Evil OMEN 2.0 Bedienungsanleitung

Paintball Marker Operator’s Manual

Version 2.0

Omen Manual 2.0 6/21/05 9:56 AM Page 1

Omen Manual 2.0 6/21/05 9:56 AM Page 2

EVIL OMEN™2.0 OPERATOR’S MANUA L

The EVIL OMEN™is a semi-automatic paintball marker designed to shoot

.68 caliber paintballs for use in the sport of paintball.

Paintball is a recreational and competitive sport played worldwide.Special

equipment used in paintball includes goggles designed for paintball,

paintball markers, and paintballs,which are liquid-filled gelatin capsules

that mark with a bright color. The object of the game is to capture the

opposing team’s flag; while on that quest, players try to mark their

opponents to eliminate them from the game.

PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY DESIGNED FOR

PAINTBALL MUST BEWORN BY ALL PERSONS WITHIN RANGE WHEN A

PAINTBALL MARKER IS IN USE. PA I N T BALL SAFETY RULES MUST BE

FOLLOWED AT ALL TIMES.

THE EVIL O M E N ™PAINTBALL MARKER IS NOT ATOY. MISUSE MAY CAUSE

SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBA L L

USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ

THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOA D I N G,PRESSURIZING,

OR OPERATING THE OMEN™PA I N T BALL MARKER.

STATEMENT OF LIABILITY

This EVIL OMEN™semi-automatic paintball marker is surrendered by

Pursuit Marketing, Inc. (PMI, Inc.), with the express understanding that the

purchaser assumes all liability arising out of any unsafe handling of this

marker or any action that violates any applicable laws or regulations. PMI,

Inc., assumes no liability for,and shall not be responsible for,any personal

injury or loss of property or life resulting from the use of this paintball

marker under any circumstances,including but not limited to those

resulting from intentional, reckless,negligent or accidental discharges.

READ THIS OPERATOR’S MANUAL COMPLETELY BEFORE LOADING,

PRESSURIZING,OR OPERATING THIS,OR ANY PAINTBALL MARKER.

EVIL®,OMEN™,and EVIL OMEN™is a registered trademark of

Pursuit Marketing, Inc. U.S. and Foreign Patents Pending.

Pursuit Marke ting, Inc. (PMI , Inc. ), founded in 1982 and manufacturer of

the EVIL OM EN™, Pure Energy Air Systems and the entire EVIL line of

markers, is an industry-leading manufacturer and wholesale distributor

with warehouses in key locations throughout the U. S.A. He adqu arters:

PMI, Inc., 55 Howard Ave, Des Plaines, Illinois 60018 USA; ph one

1.800.334. 0502 ; www.evil- pain tball.c om

WARNING

TABLE OF CONTENTS

PAINTBALL SAFETY RULES . . . . . . . . . . . . . . . . . .6

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . .8

COMPRESSED GAS/NITROGEN/CO2. . . . . . . . . .10

VELOCITY ADJUSTMENT . . . . . . . . . . . . . . . . . . .12

S P E C I F I C AT I O N S . . . . . . . . . . . . . . . . . . . . . . . . .1 3

WARRANTY INFORMATION CARD . . . . . . . .CENTER

PARTS/DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . .1 9

CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 5

TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

TROUBLESHOOTING & MAINTENANCE . . . . . . .2 8

THIS PAINTBALL MARKER IS INTENDED FOR SALE TO ADULTS ONLY, FOR USE IN COMPLIANCE WITH ALL

APPLICABLE LAWS AND REGULATIONS.ADULT SUPERVISION IS RECOMMENDED AT ALL TIMES WHENEVER A

MINOR IS HANDLING THIS PAINTBALL MARKER. PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY

DESIGNED FOR PAINTBALL MUST BE WORN BY ALL PERSONS WITHIN RANGE WHEN A PAINTBALL MARKER

IS IN USE. PAINTBALL SAFETY RULES MUST BE FOLLOWED AT ALL TIMES.

PAINTBALL MARKERS ARE NOT TOYS. MISUSE MAY CAUSE S E R I O U S INJURY OR DEATH. EYE PROTECTION

DESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ THIS

OPERATOR’S MANUAL COMPLETELY BEFORE LOADING,PRESSURIZING,OR OPERATING THE EVIL OMEN™

PAINTBALL MARKER.

Pursuit Marketing, Inc. (PMI, Inc.) reserves the right to modify or change its markers without

incurring any obligation to incorporate such modifications or changes in any of its products that

were sold prior to the modification. The information in this operator’s manual may be updated or

changed without notice.

This operator’s manual is intended to remain with the paintball marker upon any subsequent

transfer of the marker, whether through sale, resale, or furnishing in any manner.Updated and

replacement operator’s manual may be obtained from: Pursuit Marketing, Inc., 55 Howard Ave,

Des Plaines,IL 60018 USA; phone 1.800.579.1633; www.evil-paintball.com. Questions about the

operation of this or any EVIL™line of paintball markers can be directed to Pursuit Marketing Inc.,

or visit www.evil-paintball.com for updates regarding your OMEN™purchase.

WARNING

Omen Manual 2.0 6/21/05 9:56 AM Page 4

Markers with regulators hold pressure even after tank is removed. Shoot marker in a safe

direction after tank is removed to de-gas it completely.

This paintball marker operates using compressed gas or air at specified pressure ranges. Fol low

safety procedures when handling compressed gas or air. All filling of compressed gas or air

cylinders must be done by qualified persons.

Always cock marker before attaching air or gas source to it. Failure to always cock marker

before attaching air to it may cause accidental firing or discharge of paintballs.

Follow the rules of safe marker handling: Keep finger off trigger until ready to shoot. Keep

muzzle pointed in a safe direction. In addition, firmly insert a barrel plug or barrel bag onto

the muzzle and turn marker off when not in use and when in any non-shooting area.

Paintball markers with electronic frames have extremely sensitive triggers. Take extra safety

precautions anytime handling or shooting an electronic paintball marker. To avoid accidentally

firing the marker, keep the marker off until you are ready to fire.

Never shoot at domestic animals or wildlife.

Never mark objects outside the confines of the game or authorized shooting areas.

Never look down the barrel of the marker.

Never aim or shoot a paintball marker (loaded or unloaded) toward any person who is not

wearing protective goggles and headgear specifically designed for paintball.

Before disassembly,storage,or transport of the marker, remove all paintballs from the marker,

barrel, and loader; remove air source; and remove all gas or air from the marker. Insert barrel

plug and turn marker off.

Carry marker in case or sturdy bag when in public.

Safely and securely store marker to prevent access to it by unauthorized persons.

PAINTBALL MARKERS ARE NOT TOYS. MISUSE MAY CAUSE SERIOUS INJURY

OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE MUST BE WORN

BY THE USER AND ANY PERSON WITHIN RANGE. READ THIS OPERATOR’S MANUAL

COMPLETELY BEFORE LOADING,PRESSURIZING,OR OPERATING THE EVIL OMEN™

PAINTBALL MARKER.

Always wear protective goggles and headgear specifically designed for paintball when

shooting this or any paintball marker.

Every person within range of an area where a paintball marker is in use must wear

protective goggles and headgear specifically designed for paintball.

Operate a paintball marker only in areas where it is safe and lawful to do so.

Misuse of this paintball marker can result in criminal penalties,including jail time.

This marker is intended for sale to adults 18 years of age or older only.Adult supervision

is recommended at all times whenever a minor is handling this marker in any manner.

During game play,follow referee’s instructions and all field safety rules.Avoid shooting at

a player’s head, neck, or groin area.

Play paintball only where the rules of safe paintball play are followed.

All paintball markers must be chronographed regularly.Adjust marker to shoot paintballs

at a velocity less than 300 feet per second (fps) and/or that does not exceed the velocity

limit set by the paintball park where the marker is in use. Chronograph the marker at

regular intervals during the day, as well as any time the air source is refilled or changed,

any time the barrel is changed, and upon request of any player or game official.

There is always a chance that a paintball is lodged in the barrel of the marker even when it

is not visible in the chamber. To check if the marker is unloaded: remove air system and

shoot marker in a safe direction. Remove hopper, visually inspect chamber for a paintball,

remove and inspect barrel for the presence of a paintball. Never look down the barrel of any

paintball marker once the barrel is screwed into the marke r.

SAFETY FIRST!

WARNING

PAINTBALL BASIC SAFETY RULES PAINTBALL BASIC SAFETY RULES

Safety standards information is available from the American Society for Testing and

Materials,100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; phone

1.610.832.9500; www.astm.org. “Standard Practice for Paintball Field Operation” is

publication F1777-97, and “Standard Specification for Eye Protective Devices for

Paintball Sports” is publication F1776-97; inquire about additional publications which

may be available at the time request is made.

Omen Manual 2.0 6/21/05 9:56 AM Page 6

NEVER DISASSEMBLE MARKER UNTIL REMOVING ALL GAS OR AIR FROM THE

MARKER. RULES FOR SAFE HANDLING OF COMPRESSED GAS OR AIR MUST BE

FOLLOWED AT ALL TIMES.

FIRST TIME USERS FOLLOW INSTRUCTIONS CAREFULLY UNTIL FAMILIAR WITH MARKER

1. Attach threaded barrel firmly to marker.

2. Employ barrel blocking device (barrel condom, bag, sock or plug) firmly into or onto barrel.

3. Pull the cocking rod straight back from the rear of the marker until

the cocking mechanism locks back in the cocked position. Figures 1

and 2.

4. Turn marker “on.”

5. Squeeze the trigger with an even pressure. The cocking knob will

snap forward into the uncocked position.

6. Attach empty loader into feed tube.Use provided O-rings to make

the hopper snug.

7. Always cock the marker before attaching air.

8. Before attaching air source,read and understand the section in this

manual on “Compressed Gas/Air” (page 10/11). Follow safety rules

for handling compressed gas/air.If any leak occurs in the air system

or marker refer to troubleshooting guide or to a qualified airsmith. Use only cylinders for

compressed gas or air that comply with all applicable laws and regulations,including but

not limited to those of the U.S. Department of Transportation, OSHA, Compressed Gas

Association, and/or American Society for Testing and Materials.

Figure 1. Pull Back

Figure 2. Fully Cocked

EVERY PERSON WITHIN RANGE OF AN AREA WHERE ANY PAINTBALL MARKER IS IN

USE MUST WEAR PROTECTIVE GOGGLES AND HEADGEAR SPECIFICALLY DESIGNED

FOR PAINTBALL.

WARNING

9. Test for function after attaching air source by squeezing the trigger. The marker should

shoot air and the cocking knob should cycle forward and back, stopping in the cocked

position, after each trigger squeeze.Repeat several times.If the marker does not recock

itself, see page 29. Your Omen is NOT broken. It just needs the recock increased slightly.

10.Turn marker “off” and install barrel blocking device. Paintballs may then be loaded.

o p e r ating the evil omen™m a r k e r o p e r ating the evil omen™m a r k e r

WARNING

WHEN COCKING THE PRESSURIZED MARKER, DO NOT RELEASE THE COCKING

ROD UNTIL AFTER THE COCKING MECHANISM HAS LOCKED BACK INTO THE

COCKED POSITION; RELEASING THE COCKING ROD DURING COCKING CAN

CAUSE THE MARKER TO SHOOT.

WARNING

BEFORE DISASSEMBLY, STORAGE, OR TRANSPORT OF THE MARKER, REMOVE AIR

SOURCE FIRST.THEN REMOVE ALL PAINTBALLS FROM THE MARKER, BARREL, AND

LOADER. REMOVE ALL GAS OR AIR FROM THE MARKER BY CYCLING MARKER AFTER

TANK IS REMOVED. THE REGULATOR WILL HOLD A SHOT EVEN AFTER THE TANK IS

REMOVED UNLESS THE MARKER IS FIRED.INSERT BARREL BLOCKING DEVICE AND

SLIDE THE ON/OFF SWITCH TO THE “OFF” POSITION.

On/Off

Switch

DO NOT LEAVE MARKER IN DIRECT SUNLIGHT.IN EXTREME CIRCUMSTANCES IT

CAN CAUSE THE BOLT TO SWELL.

Charge Port

Cover

Omen Manual 2.0 6/21/05 9:56 AM Page 8

DO NOT EXCEED RECOMMENDED INPUT OR OPERATING PRESSURE. FILLING COMPRESSED

GAS / A I R

An overfill of any compressed gas or air cylinder can cause

the safety burst disk (Figure 5) on the cylinder to burst, or the

cylinder itself to rupture.A cylinder may rupture with

extremely dangerous,and potentially lethal force.Use

properly rated discs only.Inspect the burst disc for a vent

hole. If no hole is present contact a local store or PMI

immediately. DO NOT FILL!

A scale must be used for all CO2fills to prevent an overfill. A pressure gauge must be used

for all compressed gas or air fills to prevent an overfill.

Fills must be performed by qualified personnel. A cylinder must not be filled beyond the

cylinder’s capacity per the U.S. Department of Transportation. A cylinder’s rated capacity

appears on the cylinder itself.

Use only CO2tanks with an anti-siphon tube installed for best results.

Figure 5. Safety burst

disk.

The EVIL OMEN™paintball marker may be powered by anti-siphon CO2but it is

recommended that Nitrogen or Compressed Air be used for best performance.

THE SAFETY RULES FOR HANDLING COMPRESSED GAS OR AIR MUST BE

FOLLOWED AT ALL TIMES.

Figure 3. Valve-cylinder

connection.

Figure 4. Valve-cylinder

connection.

COMPRESSED GAS/AIR

WARNING

COMPRESSED GAS/AIR

WARNING

O P E R ATING PRESSURE AND INPUT

P R E S S U R E

• Operating pressure range: 250-500 p.s.i.

• Recommended maximum input pressure is 500 p.s.i. for marker.

• Maximum inlet to regulator 1000 p.s.i.

• Do not exceed recommended pressures.

DO NOT LEAVE CYLINDER OR PRESSURIZED MARKER IN DIRECT SUNLIGHT

OR EXPOSED TO HEAT SOURCE. INCREASED TEMPERATURE WILL INCREASE

THE PRESSURE OF COMPRESSED GAS OR AIR TO DANGEROUS LEVELS.THIS IS

ESPECIALLYTRUE WITH CO2.

VA LV E - C YLINDER CONNECTION

The valve on a cylinder is to remain screwed into the cylinder;

Figures 3 and 4. Should it loosen, the cylinder may detach from

the valve with extremely dangerous force.Call manufacturer

or take to qualified personnel for inspection if valve and cylinder

begin to separate.

Every time a cylinder is filled, the connection between the valve

and cylinder must be inspected. If any looseness or leak is

detected between the valve and the cylinder,do not fill. Drain

cylinder and call manufacturer or take to qualified personnel

for inspection.

A COMPRESSED GAS OR AIR CYLINDER IS A PRESSURE VESSEL. FOLLOW RULES FOR

SAFE HANDLING OF COMPRESSED GAS OR AIR. ALL FILLING OF COMPRESSED

GAS OR AIR CYLINDERS,AND ALL REPAIRS TO A MARKER’S AIR SYSTEM OR ITS

COMPONENTS MUST BE PERFORMED BY QUALIFIED PERSONNEL.

DO NOT OVERFILL ANY CYLINDER. AN OVERFILL CAN CAUSE THE SAFETY BURST DISK

OR THE CYLINDER ITSELF TO RUPT U RE.

HYDROSTATIC TESTING DATE

Many cylinders are required by the U.S. Department of Transportation to be hydro tested

at periodic interva l s, with the interval varying according to cylinder type. The date of the

cy l ind e r’s initial or later testing appears on the cylinder. A cylinder that is out of date for

hydrostatic testing must not be filled or used.

Omen Manual 2.0 6/21/05 9:56 AM Page 10

1. Chronograph the marker using standard chronograph procedures and

following safety rules.Shooting velocity will vary based upon many

factors,such as paint, weather,and air system.

2. Velocity of the EVIL OMEN™is normally adjusted by rotating the

adjusting ring on the regulator. The thread used in this ring is a fine

pitch, allowing for very small adjustments to be made accurately.

Generally,increasing output pressure increases paintball velocity.

(However,see TUNING for a discussion of how excessive regulator

output pressure actually decreases velocity).

To adjust velocity,first loosen the locking screw (3/32 allen wrench

provided) and back the locking screw off three full turns.If the locking

screw is not backed off far enough you will be unable to turn the

adjusting ring. The adjusting ring should turn easily; DO NOT FORCE IT!

NOTE: When turning the Adjusting Ring to reduce velocity, it

is necessary to cycle (shoot) the marker every 1/2 turn. This

is done to relieve the captive pressure in the downstream

portion of the gas system. Failure to do this will result in

premature wear to the sealing seat in the regulator. The

gauge will NOT move unless you cycle the marker as you

adjust the pressure down.

DO NOT EXCEED 300 FPS! You must have a chronograph to know

your speed. Paintballs fired over 300 fps can cause permanent

damage and injury and the extra wear and tear on the marker

may void your warranty.

3. Anytime the velocity is adjusted at the inline regulator,you should also

adjust the recock screw for best performance.If you turn your inline pressure up,you

will have to turn the recock pressure down slightly (Figure 7). See page 26 for complete

tuning instructions.

4. Chronograph the marker after every velocity or pressure adjustment.

5. Chronograph the marker at regular intervals during the day,as well as any time the air source

is refilled or changed, any time the barrel, brand, type of paintballs used, or any part in the air

system is changed, and upon request of any player or game official.

V E L OCITY ADJUSTMENT

WARNING

EVIL OMEN™SPECIFICATIONS

Action: Semi-automatic, true closed bolt cycle,pneumatic recock,

electro-mech firing control, independent hammer and

recock piston (patent pending), external recock regulation

(patent pending)

Length: 19.7 inches

Weight: 2lbs., 7oz

Height: 8 inches

Barrel: 15/16-20 TPI (AC) Stiff Arbor Honed, 0.689 first stage to

0.700 second stage

Special patented anodizing process for durability and low

drag coefficient

14 inch Driver Barrel with Autococker Threads

Feed: CAM operated Force feed system with anti-doubler arm

(patent pending) and shock absorbing buffer

Paintballs: For use only with standard “.68 caliber” (.68-inch diameter)

paintballs

Air Source: Accepts standard connections for CO2,regulated N2,or

regulated compressed air

Omen Operating Pressure: 200-500 psi recommended

Marker Pressure: not to exceed 500 p.s.i.

Input Pressure to EVIL Detonator: not to exceed 1000 p.s.i.

Air Source Input: bottom line on/off assembly

Grip: Custom panels to fit 45 style frame

Safety: On/Off switch and barrel blocking device (included)

Pursuit Marketing, Inc. (PMI Inc.), reserves the right to modify or change its markers without

incurring any obligation to incorporate such modifications or changes in any of its products

that were sold prior to the modification. The information in this operator’s manual may be

updated or changed without notice.

This operator’s manual is intended to remain with the paintball marker upon any subsequent

transfer of the marker, whether through sale, resale, or furnishing in any manner.A replacement

operator’s manual may be obtained from Pursuit Marketing, Inc., 55 Howard Ave, Des Plaines,

Illinois USA; phone 800.579.1633; www.evil-paintball.com

ALL PAINTBALL MARKERS MUST BE CHRONOGRAPHED REGULARLY. ADJUST

MARKER TO SHOOT PAINTBALLS AT A VELOCITY THAT IS LESS THAN 300 FEET PER

SECOND (FPS) AND THAT DOES NOT EXCEED THE VELOCITY LIMIT SET BY THE

PAINTBALL PARK WHERE THE MARKER IS IN USE.

CHRONOGRAPH THE MARKER AT REGULAR INTERVALS DURING THE DAY, AS WELL

AS ANY TIME THE AIR SOURCE IS REFILLED OR CHANGED,ANY TIME THE

BARREL OR ANY PART IN THE AIR SYSTEM IS CHANGED,AND UPON REQUEST OF

ANY PLAYER OR GAME OFFICIAL.

–

Figure 6.

Figure 7.

–

Re-cock Screw Adjustment

Omen Manual 2.0 6/21/05 9:56 AM Page 12

E V I L O M E N ™PA R TS LO C AT I O N

Bolt-Powered Cam Feed

System (Patent Pending)

Venturi Style Delrin Bolt

Independent Hammer and Recock

Piston (Patent Pending)

On/Off Bottomline

9V Rechargeable

Battery

Adjustable

Double Trigger

On / Off Safety Switch

Adjustable Recock

Pressure (Patent Pending)

Charge Port

Inline EVIL

Detonator™

Rear Block

Cocking Rod

Beavertail

Indicator LED

LPC

No Rise Feed Tube

Easy Strip Hinged Cam Feed Cover

EVIL™ Driver Barrel

Regulator

Locking Screw

Omen Manual 2.0 6/21/05 9:56 AM Page 14

16 17

Pursuit Marketing, Inc., thanks you for purchasing this high quality EVIL OMEN™paintball marker. Please read each of the

following items and initial that you have read and understood it before operating the EVIL OMEN™paintball marker:

1. This paintball marker is intended for sale to adults only,for use in compliance with all applicable laws and

regulations. Adult supervision is recommended at all times whenever a minor is handling this paintball marker in any

manner. Please initial: ______

2. Always wear protective goggles and headgear specifically designed for paintball when shooting this marker.

Please initial: ______

3. Every person within range of an area where a paintball marker is in use must wear protective goggles and headgear

specifically designed for paintball. Please initial: ______

4. Operate a paintball marker only in areas where it is safe and lawful to do so.Please initial: ______

5. Misuse of this paintball marker can result in criminal penalties including jail time.Please initial: ______

6. Read this operator’s manual completely before loading, pressurizing, or operating the EVIL OMEN™ paintball

marker. Please initial: ______

7. Never aim or shoot a paintball marker toward any person who is not wearing protective goggles and headgear

specifically designed for paintball. Please initial: ______

8. During game play,follow referee’s instructions and all field safety rules.Avoid shooting at a player’s head, neck, or

groin area. Please initial: ______

9. Play paintball only where the rules of safe paintball play are followed. Please initial: ______

10. All paintball markers must be chronographed regularly.Adjust marker to shoot paintballs at a velocity that is less

than 300 feet per second (fps) and that does not exceed the velocity limit set by the paintball park where the marker

is in use.Chronograph the marker at regular intervals during the day,as well as any time the air source is refilled

or changed, any time the barrel or any part in the air system is changed, and upon request of any player or game

official. Please initial: ______

11. This paintball marker operates using compressed gas or air at specified input pressure ranges. Follow safety

procedures when handling compressed gas or air.All filling of compressed gas or air cylinders must be done by

qualified persons.Please initial: ______

12. Follow the rules of safe marker handling: Keep finger off trigger until ready to shoot. Keep muzzle pointed in a safe

direction. In addition, firmly insert a barrel plug into the muzzle and push the mechanical safety “on” when the

marker is not in use and when in any non-shooting area. Please initial: ______

13. Never shoot at domestic animals or wildlife.Please initial: ______

14. Never mark objects outside the confines of the game or authorized shooting areas.Please initial: ______

15. Never look down the barrel of the marker. Please initial: ______

16. Before disassembly, storage, or transport of the marker, remove all paintballs from the marker, barrel, and loader;

remove air source; and remove all gas or air from the air system. Insert barrel plug and put electronic safety

in “no shoot” position. Please initial: ______

17. Carry marker in case or sturdy bag when in public. Please initial: ______

18. Safely and securely store marker to prevent access to it by unauthorized persons.Please initial: ______

EVIL OMEN™2.0 WARRANTY REGISTRATION

Please fill out entirely this EVIL OMEN™Warranty Registration form including the checklist and mail it to:

Pursuit Marketing, Inc., 55 Howard Ave, Des Plaines,IL 60018 USA, or register online at www.evil-paintball.com.

Save your original sales purchase receipt or packing slip.A copy must accompany the marker when warranty repairs are sought.

Consult operator’s manual for warranty information and instructions on obtaining repair service.

Purchaser’s name:

Mailing address:

City, State, Zip:

Phone number:

E-Mail Address:

Age:

Model purchased:

Serial number:

(Serial number is located on the left hand side above the grip frame)

Where purchased:

Date of purchase:

Seller’s name:

Seller’s address:

City, State, Zip:

Purchase price:

THE EVIL OMEN™ PAINTBALL MARKER IS NOT A TOY. MISUSE MAY CAUSE

SERIOUS INJURY OR DEATH. EYE PROTECTION DESIGNED FOR PAINTBALL USE

MUST BE WORN BY THE USER AND ANY PERSON WITHIN RANGE. READ THIS

OPERATOR’S MANUAL COMPLETELY BEFORE LOADING,PRESSURIZING,OR

OPERATING THE EVIL OMEN™ PAINTBALL MARKER. Please initial: _____

WARNING

Omen Manual 2.0 6/21/05 9:56 AM Page 16

RULE THE WORLD

O M E N ™2.0 RECEIVER BARREL DIAG R A M

01 Feed Tube (black) 57775

02 Cover Plate (black) 57008

03 Cover Plate Screw 57704

04 Pivot Cover (black) 57821

05 Ball Bumper 57724

06 Cam Pin Threaded 57710

07 Pivot Cover Screw 57768

08 Body (black) 57000

08a Gauge 46998

09 Pivot Cover Hinge Pin 57703

10 Recock Screw 57757

11 Recock Screw O-Ring (003-70 U) 10256

12 Field Strip Pin Assembly 57705

13 Valve Body O-Ring (015-70 or 90) 57738

13 Vertical ASA O-Ring (015-70 or 90) 57738

13a Vertical ASA O-Ring (12/70) 10257

14 Valve Body Assembly 57104

14a Valve Spring Guide 57773

15 Valve Stem 57707

16 End Cap O-Ring (019-70) 57728

17 Valve Spring 57721

18 LPC (black) 57826

19 Valve Body Locating Scre w 57706

20 Vertical ASA (black) 57007

21 Gas Thru Bolt 57709

22 Field Strip Pin Ball 10130

23 Field Strip Pin Spring 10150

24 Cam Spring 57723

25 Cam Detent Screw 57727

26 Cam Arm57725

27 Anti Doubler Arm57726

Omen Manual 2.0 6/21/05 9:56 AM Page 18

Andere Evil Paintball-Ausrüstung Handbücher

Evil

Evil Pimp Kit Bedienungsanleitung

Beliebte Paintball-Ausrüstung Handbücher anderer Marken

PLANET ECLIPSE

PLANET ECLIPSE EGO LV1 Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GEO CS1 Bedienungsanleitung

First Endeavor Paintball

First Endeavor Paintball The Quest Bedienungsanleitung

PMI

PMI Piranha VTL Bedienungsanleitung

Proto

Proto SLG ULTRALITE Bedienungsanleitung

Bob Long Technologies

Bob Long Technologies Alias Intimidator Bedienungsanleitung

Proto

Proto REFLEX RAIL Bedienungsanleitung

MCS

MCS BOX DRIVE Bedienungsanleitung

Spyder

Spyder MR1 Bedienungsanleitung

GOG

GOG Envy Leitfaden

PLANET ECLIPSE

PLANET ECLIPSE GSL Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE GTEK M170R Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE CS3 .68CAL Gebrauchsanweisung

Proto

Proto SWITCH EL Bedienungsanleitung

Empire

Empire MINI Bedienungsanleitung

Psychoballistics

Psychoballistics SILVER BULLET LCD Bedienungsanleitung

Virtue

Virtue SPIRE III Bedienungsanleitung

PLANET ECLIPSE

PLANET ECLIPSE MG 100 Bedienungsanleitung