Event Lighting DARKSTAR Bedienungsanleitung

DARKSTAR

20 x 3W RGBW LED fat beams + 12 x 1W LED strobe effect light with IR remote & DMX

USER MANUAL

For safety, please read this user manual carefully before initial use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications within this

manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any

errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

www.event-lighting.com.au Ver 1.0

www.event-lighting.com.au

CONTENTS

Introduction, safety instructions, product Installation Page 2

Overview, dimensions, control board operation Page 3

Menu Map, IR remote operation Page 4

DMX chart Page 5 - 8

Technical specifications, warranty Page 8

www.event-lighting.com.au

Introduction

The DARKSTAR will blow you away with the versatile output available from this awesome new effect. With fat

multi-coloured beams firing out of 5 lenses and a blinding white strobe effect, the DARKSTAR brings a dynamic and

exciting atmosphere to any party or special event. The power on offer is incredible with a massive selection of 34 auto

and sound active shows, or run via DMX. Pro features are standard including “smart” fanless cooling and power in/out

connectors for easy cabling. A unique housing design and special optics produce wide beams similar to a moving head.

Add the strobe and chase effects and you have one very serious party effect.

Safety Instructions

WARNING

•Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.

•Do not look at the light source when the device is on.

•CAUTION: This unit's housing may be hot during and after operation.

•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.

•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.

•Use a safety chain when mounting this device overhead.

•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.

•Do not operate this device if the housing, lenses, or cables appear damaged.

•Do not connect this device to a dimmer or rheostat.

•ONLY connect this device to a grounded and protected circuit.

•ONLY use the hanging bracket to carry this device.

•In case of a serious operating problem, stop using immediately.

•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.

Power Input & Power Linking

This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.

Link up to the maximum 8A. DO NOT exceed this number.

Product Installation

This device can be mounted in many orientations provided each individual device is secured by the use of correct

mounting bracket.

Use a safety chain when mounting this device overhead.

Fuse Replacement

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au

Overview

Dimensions

Control Panel Operation

1. MENU button: select an operation mode or return to previous screen

2. UP button: move up the menu or select higher value

3. DOWN button: move down the menu or select lower value

4. ENTER button: change or activate menu options

5. DMX signal LED indicator: This LED will flash when the DMX is

connected.

6. Master / Slave mode indicator: This LED will flash when the machine

is in slave mode.

The LED display will switch off after ten seconds. Press any button to turn the display on.

When the Orbit is connected via DMX or SLAVE signal, it automatically activates DMX or SLAVE mode. If you

disconnect the DMX or SLAVE signal, it will return to the previous setting.

www.event-lighting.com.au

Menu Map

Press the MENU button to select an operation mode or return to previous menu. Use UP and DOWN button to navigate

the menu. Press the ENTER button to change or activate menu options.

Select DMX address

Select DMX channel mode (2 / 4 / 8)

Select auto run program (18 auto run programs)

Select auto run program speed

Select sound active program (16 sound active programs)

Select mic sound sensitivity level

IR Remote Control Operation

1. Auto: The fixture will select autorun 0 by default. Use +/- to adjust the program speed.

There are 8 speed levels that can be selected via the remote. Autorun programs 1 to

10 can be selected via the remote by entering digits.

(Note: Autorun program 10 is selected by digit “0”)

2. Sound: The fixture will select the last used sound active program setting by default.

Select the next sound active program in the sequence by pressing “Sound”again. You

can also use +/- to select different sound active programs. Sound active programs 0 to

9 can be selected via the remote by entering digits.

3. DMX: Select a DMX address by holding the button for 2 seconds, followed by entering

the 3-digit DMX address. The fixture must not be connected to a DMX input signal

when entering the address.

4. Black Out

5. Red: Switch on red LED

6. Green: Switch on green LED

7. Blue: Switch on blue LED

8. White: Switch on white LED

9. Jump: Select the next program in the autorun program sequence，from 0 to 16, by pressing “Jump”.

10. Fade: Select autorun program 17 (includes fade effects) by pressing “Fade”. Select autorun program 18

(includes fade effects) by pressing “Fade”again. To return to program 17, press “Fade”again.

11. Color: Select red, green, blue, white

12. Flash: Select strobe functions when the fixture is in autorun or colour modes. When in autorun mode, press

“Flash”to activate the 12 strobe LED’s. Adjust the speed with +/-, there are 8 speed levels that can be selected

via the remote. When in colour mode, press “Flash”to strobe/flash the 5 fat beam LED’s, the strobe LED’s will

remain off. Adjust the speed with +/-, there are 8 speed levels that can be selected via the remote.

www.event-lighting.com.au

DMX Chart

2 Channels Mode

Ch1

Ch2

Value

Function

Value

Function

000-010

No function

011-015

Sound active mode 0 (The fixture will cycle through programs 1-16, running

each program through 1 cycle then moving to the next program.)

000 - 255

Mic sensitivity

adjustment

016-022

Sound active mode 1

023-029

Sound active mode 2

030-036

Sound active mode 3

037-043

Sound active mode 4

044-050

Sound active mode 5

051-057

Sound active mode 6

058-064

Sound active mode 7

065-071

Sound active mode 8

072-078

Sound active mode 9

079-085

Sound active mode 10

086-092

Sound active mode 11

093-099

Sound active mode 12

100-106

Sound active mode 13

107-113

Sound active mode 14

114-120

Sound active mode 15

121-127

Sound active mode 16

128-147

Auto run mode 0 (The fixture will cycle through programs 1-18, running

each program through 1 cycle then moving to the next program.)

000 - 255

Auto run speed

adjustment

148-153

Auto run mode 1

154-159

Auto run mode 2

160-165

Auto run mode 3

166-171

Auto run mode 4

172-177

Auto run mode 5

178-183

Auto run mode 6

184-189

Auto run mode 7

190-195

Auto run mode 8

196-201

Auto run mode 9

202-207

Auto run mode 10

208-213

Auto run mode 11

214-219

Auto run mode 12

220-225

Auto run mode 13

226-231

Auto run mode 14

232-237

Auto run mode 15

238-243

Auto run mode 16

244-249

Auto run mode 17

250-255

Auto run mode 18

www.event-lighting.com.au

4 Channels Mode

Chanel

Function

Value

Detail Function

Ch 1

Master dimmer

000 - 255

Master dimmer for all LED from 0% to 100%

Ch 2

Strobe selection effect

000 - 010

Black out

011 - 249

Strobe ( slow to fast 1 - 20Hz )

250 - 255

Strobe off

Ch 3

Beam selection colour

effect setting

000 - 015

No function

016 - 031

Red

032 - 047

Green

048 - 063

Blue

064 - 079

White

080 - 095

Red / Green

096 - 111

Red / Blue

112 - 127

Red / White

128 - 142

Green / Blue

143 - 159

Green / White

160 - 174

Blue / White

175 - 255

Adjust automatic colour change ( slow - fast )

Ch 4

Beam selection strobe

effect setting

000 - 005

Strobe off

006 - 010

Black out

011 - 249

Strobe ( slow to fast 1 - 20Hz )

250 - 255

Strobe off

8Channels Mode

Chanel

Function

Value

Detail Function

Ch 1

Master dimmer

000 - 255

Master dimmer for all LED from 0% to 100%

Ch 2

Strobe selection effect

000 - 010

Black out

011 - 249

Strobe ( slow - fast 1 - 20Hz)

250 - 255

Strobe off

Ch 3

1st beam selection

colour effect setting

000 - 015

No function

016 - 031

Red

032 - 047

Green

048 - 063

Blue

064 - 079

White

080 - 095

Red / Green

096 - 111

Red / Blue

112 - 127

Red / White

128 - 142

Green / Blue

143 - 159

Green / White

160 - 174

Blue / White

175 - 255

Adjust automatic colour change ( slow - fast )

www.event-lighting.com.au

Ch 4

2nd beam selection

colour effect setting

000 - 015

No function

016 - 031

Red

032 - 047

Green

048 - 063

Blue

064 - 079

White

080 - 095

Red / Green

096 - 111

Red / Blue

112 - 127

Red / White

128 - 142

Green / Blue

143 - 159

Green / White

160 - 174

Blue / White

175 - 255

Adjust automatic colour change ( slow - fast )

Ch 5

3rd beam selection

colour effect setting

000 - 015

No function

016 - 031

Red

032 - 047

Green

048 - 063

Blue

064 - 079

White

080 - 095

Red / Green

096 - 111

Red / Blue

112 - 127

Red / White

128 - 142

Green / Blue

143 - 159

Green / White

160 - 174

Blue / White

175 - 255

Adjust automatic colour change ( slow - fast )

Ch 6

4th beam selection

colour effect setting

000 - 015

No function

016 - 031

Red

032 - 047

Green

048 - 063

Blue

064 - 079

White

080 - 095

Red / Green

096 - 111

Red / Blue

112 - 127

Red / White

128 - 142

Green / Blue

143 - 159

Green / White

160 - 174

Blue / White

175 - 255

Adjust automatic colour change ( slow - fast )

Ch 7

5th beam selection

colour effect setting

000 - 015

No function

016 - 031

Red

032 - 047

Green

048 - 063

Blue

064 - 079

White

080 - 095

Red / Green

096 - 111

Red / Blue

112 - 127

Red / White

www.event-lighting.com.au

128 - 142

Green / Blue

143 - 159

Green / White

160 - 174

Blue / White

175 - 255

Adjust automatic colour change ( slow - fast )

Ch 8

Beam selection strobe

effect setting

000 - 005

Strobe off

006 - 010

Black out

011 - 249

Strobe ( slow to fast 1 - 20Hz )

250 - 255

Strobe off

TECHNICAL SPECIFICATIONS

-Power supply: 100~240 V AC, 50/60 Hz

-Power consumption:75 W

-Light Source:

20pcs 3W LED for fat beams effect (5pcs red, 5pcs green, 5pcs blue and 5pcs white)

12pcs 1W white LED for strobe effect

-Power Connection: IEC power input and output connection

-LED Life: 50,000 hours

-Coverage Angle: 80 degree

-Control: DMX512 3-pin XLR interfaces, 2/4/8 channel mode, IR remote control

-4-button LED display control panel

-Power linking: 15 units at 240V AC

-Smart cooling system without fan

-Operation modes: DMX, 18 sets of auto show, 16 sets of sound active show, master/slave mode, IR remote

control

-Fuse: `F2A 250V

-Net weight: 4.6kg

-Overall size: 295 x 312 x 313 mm

WARRANTY

Please refer to your local dealer or please contact Event Lighting Pty Ltd

Website: www.event-lighting.com.au.

Inhaltsverzeichnis

Andere Event Lighting DJ-Equipment Handbücher

Event Lighting

Event Lighting Fresnel Bedienungsanleitung

Event Lighting

Event Lighting BLINDER Series Bedienungsanleitung

Event Lighting

Event Lighting PARP12x8 Bedienungsanleitung

Event Lighting

Event Lighting M1S80W Bedienungsanleitung

Event Lighting

Event Lighting Fresnel Bedienungsanleitung

Event Lighting

Event Lighting M7W15RGBW Bedienungsanleitung

Event Lighting

Event Lighting M1S190W Bedienungsanleitung

Event Lighting

Event Lighting DERBY3 Bedienungsanleitung

Event Lighting

Event Lighting CO2RGB Bedienungsanleitung

Event Lighting

Event Lighting LM7X12W Bedienungsanleitung

Event Lighting

Event Lighting PRO PAR PAR12X8L Bedienungsanleitung

Event Lighting

Event Lighting LM6X15 Bedienungsanleitung

Event Lighting

Event Lighting M1S75W Bedienungsanleitung

Event Lighting

Event Lighting PAR19X12L Bedienungsanleitung

Event Lighting

Event Lighting DASDI1000RGB Bedienungsanleitung

Event Lighting

Event Lighting M7W40RGBW Bedienungsanleitung

Event Lighting

Event Lighting F100WWMZ Bedienungsanleitung

Event Lighting

Event Lighting STROBEXRGB Bedienungsanleitung

Event Lighting

Event Lighting KONTROL36 Bedienungsanleitung

Event Lighting

Event Lighting PS300IICW Bedienungsanleitung

Event Lighting

Event Lighting M1B60W Bedienungsanleitung

Event Lighting

Event Lighting StrobeX Bedienungsanleitung

Event Lighting

Event Lighting DGS400RGB Bedienungsanleitung

Event Lighting

Event Lighting PIXBAR12x3 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung