave™ controller

---Manual ON/OFF control with the front panel push button

---Support Association Group and Auto Report switch status

---Support firmware upgrades via Over-the-air (need Gateways support)

---Support Scenes

Product Overview:

A. Push button

B. Status LED

C. POWER INPUT DC:5V

D. Connect the switch

E. Relay Output

Indicator Command Class ZW12 Installation Wiring Diagram

* The indicator (blue color) will flashes according the indicator set

command received from HUB.

Basic

command

class

* The basic set command class is mapping to binary switch set.

* Basic set will control both two endpoints' relay to turn on or turn off.

Key function description

Function 1: press and hold for more than 5s,change SW1 mode

Function 2: press 2x and hold for more than 5s,change SW2 mode

Function 3: quickly press 3x Button: ADD(inclusion) OR Remove( exclusion)

Function 4: press 5x change led parameter

Function 5: press 4x, then LED lit for 4s, within this time press 4x again – LED blinks 3 times then off to FACTORY RESET

(Node:Please use this procedure only when the network primary controller is missing or otherwise inoperable.)

Adding Your Device To A Hub

The device support two methods of inclusion,When using a Z-Wave Plus™ certified controller choose Network Wide Inclusion or SmartStart,

Network Wide Inclusion To A Z-Wave™ Network

1,Refer to your primary controller instructions to process the inclusion / exclusion setup procedure.

2,When prompted by your primary controller, click the Up or Down button three times in one second.

The device is compatible with SmartStart

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave™ QR Code found on the top of the outlet or the back of

the box with a controller providing SmartStart inclusion.No further action is required and the SmartStart product will be added automatically within

10 minutes of being switched on and in the network vicinity.

CODE

the QR code are sticked to the side of the case,DSK is included in the QR code.

DSK

The DSK code can be found on the DSK label which is attached on the packaging box.

Command Class

[ROOT ENDPOINT] ENDPOINT 1& ENDPOINT 2

Notification Type and events

[NOTES]:

1)For the root endpoint, the Notification and Sensor Binary only supported when the parameter 2 is set to 4~9 or the parameter 3 is set to 4~9.

(When one of input or both two inputs are used to sensor alarm.

2)For the endpoint 1, the Notification and Sensor Binary only supported when the parameter 2 is set to 4~9.

(When input (S1 and C) is used to sensor alarm.

3)For the endpoint 1, the Notification and Sensor Binary only supported when the parameter 3 is set to 4~9.

(When input (S2 and C) is used to sensor alarm.

Z-Wave™ Configuration Parameters

You may use the below configuration parameters to change settings of the corresponding functionality.

1: Restore state after power failure

Paramter No: 1(0x01) Size:1 Byte (default=1)

Value: 00 All relays automatically turn OFF once power is restored

Value: 01 All relays remember the status prior to power outage and turns back to it

Value: 02 All relays turned on after power failure

Value: 03 R1 recovered, R2 ON

Value: 04 R2 recovered, R1 – ON

2：Select switch one's type

Paramter No: 2(0x02) Size:1 Byte (default=2)

Value: 00 momentary switch

Value: 01 toggle switch (contact closed -ON, contact opened - OFF)

Value: 02 toggle switch (device changes status when switch changes status)

Value: 03 garage door mode(toggle switch type for external switch (like in value 1) + built-in 2 second auto-off timer

for Z-Wave control (so if user turns the relay on from the Z-Wave hub, it will automatically turn off after 2 seconds)

Value: 04 water alarm

Value: 05 heat alarm

Value: 06 Smoke alarm

Value: 07 Door alarm

Value: 08 CO alarm

Value: 09 CO2 alarm

* After changing the values of the parameter, first exclude the device (without setting the parameters to their default values),

wait at least 5 seconds and then re-include the device! While par=4 to 9.

3：Select switch two's type

Paramter No: 3(0x03) Size:1 Byte (default=2)

Value: 00 momentary switch

Value: 01 toggle switch (contact closed -ON, contact opened - OFF)

Value: 02 toggle switch (device changes status when switch changes status)

Value: 03 garage door mode(toggle switch type for external switch (like in value 1) + built-in 2 second auto-off timer

for Z-Wave control (so if user turns the relay on from the Z-Wave hub, it will automatically turn off after 2 seconds)

Value: 04 water alarm

Value: 05 heat alarm

Value: 06 Smoke alarm

Value: 07 Door alarm

Value: 08 CO alarm

Value: 09 CO2 alarm

After changing the values of the parameter, first exclude the device (without setting the parameters to their default values),

wait at least 5 seconds and then re-include the device! While par=4 to 9.

5: LED indicator

Paramter No: 5(0x05) Size:1 Byte (default=0)

Value: 00 led OFF when output ON,led ON when output OFF

Value: 01 led ON when output ON,led OFF when output OFF

Value: 02 led always OFF

Value: 03 led always ON

6：EP1 Auto Turn-off Timer(only switch-1 type < 4)

Paramter No: 6(0x06) Size:4 Byte (default=0)

Value: 00 timer disabled

Value: 1-65535 This Timer Turn-off

7：EP1 Auto Turn-on Timer(only switch-1 type < 4)

Paramter No: 7(0x07) Size:4 Byte (default=0)

Value: 00 timer disabled

Value: 1-65535 This Timer Turn-on

8：EP2 Auto Turn-off Timer(only switch-2 type < 4)

Paramter No: 8(0x08) Size:4 Byte (default=0)

Value: 00 timer disabled

Value: 1-65535 This Timer Turn-off

9：EP2 Auto Turn-on Timer(only switch-2 type < 4)

Paramter No: 9(0x09) Size:4 Byte (default=0)

Value: 00 timer disabled

Value: 1-65535 This Timer Turn-on

10：Input 1 trigerring(Input1 trigger the relay 1)

Paramter No: 10(0x0A) Size:1 Byte (default=1)

Value: 00 trigger disable (only notification to hub according to set par 2)

Value: 01 trigger unable (default);trigger the relay and hub notification

11：Input 2 trigerring(Input2 trigger the relay 2)

Paramter No: 11(0x0B) Size:1 Byte (default=1)

Value: 00 trigger disable (only notification to hub according to set par 2)

Value: 01 trigger unable (default);trigger the relay and hub notification

12：EP1 Manual Control

Paramter No: 12(0x0C) Size:1 Byte (default=1)

Value: 00 manual control disabled (no reports to the hub)

Value: 01 manual control enabled

Value: 02 manual control disabled (sends on/off reports to the hub)

13：EP2 Manual Control

Paramter No: 13(0x0D) Size:1 Byte (default=1)

Value: 00 manual control disabled (no reports to the hub)

Value: 01 manual control enabled

Value: 02 manual control disabled (sends on/off reports to the hub)

15：EP1 Auto Turn-Off Timer Unit

Paramter No: 15(0x0F) Size:1 Byte (default=0)

Value: 00 minutes

Value: 01 seconds

Value: 02 hours

16：EP1 Auto Turn-ON Timer Unit

Paramter No: 16(0x10) Size:1 Byte (default=0)

Value: 00 minutes

Value: 01 seconds

Value: 02 hours

17：EP2 Auto Turn-Off Timer Unit

Paramter No: 17(0x11) Size:1 Byte (default=0)

Value: 00 minutes

Value: 01 seconds

Value: 02 hours

18：EP2 Auto Turn-ON Timer Unit

Paramter No: 18(0x12) Size:1 Byte (default=0)

Value: 00 minutes

Value: 01 seconds

Value: 02 hours

24：Sw1,Sw2 setting

Paramter No: 24(0x18) Size:1 Byte (default=0)

Value: 00 Normal

Value: 01 Union (only switch type1 < 4 && switch type2 < 4)

IF both switches OFF - only one of them may be turned ON.

- turning sw1 ON : delayed 0.5 s, sw2 and R2 turned off first (immediately)

- turning sw2 ON - delayed 0.5s , sw1and R1 turned off first ( immediately )

The situation for DC motor control(SW1 control—right, SW2 control-left.

-main switch can turn ON and OFF only sw1

Support for Association Groups

ZW12 supports 3 association groups. Group 1 supports 1 node ID,Group 2 and Group 3 Supports maximum of 5 node ID’s

Association group_1:Z-Wave™ Plus Lifeline

Association group_1 is default to associate with the primary controller (Gateway/Hub/Controller) for ZW12 Status change report,

1. ZW12 will trigger AUTO report function if the Switch status had been changed.

(ex.Switch Binary Report/Indicator Report/ Notification Report/ Device Reset Locally Notification/Sensor Binary Report)

Association group_2:basic set command on/off controlt

When the output of the ZW12 is changed, On (0xFF) or Off (0x00). The ZW12 will automatically send out a related basic set

command. On (0xFF) or Off (0x00) to its associated group.

Association group_3:basic set command on/off controlt

When the output of the ZW12 is changed, On (0xFF) or Off (0x00). The ZW12 will automatically send out a related basic set

command. On (0xFF) or Off (0x00) to its associated group.

Restoring Factory Defaults

ZW12 is removed from the network and will be restored to the factory setting

All Configuration Parameters values and Association information will be restored to factory default settings and excluded from the network.

Manual Reset:press 4x, then LED lit for 4s, within this time press 4x again – LED blinks 3 times then off to FACTORY RESET

Remark : All the setting and data will be permanently deleted.

Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Andere EVA Logik Relais Handbücher

EVA Logik

EVA Logik ZW11 Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung