Evolution Aqua Evo15 Bedienungsanleitung

English

EVO010121MAN

WARNING:

• Ensure that the unit is switched off at the mains before you attempt to conduct

any type of maintenance on the UVC.

• Ensure the unit is installed in the recommended orientation.

• Fit the quartz sleeves and O-rings and switch on pump to check that unit is water

tight before fitting the bulb, bulb socket and end cap.

• Ensure that the end cap is tight before running the unit.

• After replacing bulbs or before tightening the end cap, make sure that the O-Rings

are in the correct position, and the bulb sockets are dry.

• If the electrical connections get wet, dry thoroughly before switching power on.

• This unit should only be installed by a qualified electrician.

INSTALLATION AND OPERATING MANUAL

Complete instructions for all models of evoUV

Evolution Aqua Ltd. Kellet Close - Wigan - Lancashire - United Kingdom - WN5 0LP

t +44 (0) 1942 216554 - e[email protected] - wwww.evolutionaqua.com

Downloaded from http://www.watergardeningdirect.com

IMPORTANT SAFETY INSTRUCTIONS

- READ AND FOLLOW ALL INSTRUCTIONS

- WARNING - To reduce the risk of injury, do not permit children to use this product

unless they are closely supervised at all times. This appliance is not intended for use by

persons (including children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

- WARNING - Risk of Electric Shock. Connect only to a branch circuit protected by a

ground-fault circuit interrupter (GFCI). Contact a qualified electrician if you cannot verify

that the circuit is protected by a GFCI.

- WARNING - If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

- WARNING - To reduce the risk of electric shock, do not use extension cord to

connect unit to electric supply; provide a properly located outlet.

- WARNING - Do not operate the UV-C emitter when it is removed from the appliance

enclosure.

- Unintended use of the appliance or damage to the housing may result in the escape of

dangerous UV-C radiation. UV-C radiation may, even in little doses, cause harm to the

eyes and skin. Never look directly at an illuminated UV bulb.

- Appliances that are obviously damaged must not be operated.

- Do not run this unit dry. Please ensure that the unit is full of water before switching it on.

- Always isolate the unit from mains electricity and turn off any water supply before carrying

out any maintenance.

- Always disconnect all pond appliances from the mains supply before putting

your hands into the water.

- Use in the area only if the installation complies with the relevant wiring

regulations.

- Power must be supplied through a Residual Current Device (RCD) with a

residual operating current not exceeding 30mA.

- This unit must be earthed when earth wire is fitted.

- Never use a fuse larger than 3 amps on the power lead.

- The unit must not be submerged in water.

- If the quartz sleeve is cracked, replace it immediately.

- The unit must be fully frost protected or taken inside during winter months.

SAVE THESE INSTRUCTIONS

Downloaded from http://www.watergardeningdirect.com

CONTENTS

UV Diagram and components list PAGES 4 - 6

Flow Rates PAGE 7

Installing the quartz sleeve PAGE 8

Positioning and mounting the UV PAGE 9

Connection to your pipework PAGE 11

Water Testing PAGE 14

Connection to the Electricity Supply PAGE 15

Installing the UV bulb PAGE 16

UV Bulb Replacement PAGE 17

Replacing / Cleaning the Quartz Sleeve PAGE 18

Electrical box replacement PAGE 19

In Built Protection PAGE 19

Trouble Shooting PAGE 20

Frequently Asked Questions PAGE 21

Guarantee PAGE 22

UNBOXING THE UV

On unpacking, you will see that the UV bulb and quartz sleeve are packed separately for safe

transit. Please refer to pages 8 and 16 of this manual for instructions on how to install the bulb

and quartz sleeve. Quartz Sleeve O-Rings and End Cap Flat Washers are packed in separate

small bags inside the box.

Stainless steel mounting brackets and screws are also supplied in bags and need to be fitted.

On the 110 UV, the mounting brackets can be found in the cardboard end fitments.

Please take time to familiarise yourself with your UV and its components.

INTRODUCING THE EVOLUTION AQUA EVO UV

Congratulations on purchasing an Evolution Aqua evoUV. Our range of evoUV pond clarifiers

have been manufactured using the latest technology and design techniques. evoUVs have

been designed to clear green water which is caused by single celled green algae, and

prevent it from returning. evoUVs will work alongside many different filtration systems but

when used alongside Evolution Aqua’s pond filtration systems, the evoUV will deliver crystal

clear and healthy pond water.

Please read this instruction manual carefully from start to finish before attempting to install

your evoUV.

Downloaded from http://www.watergardeningdirect.com

(B) (C)(D) (H) (G)

(F)

(I)

(E)

(A)

(J) (K) (L)

15W AND 25W UV DIAGRAMS AND COMPONENTS LIST

Please familiarise yourself with the components shown in the diagram below:

These are packed in small bags

inside the packaging.

Order code: EVOUVSPARESML

You will receive two quartz sleeve

O-Rings and two end cap flat

washers with this spare part.

IDENTIFYING THE O-RINGS

2 x Quartz Sleeve

O-Ring (G)

2 x End Cap

Flat Washer (I)

Round

O-Ring

Flat

Washer

Description Label Qty Order Code

Inlet / Outlet - 1½Hosetail A 2 HOSETAIL15TH

End Cap B 2 EVOCONNUT

UV Bulb C 1 Available from your EA dealer

Quartz Sleeve D 1 Available from your EA dealer

Hosetail O-Ring E 2 EVOUVORINGHOSET

Bulb Socket F 2 LAMPHOLDER-T8

Quartz Sleeve O-Ring G 2 EVOUVORING2

Locking Nut H 2 EVO-M/F

End Cap Flat Washer I 2 EVOUVFLATWASHER

Electrical Box J 1 Available from your EA dealer

Cable Clip K 2 -

Mounting Bracket L 2 -

Downloaded from http://www.watergardeningdirect.com

30W / 55W / 75W UV DIAGRAMS AND COMPONENTS LIST

Please familiarise yourself with the components shown in the diagram below:

(B)

(G)

(F)

(I)

(E)

(A)

(K) (L)

(J)

Description Label Qty Order Code

Inlet / Outlet - 1½Hosetail A 2 HOSETAIL15TH

End Cap B 2 EVOCONNUT

UV Bulb C 1 Available from your EA dealer

Quartz Sleeve D 1 Available from your EA dealer

Hosetail O-Ring E 2 EVOUVORINGHOSET

Bulb Socket F 2 LAMPHOLDER-T8

Quartz Sleeve O-Ring G 2 EVOUVORING2

Locking Nut H 2 EVO-M/F

End Cap Flat Washer I 2 EVOUVFLATWASHER

Electrical Box J 1 Available from your EA dealer

Cable Clip K 2 -

Mounting Bracket L 2 -

These are packed in small bags

inside the packaging.

Order code: EVOUVSPARESML

You will receive two quartz sleeve

O-Rings and two end cap flat

washers with this spare part.

IDENTIFYING THE O-RINGS

2 x Quartz Sleeve

O-Ring (G)

2 x End Cap

Flat Washer (I)

Round

O-Ring

Flat

Washer

Downloaded from http://www.watergardeningdirect.com

(B)

(G)

(F)

(I)

(J)

(A)

(L)

110W UV DIAGRAMS AND COMPONENTS LIST

Please familiarise yourself with the components shown in the diagram below:

For European models two 2" imperial to 63mm metric reducers are supplied.

Description Label Qty Order Code

Inlet / Outlet A - -

End Cap B 4 EVOCONNUT

UV Bulb C 2 Available from your EA dealer

Quartz Sleeve D 2 Available from your EA dealer

Bulb Socket F 4 LAMPHOLDER-T8

Quartz Sleeve O-Ring G 4 EVOUVORING2

Locking Nut H 4 EVO-M/F

End Cap Flat Washer I 4 EVOUVFLATWASHER

Electrical Box J 1 Available from your EA dealer

Mounting Bracket L 2 -

These are packed in small bags

inside the packaging.

Order code: EVOUVSPARELGE

You will receive four quartz sleeve

O-Rings and four end cap flat

washers with this spare part.

IDENTIFYING THE O-RINGS

4 x Quartz Sleeve

O-Ring (G)

4 x End Cap

Flat Washer (I)

Round

O-Ring

Flat

Washer

Downloaded from http://www.watergardeningdirect.com

FLOW RATES

Please note: For optimum performance we recommend that you pass the entire volume of

your pond through the evoUV unit once every 2 to 3 hours. We do not recommend the use

of pumps with operating pressures in excess of 3 bar.

Your evoUV will keep your pond clear of green water up to its maximum capacity.

However, it is important to note that there are factors that affect how you select the right

size of evoUV for your pond.

You will need to take into consideration such things as stocking levels, sunlight / shade,

daily sunshine amounts etc. This is not always possible to calculate, and if this is the

case, use the tables below as a guide. It must be stressed however, that these are only

guidelines, and you should take advice from your local Evolution Aqua dealer

USA - Southern States / Mediterranean 3 Watts UV per 1,000 litres

Northern Europe including UK 2 Watts UV per 1,000 litres

USA - Northern States / Canada 1 Watts UV per 1,000 litres

*evo110 offers even more UV per volume than the evo75 for more demanding situations

Model Max. pond size Max. flow rate Bulb power Inlet /

Outlet Fittings

supplied

evo15 15,000 Litres

3,300 UK Gallons

3,963 US Gallons

7,500 Litres/hr

1,650 UK Gallons/hr

1,982 US Gallons/hr 15W (1 x 15W T8) 1½" 2 x 1½"

Threaded

Hosetails

evo25 20,000 Litres

4,400 UK Gallons

5,284 US Gallons

10,000 Litres/hr

2,200 UK Gallons/hr

2,642 US Gallons/hr 25W (1 x 25W T8) 1½" 2 x 1½"

Threaded

Hosetails

evo30 30,000 Litres

6,600 UK Gallons

7,925 US Gallons

15,000 Litres/hr

3,300 UK Gallons/hr

3,962 US Gallons/hr 30W (1 x 30W T8) 1½" 2 x 1½"

Threaded

Hosetails

evo55 55,000 Litres

12,100 UK Gallons

14,530 US Gallons

20,000 Litres/hr

4,400 UK Gallons/hr

5,284 US Gallons/hr 55W (1 X 55W T8) 1½" 2 x 1½"

Threaded

Hosetails

evo75 75,000 Litres

16,500 UK Gallons

19,815 US Gallons

25,000 Litres/hr

5,500 UK Gallons/hr

6,605 US Gallons/hr 75W (1 X 75W T8) 1½" 2 x 1½"

Threaded

Hosetails

evo110 75,000 Litres

16,500 UK Gallons

19,815 US Gallons

25,000 Litres/hr

5,500 UK Gallons/hr

6,605 US Gallons/hr 110W (2 X 55W T8) 2" No

Fittings

Supplied

POND IS IN

FULL SHADE POND IS IN

PART SHADE POND IS IN

FULL SUN

POND SIZE

LOW

STOCK HIGH

STOCK LOW

STOCK HIGH

STOCK LOW

STOCK HIGH

STOCK

<7,500 Litres

<1,650 UK Gallons

<1,982 US Gallons

evo15 evo15 evo15 evo15 evo15 evo25

<15,000 Litres

<3,300 UK Gallons

<3,963 US Gallons

evo15 evo25 evo15 evo25 evo25 evo30

<20,000 Litres

<4,400 UK Gallons

<5,284 US Gallons

evo25 evo30 evo30 evo30 evo30 evo55

<30,000 Litres

<6,600 UK Gallons

<7,925 US Gallons

evo30 evo55 evo55 evo55 evo55 evo55

<55,000 Litres

<12,100 UK Gallons

<14,530 US Gallons

evo55 evo75 /

evo110* evo75 /

evo110*

<75,000 Litres

<16,500 UK Gallons

<19,815 US Gallons

evo75 /

evo110* evo75 /

evo110*

Downloaded from http://www.watergardeningdirect.com

INSTALLING THE QUARTZ SLEEVE

End Cap (B) UV Bulb (C)

Bulb Socket (F)

End Cap Sealing Ring (I)

Quartz

Sleeve (D) Thread

Quartz

Sleeve

O-Ring (G)

Locking

Nut (H)

1. Starting at one end of the unit, unscrew the black end cap (B). You will notice

that this black end cap houses the bulb socket (F).

2. Unscrew the white locking nut (H) from the same end.

3. Repeat steps 1 and 2 at the other end of the unit.

4. Take the quartz sleeve (D) from the packaging box and slide it through the UV until it

finds the hole at the far end of the unit.

5. Take the quartz sleeve O-Ring (G) and fit it around one end of the quartz sleeve.

6. Slide this quartz sleeve O-Ring (G) towards the thread on the UV body,

ensuring that equal amounts of quartz sleeve are visible at each end of the unit.

7. Fit the quartz sleeve O-Ring

(G) at the other end of the

quartz sleeve, again ensuring

that equal amounts of quartz

sleeve are visible at each

end of the unit.

8. Now screw the white locking

nut (H) back into position.

9. Ensure the locking nut

is HAND TIGHTENED to

prevent causing damage to

the O-Ring. No tools

are needed.

10. Repeat steps 8 and 9 at the other end of the unit.

11. The quartz sleeve is now in position ready to take the UV bulb.

12. Run for 24 hours to check the installation is correct with no leaks. See page 14 for

details. Re-install if any leaks are detected - if no leaks proceed to lamp installation.

EQUAL AMOUNTS MUST BE VISIBLE

IMPORTANT: Ensure that equal amounts of the

quartz sleeve are visible at each end of the unit

before fitting the locking nuts.

HAND TIGHTEN FITTINGS ONLY - DO NOT USE TOOLS

Downloaded from http://www.watergardeningdirect.com

POSITIONING AND MOUNTING THE UV

Fitting mounting brackets (15W to 75W)

Stainless steel brackets and screws can be found in bags inside the packaging.

You will need to install these mounting brackets to the rear of the UV at each

end using a 3mm allen key. HAND TIGHTEN ONLY.

Fitting mounting brackets (110W)

Stainless steel mounting brackets, nuts and bolts can be found inside the packaging.

On the 110 UV, you can find the two mounting brackets inside the cardboard fitting

inside the box. Nuts and bolts are packed in a small bag. You will need to install

these mounting brackets to the rear of the UV at each end. Use a 8mm nut runner

and spanner. HAND TIGHTEN ONLY.

3mm

8mm 3mm 3 Core

Mains Cable

Length according to installation

6mm

3mm

8mm

3mm 3 Core

Mains Cable

Length according to installation

6mm

3mm 8mm 3mm 3 Core

Mains Cable

Length according to installation

6mm

Downloaded from http://www.watergardeningdirect.com

POSITIONING AND MOUNTING THE UV

If you are going to position your evoUV outside or in an area where it is likely to get splashed

regularly with water, then you must mount the unit the correct way up. If your evoUV will be

positioned in a permanently dry environment then it can be installed in any position.

Your evoUV must not be submerged in water or placed in a position where water may collect

around the unit. The electrics within the evoUV units are sealed in a showerproof unit. evoUV

has an IP rating of X5.

Please ensure that there is enough space at one end of the evoUV to enable bulb / quartz

sleeve removal and maintenance.

PLEASE NOTE: Wall mounting screws and wall plugs are not provided.

If installing the unit prior to or without a pond filter, we would recommend the use of a

pre-filter on the water pump to prevent excess solids from being pumped into the unit.

The evoUV may be connected to the water flow on any pumped line, this could be,

for instance, a skimmer line or any other additional pumped line. The two most common

forms of set up are pump fed and gravity fed, shown below:

POND

Pump

Raised 12”

off ground

1½” or 2” Pipe

1½” or

2” Pipe

4” Pipe

Return to pond

Gravity Fed Installation

Pump Fed Installation

We recommended installing a ball valve either side of the evoUV for maintenance.

POND

Water Level Return to pond

Alternative return via waterfall / blade

Alternative

return

Water

Pump 4” Pipe

1½” or 2” Pipe

Downloaded from http://www.watergardeningdirect.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Evolution Aqua Wasserfiltersystem Handbücher

Evolution Aqua

Evolution Aqua Nexus Series Kurzanleitung

Evolution Aqua

Evolution Aqua Nexus Eazy 200 Handbuch

Evolution Aqua

Evolution Aqua PURE POND 5,000 Bedienungsanleitung

Evolution Aqua

Evolution Aqua EAZYPOD AUTOMATIC Kurzanleitung

Evolution Aqua

Evolution Aqua eazypod Kurzanleitung

Evolution Aqua

Evolution Aqua NExus 300 Handbuch

Evolution Aqua

Evolution Aqua evoUV Series Bedienungsanleitung

Evolution Aqua

Evolution Aqua Cetus sieve Kurzanleitung

Evolution Aqua

Evolution Aqua eazypod Handbuch

Evolution Aqua

Evolution Aqua Cetus sieve Bedienungsanleitung

Evolution Aqua

Evolution Aqua eazypod Handbuch

Evolution Aqua

Evolution Aqua nexus 310 Kurzanleitung

Evolution Aqua

Evolution Aqua Nexus Eazy 200 Handbuch

Evolution Aqua

Evolution Aqua eazypod Handbuch

Evolution Aqua

Evolution Aqua eazypod complete Bedienungsanleitung

Evolution Aqua

Evolution Aqua K1 MICRO BEAD 20 Kurzanleitung

Evolution Aqua

Evolution Aqua Tempest Bedienungsanleitung

Evolution Aqua

Evolution Aqua NExus 300 Bedienungsanleitung

Evolution Aqua

Evolution Aqua Nexus Eazy 200 Kurzanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung

Evolution Aqua evo15 Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken