Event Lighting SURF640 Bedienungsanleitung

www.event-lighting.com.au

SURF640

6X40W TILT BAR WITH ZOOM

USER MANUAL

For safety, please read this user manual carefully before initial use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications

within this manual are subject to change without notice. Event Lighting assumes no liability or

responsibility for any errors or omissions. Please consult Event Lighting for any clarification or

information regarding this item.

Version: 3.0 (06 May 2020)

www.event-lighting.com.au

Safety Instructions

Warning

•Do not open this device, there are no user-serviceable parts inside. Risk of electric

shock.

•Do not look at the light source when the device is on.

Caution: This unit's housing may be hot during and after operation.

•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from

adjacent surfaces.

•Do not leave any flammable material within 50 cm of this unit while operating or

connected to power.

•Use a safety chain when mounting this device overhead.

•Do not operate this device outdoors or in any location where dust, excessive heat, water,

or humidity may affect it.

•Do not operate this device if the housing, lenses, or cables appear damaged.

•Do not connect this device to a dimmer or rheostat.

•ONLY connect this device to a grounded and protected circuit.

•ONLY use the hanging bracket to carry this device.

•In case of a serious operating problem, stop using immediately.

•The maximum ambient temperature is 104° F (40° C). Do not operate this device at

higher temperatures.

Power Input & Power Linking

This device has an auto-switching power supply work with input voltage range of 100~240 VAC,

50/60 Hz.

Link up to the maximum 8A. DO NOT exceed this.

Fuse Replacement

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing

(anticlockwise).

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au

Product Installation

•This device can be mounted in many orientations provided each individual device is

secured by the use of correct mounting bracket.

•Use a safety chain when mounting this device overhead.

www.event-lighting.com.au

Dimensions

Lux Chart

Lux @ 4°

Distance (m)

Diameter (m)

Ø 0.06

Ø 0.2

Ø 0.33

Ø 0.55

Ø 0.68

11,200

2,450

1,670

790

595

16,700

5,300

2,550

1,210

905

7,200

2,160

1,070

550

360

23,000

7,350

3,550

1,735

1,300

Full

46,000

13,900

8,450

3,980

2,500

www.event-lighting.com.au

Lux @ 38°

Distance (m)

Diameter (m)

Ø 0.7

Ø 2.2

Ø 2.5

Ø 5.6

Ø 6.8

2,110

302

114

3,180

459

175

1,310

180

4,580

646

244

105

Full

9,200

1,268

480

210

148

Menu Operation

Menu – Move up a level.

Up – Move selection up one item.

Down – Move selection down one item.

Enter – Select / Move down a level

DESCRIPTION

Function Mode

DMX Address

A001-AXXX

DMX Address setting

DMX Channels

8 CH

8 channel mode

16 CH

16 channel mode

46 CH

46 channel mode

Manual

Preset

Manual mode setting. Straw,

WarmW, White, CoolW, Blue,

Magent, Red, Orange, Yellow,

Green, Teal, Cyan, Blue

Finetune

Finetune the preset (++/--)

Dimmer

0-100

Auto Program

Program 1..8

Wait

Time between 2 colours. 0.1s-

20min

Fade

Fade time between 2 colours. 0.1s-

60s

Dimmer

0-100

Movement

Tilt (0-255)

Tilt between 0°-220°, applied to

Manual & Auto Program

Zoom (0-255)

Zoom between 3.5°-38°, applied to

Manual & Auto Program

Options

Master/Slave

Off, Master, Slave:1-12

Setting

Lost DMX

Hold/blackout when DMX lost

Tilt Reverse

Reverse tilt (on/off)

Zoom Reverse

Reverse zoom (on/off)

www.event-lighting.com.au

Pixel Reverse

Reverse pixel DMX addressing

(on/off)

LCD Reverse

Reverse LCD (on/off). Can also be

changed by pressing the UP and

DOWN buttons simultaneously.

Pixel Frequen

Pixel refresh rate. 1.2K, 2.4K, 3.6K,

4.8K, 6K, 7.2K, 8.4K, 9.6K, 10.8K,

12K, 13.2K, 14,4K, 15.6K, 16.8K,

18K, 19.2K, 20.4K, 21.6K, 22.8K,

24K.

Fan Speed

Auto/Low/High

KeyLock

Enable/Disable keylock. In the

locked state, keys will automatically

lock after 15s of inactivity. Press

and hold MENU for 2s to unlock.

When unlocked, the keys will not

automatically lock

Calibrat

Tilt Movement

If two fixtures are placed on the

same horizontal line and the emitted

light is not on the same horizontal

line, change this value to adjust the

tilt movement.

Zoom Movement

If the angle of the beams emitted by

two fixtures is not the same, change

this value to adjust the beam angle.

LEDs

If the colour temperature of one of

the six LEDs is inconsistent with the

others, change this value to adjust

the colour temperature.

Reset

Reset (no/yes)

Reset to factory settings.

Update

Update (no/yes)

Perform software update.

Info

Temperature

Temperature XX C

Temperature of the LEDs PCB.

The device is controlled by universal DMX 512 protocol, DMX address is the start channel used

to receive instructions from the external controller. For independent control, each fixture must be

assigned its unique address control channels. For example, this device has three channel

modes: 8/16/46, if we set the mode to standard 8 channels mode, and there are several models

that need to be independently controlled, we just simply address first fixture at 1, and second

fixture at 9, third one at 17, etc.

•If the devices have the same address, they will behave synchronically.

•Display is flashing when no DMX signal is received.

8 Channel Mode

Channel

Value

Function

www.event-lighting.com.au

0-255

Red

0-255

Green

0-255

Blue

0-255

White

0-255

Brightness

0-7

Shutter Closed (No Light)

Aug-15

No function (Shutter On)

16-119

Strobe effect Slow to Fast

120-127

No function (Shutter On)

128-183

Strobe Random Slow to Fast (All pixels)

184-191

No function (Shutter On)

192-247

Strobe Random Slow to Fast (Random pixels)

248-255

No function (Shutter On)

0-255

Tilt

0-255

Zoom

16 Channel Mode

Channel

Value

Function

0-255

Tilt Coarse

0-255

Tilt Fine

0-7

Shutter Closed (No Light)

8-15

No function (Shutter On)

16-119

Strobe effect Slow to Fast

120-127

No function (Shutter On)

128-183

Strobe Random Slow to Fast (All pixels)

184-191

No function (Shutter On)

192-247

Strobe Random Slow to Fast (Random pixels)

248-255

No function (Shutter On)

0-255

Max Intensity

0-255

CTC (Warm white to cold white)

0-255

Zoom

0-31

Dimmer Curve 1

32-63

Dimmer Curve 2

64-95

Dimmer Curve 3

96-127

Reserved

128-159

Reserved

160-191

Reserved

192-223

Reserved

224-255

Reserved

0-255

Tilt Speed Fast to Slow

0-15

No Function

16-95

Blackout by Movement Up and Down

96-175

Blackout by Movement Up

176-255

Blackout by Movement Down

0-85

Fan Speed (Auto)

www.event-lighting.com.au

86-171

Fan Speed (Low)

172-255

Fan Speed (High)

0-255

Red

0-255

Green

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

46 Channel Mode

Channel

Value

Function

Applies To

Normal

Reverse

0-255

Tilt Coarse

Whole Fixture

0-255

Tilt Fine

0-7

Shutter Closed (No Light)

8-15

No function (Shutter On)

16-119

Strobe effect Slow to Fast

120-127

No function (Shutter On)

128-183

Strobe Random Slow to Fast (All pixels)

184-191

No function (Shutter On)

192-247

Strobe Random Slow to Fast (Random

pixels)

248-255

No function (Shutter On)

0-255

Max Intensity

0-255

CTC (Warm white to cold white)

0-255

Zoom

0-31

Dimmer Curve 1

32-63

Dimmer Curve 2

64-95

Dimmer Curve 3

96-127

Reserved

128-159

Reserved

160-191

Reserved

192-223

Reserved

224-255

Reserved

0-255

Tilt Speed Fast to Slow

0-15

No Function

16-95

Blackout by Movement Up and Down

96-175

Blackout by Movement Up

176-255

Blackout by Movement Down

0-85

Fan Speed (Auto)

86-171

Fan Speed (Low)

172-255

Fan Speed (High)

0-255

Red

Pixel 1 Pixel 6

0-255

Green

www.event-lighting.com.au

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

0-255

Red

Pixel 2 Pixel 5

0-255

Green

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

0-255

Red

Pixel 3 Pixel 4

0-255

Green

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

0-255

Red

Pixel 4 Pixel 3

0-255

Green

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

0-255

Red

Pixel 5 Pixel 2

0-255

Green

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

0-255

Red

Pixel 6 Pixel 1

0-255

Green

0-255

Blue

0-255

White

0-255

Dim Coarse

0-255

Dim Fine

www.event-lighting.com.au

More Functions

•Remote Device Management (RDM) which allows users to remotely control the device.

Users can use RDM to remotely change the DMX address and the DMX settings. Each

device has a unique RDM code programmed during manufacture to facilitate this

function. It is not recommended for users to change this code.

•Software upgrade function via DMX cable. If there is any new firmware for this device, it

can be upgraded simply via a software upgrade box, without the need to change any

mechanical parts. The upgrade box is not included in the package, if you need any

further assistance please contact your authorized dealer.

•Software upgrade can also be performed by connecting to another fixture by following

these steps. This will update the software on Fixture A:

oOn Fixture A, go to Menu > Update > Y > Start.

oConnect Fixture A to Fixture B with a DMX cable.

oPower on Fixture B.

oWhen the LCD displays “Waiting for file”, press Enter on Fixture A.

oUpgrade will be complete. Press Menu to return to the Main Menu.

•Hibernation. The device will enter sleep mode if activated after a period of disconnecting

DMX signal to save power and will wake immediately when the DMX signal is sent or

received again.

Technical Specifications

Power

•Input Voltages: 100V~240V AC, 50/60Hz

•Power Consumption: 300W

•Power Connection: Neutrik Powercon TRUE1 in/out

•Power Linking: 2 units at 110V, 6 units at 240V

•Fuse: T6.3A, 250V

Photometrics

•Light Source: 6 pcs 40W RGBW LEDs

•Beam Angle: 4° to 38°

•Field Angle 10° to 42°

•Output: 1,268 lux @ 3m @ 38°

•PWM: 1,200 - 24,000 Hz

Effects

•Dimming: 0-100%

•Strobe: 1.2 - 24 Hz

Control

•Operational Modes: DMX512, Master / Slave, Sound Active, Manual

•RDM: Change DMX mode, change DMX address.

•Display: Reversible LCD Display

•DMX Protocol: DMX512

•DMX Channel Mode: 8 / 16 / 46 (Normal) / 46 (Reverse)

Inhaltsverzeichnis

Andere Event Lighting DJ-Equipment Handbücher

Event Lighting

Event Lighting M1S180W Bedienungsanleitung

Event Lighting

Event Lighting M1B60W Bedienungsanleitung

Event Lighting

Event Lighting M7W15RGBW Bedienungsanleitung

Event Lighting

Event Lighting PAR12x8A Bedienungsanleitung

Event Lighting

Event Lighting PIXBAR12x12 Bedienungsanleitung

Event Lighting

Event Lighting PRO PAR PAR12X8L Bedienungsanleitung

Event Lighting

Event Lighting M1S80W Bedienungsanleitung

Event Lighting

Event Lighting M6B20W Bedienungsanleitung

Event Lighting

Event Lighting CO2RGB Bedienungsanleitung

Event Lighting

Event Lighting PARRGBW12x8 Bedienungsanleitung

Event Lighting

Event Lighting M1H200W Bedienungsanleitung

Event Lighting

Event Lighting PS200LECW Bedienungsanleitung

Event Lighting

Event Lighting StrobeX Bedienungsanleitung

Event Lighting

Event Lighting SToRM Bedienungsanleitung

Event Lighting

Event Lighting BM1S50W Bedienungsanleitung

Event Lighting

Event Lighting Fresnel Bedienungsanleitung

Event Lighting

Event Lighting KONTROL36 Bedienungsanleitung

Event Lighting

Event Lighting PANBEAM4x4x10 Bedienungsanleitung

Event Lighting

Event Lighting PIXBAR6x12 Bedienungsanleitung

Event Lighting

Event Lighting DERBY3 Bedienungsanleitung

Event Lighting

Event Lighting M19W15RGBW Bedienungsanleitung

Event Lighting

Event Lighting DGS400RGB Bedienungsanleitung

Event Lighting

Event Lighting NITROBALL2 Bedienungsanleitung

Event Lighting

Event Lighting BLINDER Series Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung