Evolution MK-425C Bedienungsanleitung

Evolution MK-425C • MK-449C • MK-461C

User Guide

Evolution MK-425C • MK-449C • MK-461C

English

Table of Contents

Evolution Advanced Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

About The Advanced Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Edit Mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Default mode : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Programming & Editing The MK-425C/449C/461C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Introduction To Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Selecting A Controller For Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assigning MIDI CC’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assigning An Individual MIDI Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setting Toggle Values For The Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

RPN/NRPN, GM 1+2 SysEx & Other Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assigning MMC Control To A Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assigning RPN/NRPN To A Fader/Rotary Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Assigning A Note To A Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About SysEx Messages & Device ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Non-Volatile Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Memory Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Assigning Device ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Resetting To The Factory Default Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

MIDI Messages Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Program & Bank Changes Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

RPN/NRPN’s Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SysEx Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

The Evolution Librarian Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

About The Evolution Librarian Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing The Evolution Librarian Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting Up The Librarian Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Librarian Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Organising Presets Received From A Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Viewing The Contents Of A Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Saving A Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Loading A Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Future Development Of The Librarian . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Technical, Contact and Warranty Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Technical Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Appendix A –G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

MIDI IMPLEMENTATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Appendix B - Assignable MIDI CC’s on the MK-425C/449C/461C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

B1 - The Faders and rotary Controllers: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

B2-The Buttons: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Appendix C - Hexadecimal Conversion Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Hexadecimal to Decimal Conversion Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Appendix D - Useful MIDI data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

General MIDI Instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

MIDI Note Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Appendix E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Standard MIDI Controller numbers (MIDI CC’s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Appendix F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Roland GS and Yamaha XG NRPN Support to Roland JV/XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

General MIDI Reverb and Chorus Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Evolution MK-425C • MK-449C • MK-461C

English

Evolution Advanced Guide

About The Advanced Guide

In the MK-425C/449C/461C Advanced Guide we have made the assumption that you have been through the Getting Started Guide which should

have been supplied in printed form with your keyboard. If you do not have this guide, please contact your local distributor or download it from our

website www.evolution.co.uk

The Getting Started Guide should insure that you are now familiar with the basic operation of the keyboard so that we now can focus on more in-

depth features.

First however, we need to explain some terminology we use throughout the guide.

Terminology

Edit Mode:

Edit Mode describes the short period after a function button has been pressed during which the parameters of that function can be altered. The

numeric keypad can be used to alter a parameter during this time. No data is sent out of the Evolution MK-425C/449C/461C when it is in Edit

mode except for program and bank changes. LCD symbols shown in Edit mode will ﬂash to show you that a particular parameter can be edited. If

a number is part entered, and a new controller turned, that number will become the relevant parameter number for the new controller and the 3

second editing period will re-trigger.

Default mode :

Default Mode describes the state of the keyboard, when no function buttons have been pressed within the last 3 seconds. In Default mode, the

LCD will show the controller symbol, and the 2 digit display will show the last selected controller. The 3 digits display the currently assigned MIDI CC

number.

Programming & Editing The MK-425C/449C/461C

Introduction To Programming Options

Each of the MK-425C/449C/461C’s controllers can send MIDI cc, RPN/NRPN, GM 1&2 SysEx messages and even be assigned to individual MIDI

channels.

MIDI cc (continuous controller) numbers are part of the standard MIDI speciﬁcations and are typically used to control the real-time changing of

parameters in musical equipment. For a complete list of standard MIDI controller numbers from 0 to 131, please see Appendix E on page 16.

Any of the real-time controllers on the keyboard can be assigned to a MIDI cc number however the 10 assignable buttons have slightly different

options from the 9 Faders (MK-449C/461C only) or rotary controllers.

The following 2 charts show all the transmit messages you can program for each of the fader/controllers and assignable MIDI buttons respectively.

We show you this already at this stage, so you can follow the principle of programming the controllers in the following instructions and examples.

Please pay extra attention to the differences between how you program the faders or controllers and how you program the buttons.

pir

cseD

)ec

(

bsM

)

ciwT

(

 





 





 





































































 

 





















 

 













 







 























 



 























 













 























 



 













































 































 



























































































 



 





























 









 

























 



 

 







 

 















 

 

















 

























 

sre

ortnoC

& sre

daF

* Sysex messages - for details please see page 8.

** MMC Sysex messages, for details please see page 5.

*** This value cannot be typed in using the numerical keypad. Type in 144 and then press the + button to set this value.

NGISSA noitpircseD margorP

)

ciwT s

ser

sserP( BSL knaB

)

iwT

erP( bsM ataD

)



 















 











 



























 





















 





























































 

 





















 































 



 

 













 

 









  



 



 



















 



 



































 



















 













 























 







 

























 



























 

 

 

  







 













 















 





 











 















 











  



 















  







 























   



































 



 











 











 







 





















 













  

 

 

  ---

nott

IDI

* Sysex messages - for details please see page 8.

** MMC Sysex messages, for details please see page 5.

*** This value cannot be typed in using the numerical keypad. Type in 144 and then press the + button to set this value.

Selecting A Controller For Editing

Before you can assign a MIDI cc to one of the MK-425C/449C/461C’s controllers, you will need to select it for editing. There are 2 methods for doing

this:

1. Press CONTROL SELECT. The LCD will display the CONTROLLER symbol.

The symbol will be ﬂashing to indicate the controller settings can be altered. The 3-digit display will show the number of the currently

selected controller, proceeded by a ‘C’, or an ‘F’ if the controller is a fader.

2. Type in the number of the controller using the numeric keypad, or the +/- buttons.

Move a fader/rotary controller.

Simply moving a fader/rotary controller will make it the currently selected controller, ready for editing.

It is not possible to select any of the 10 numerical buttons by pressing them, since during edit mode, they are used to enter numerical values. To

program these buttons, please use the ﬁrst method. We have given the buttons 0 to 9 the following numbers for the selection process: MK-425C =

11-20, MK-449C = 20-29, MK-461C = 24-33 respectively.

Assigning MIDI CC’s

Once the controller you want to edit has been selected, you can change the assigned MIDI cc number in the following way:

1. Press “CONTROL ASSIGN”. The LCD will ﬂash the CC symbol.

The 3 digit display will indicate the currently assigned MIDI cc number.

2. Type in a new MIDI cc value using the numeric keypad or ‘+’ and ‘-’ buttons.

The MIDI controller number you select will be assigned to the currently selected controller, shown by the number on the small, 2-digit

display.

Example: After pressing ASSIGN, the display shows the cc symbol and in this case displays that currently the MIDI cc 07 is

assigned to fader/rotary controller number 33.

Evolution MK-425C • MK-449C • MK-461C

English

Assigning An Individual MIDI Channel

1. Select the controller you want to edit as described earlier.

2. Press “CHANNEL ASSIGN”.

The LCD will display the CHAN symbol and the 3-digit display will show the current channel assignment of the selected controller,

preceded by a ’c’. The small 2-digit display will show the currently selected controller for assignment.

3. Type the MIDI channel number (01-16) you want the controller to send to, using the numeric keypad or the +/- keys.

If the controller is assigned to channel 00, it will transmit on the global channel.

Setting Toggle Values For The Buttons

The 10 assignable buttons can each be assigned to toggle between two values. You may for instance want to send out value 15 when you ﬁrst

press the button followed value 74 when you press the button for a second time. This is how you do it:

1. Press the Function button labelled “DATA MSB” 2 times.

2. Type in 15 using the numerical keypad or the +/- keys.

3. Press the Function button labelled “DATA LSB” 2 times.

4. Type in 74 using the numerical keypad or the +/- keys.

If you want the button to send the same value every time you press it, simply type in the same value both times.

RPN/NRPN, GM 1+2 SysEx & Other Messages

As already described, the standard MIDI controller numbers range from 0 to 131. We have extended the list of MIDI cc’s that can be assigned to the

controllers of the keyboard to include RPN/NRPN, MMC and General MIDI 1&2 SysEx messages.

These advanced messages are as easy to program as a regular MIDI cc instruction by entering values 132 to 152 when programming MIDI cc’s. The

charts on page 6 (or Appendix B) show you what number correspond to each message.

To program the values required for these advanced messages, the MK-425C/449C/461C requires you to press the PROGRAM, DATA LSB and DATA

MSB buttons twice respectively. Pressing only once will send the program and bank change instructions “on the ﬂy” as described in the Getting

Started guide.

Lets look at a couple of examples to see how this works. Please refer to the charts on pages 3 & 4 so you get to grips with the principle:

Assigning MMC Control To A Button

1. Select the button you want to control the MMC message.

2. Press “CONTROL ASSIGN” on the MK-425C/449C/461C.

3. Type in “149” using the numerical keypad.

This is the number that corresponds to the MMC instruction, as per the charts on pages 3 and 4.

4. Press “CHANNEL” once.

5. Type in “127”, using the numerical keypad.

This ensures that the message is set to all device ID numbers. For more information about this, please read “About SysEx Messages &

Device ID” on page 6.

6. Press the “DATA LSB” button twice.

7. Enter a number from the chart on the next page to select the MMC message you want:

rebm

dnamm

C CMM

 







 

 





























 





 





 



























 

 





 



 



















Assigning RPN/NRPN To A Fader/Rotary Controller

Note: For a detailed description of RPN/NRPN data see section RPN/NRPN’s explained on page 8.

1. Select the desired control as described earlier.

2. Press “CONTROL ASSIGN” twice and while the display is ﬂashing, enter controller 132 for RPN coarse, 133 for RPN ﬁne,

134 for NRPN coarse or 135 for NRPN ﬁne.

3. Press “DATA MSB” twice to assign the number for the RPN/NRPN MSB.

4. Press DATA LSB twice to assign the number for RPN/NRPN LSB.

5. Press “CHANNEL ASSIGN” to assign the MIDI channel the message should be sent on.

You will ﬁnd most data sheets for synths that make use of NRPN’s will give the MSB and LSB values that you should enter into

DATA MSB and DATA LSB banks (also see Appendix F). However, some manuals may only give the hex values.

The MK-425C/449C/461C requires you to enter the decimal value. You can easily convert hexadecimal values to decimal using

the windows calculator. Simply select Scientiﬁc mode, select hex and enter the hexadecimal value you need to convert.

Press the Dec button to convert it to a decimal value.

Alternatively, use the look up table in Appendix C.

Assigning A Note To A Button

The following shows how to set a button to transmit a note on when pressed, and a note off when released.

1. Press “CONTROL SELECT” and press the “0” button.

2. Press “CONTROL ASSIGN” and enter ‘147’ this is the MIDI cc number that corresponds to Note on/off mode, as shown

in Appendix B.

3. Press “DATA MSB” twice and enter a value of ‘100’. This means when you press the button, a Note on message will

be sent out with a velocity of 100.

4. Press “DATA LSB” twice, and enter a value of ‘000’. This means when you release the button, a Note off message will

be sent out.

5. Press the “PROGRAM” button twice and enter ‘064’. This will mean you are sending out MIDI note 64 or E4, each time

you press the button. The MIDI note numbers are given in Appendix D.

This button mode has many uses. You can play a conventional sound on the keyboard while triggering samples and

effects on different MIDI channels from the buttons. You could even trigger video clips or a lighting rig.

Note: When you press the button in note mode, the LCD display will brieﬂy show the note velocity.

About SysEx Messages & Device ID

When transmitting SysEx messages, the individual control channel number does not deﬁne a transmit channel, but a device ID. This is made clear

since when you press the CHANNEL button, the Channel symbol will not be shown and there is no ’c’ in the 3 digit display.

Device ID’s range between 00 – 127. In most cases, you should set the device ID as 127. 127 means the SysEx message will be received by all

devices.

Please note that the device ID for a Sys Ex message assigned to a controller can not be changed using the Device ID buttons. These buttons are

used for varying the global device ID of the MK-425C/449C/461C.

Non-Volatile Memory

The MK-425C/449C/461C uses non-volatile memory so that you can continue where you left off even after powering down and restarting. The

current controller and channel assignments are stored whether you have stored your setup to a memory locations or not. Also stored is Draw Bar

mode (on/off), DATA LSB and DATA MSB data, global channel setting and last used memory preset.

Evolution MK-425C • MK-449C • MK-461C

English

Memory Dump

The dual press “MEMORY DUMP” buttons will send out a number of Sys Ex data packets that represent the 10 memories you have set up in your

MK-449C/461C (MK-225C:

Press “DATA LSB” and “RECALL” simultaneously to send out memory dump). This is useful for storing or backing up the contents of your memory

presets externally.

You can record the complete memory dump in to a standard sequencer. To recall the memory dump back, play the MIDI track containing the

recorded memory dump to the keyboard, making sure that the MK-425C/449C/461C’s drivers are selected as output for that particular track.

The current controller assignments are not affected by a memory dump, or a memory send to the keyboard. Once a memory dump has been sent

to the keyboard, you will need to recall a preset to access the new memory settings.

Assigning Device ID

The dual press “DEVICE ID” buttons will allow you to assign a Device ID to the MK-449C/461C (MK-225C: Press “PROGRAM and DATA MSB”). The

default Device ID is 127, which means when a memory dump is performed, that dump can be received by the same keyboard model, regardless

of the Device ID setting.

If a device ID is assigned to any number other than 127, the memory dump performed will be speciﬁc to MK-425C/449C/461C with the same device

ID. If the device ID of a MK-425C/449C/461C differs from the one recorded with the memory dump, the data will be ignored.

The device ID is a handy way of differentiating between multiple keyboards. Otherwise, we recommend you keep the device ID setting as 127.

When you press the Device ID buttons, you will see the small 2-digit display on LCD display ‘id’. The 3-digit display represents the assigned Device

ID. You can enter a new device ID using the numeric keypad, or the ‘+’ and ‘-’ buttons.

For more information on SysEx messages and device ID, please go to page 8.

Resetting To The Factory Default Setting

You can reset the MK-425C/449C/461C back to the factory defaults on power-up by holding down the +/- buttons.

Note: Restoring the Factory presets will erase all setups stored to memory.

MIDI Messages Explained

Program & Bank Changes Explained

The original GM MIDI speciﬁcation catered for only 128 voices, numbered from 0-127. It is possible to access a different voice by sending a program

change.

In order to expand on the GM set of voices, Bank changes were devised. Each bank contains 128 patches, that can be accessed using a program

change. There are 16,384 banks available, accessible by sending a 14-bit Bank change message. The ﬁrst 7 bits of this message are sent in a single

byte known as the Bank LSB. The last 7 bits are speciﬁed by another byte known as the Bank MSB. The BANK LSB is the most commonly used. This

allows for 128 bank changes, and often there is no need to send a Bank MSB.

You will ﬁnd almost all MIDI devices respond to the program change, but some that do not conform to the GM set of voices use the program change

message for other purposes. Many VST instruments have adopted this approach, allowing you to use a program change to change the instrument

patch. The FM7 by Native Instruments is a good example of this.

Bank changes are more rarely used, although they do exist. Bank changes are useful in manufacturer’s extensions to the MIDI speciﬁcation, such

as Roland’s GS speciﬁcation and Yamaha’s XG speciﬁcation. Both of these require you to specify a Bank change, in order to access the extra voices

and effects that these speciﬁcations provide.

Sending Program, Bank LSB and Bank MSB data is made simple using the Mk-425C/449C/461C. Simply press the PROGRAM, DATA LSB or DATA MSB

button and enter the program or bank change you wish to send.

RPN/NRPN’s Explained

Non-registered parameter numbers (NRPN’s) are device speciﬁc messages that enable the control of synths via MIDI. The MIDI speciﬁcation deﬁnes

parameter numbers to allow scope for manufacturers to specify their own controllers. The more common of these have been registered by the MIDI

Manufacturer’s Association and are part of the MIDI speciﬁcation (hence the term Registered Parameter Numbers – RPN’s). (See Appendix F.)

MIDI controllers 98 and 99 represent the NRPN LSB and MSB respectively, while 100 and 101 represent the RPN LSB and MSB. This can be seen from

the MIDI controllers list in Appendix D. To transmit an NRPN/RPN, these two controller messages are sent along with their user-speciﬁed values. A

further controller message and value needs to be sent to specify the (coarse or ﬁne) value adjustment. This is speciﬁed by controller number 6 (Data

entry) for coarse adjustments or number 38 for ﬁne adjustments.

A list of NRPN’s will always be given in the User Manual of a device that receives NRPN messages. It is always necessary that the NRPN MSB and LSB

are sent together. Both will be speciﬁed in the device’s manual. You may ﬁnd the manufacturer’s have only speciﬁed the numbers in Hexadecimal

format. In this case, use Appendix C to translate the value to Decimal.

Your Evolution keyboard makes the process of transmitting NRPN’s easy. All you need is to enter the appropriate NRPN LSB by pressing the LSB/DATA

button twice, enter the NRPN MSB by pressing the MSB/DATA button twice, and as you move the controller, an appropriate NRPN message will be

sent out. Assign NRPN coarse to make big sweeps, or NRPN ﬁne to make slight adjustments.

SysEx Explained

System Exclusive (SysEx) messages were deﬁned in the MIDI speciﬁcation to allow individual devices to have individual control via MIDI. The format

of SysEx messages allows for virtually any function to be performed via MIDI – so long as the receiving device is able to translate the message, and

act accordingly. This allows devices to send audio sample memory data, memory dumps, controller settings, and much more. It also allows the

controllers of one device to be controlled by another.

It is not possible to program your own speciﬁed SysEx message into the MK- 425C/449C/461C. However, there are some useful SysEx messages

pre-programmed into the keyboard, that can be accessed by assigning the appropriate MIDI CC to a controller (see Appendix B).

It should be noted that a SysEx message is not transmitted on any speciﬁed channel. All SysEx messages contain a device ID, that is used to single

out devices to respond to the SysEx message. All other devices are ignored. If you are using a SysEx message on the MK-425C/449C/461C, the

global channel is ignored. When you press CHANNEL, instead of entering a channel for the controller, you will be enter a device ID instead. This is

indicated by the fact that the Chan symbol will not be showing.

Device ID’s run from 00 to 127. 127 is the default device number setting on the MK-425C/449C/461C. This setting transmits the SysEx message to

all devices.

Although it is not possible to program the controllers of the MK-425C/449C/461C with your own SysEx messages, there are software applications

that can receive a MIDI input signal and transmit a different, user speciﬁed message. You can program your SysEx messages into the translator

software, then translate the incoming data from the keyboard to your SysEx, depending on the controller you are using.

The Evolution Librarian Software

About The Evolution Librarian Software

The Evolution Librarian Software is a Windows PC librarian program developed for Evolution products. The program not only works with the MK-

425C/449C/461C keyboards but is also compatible with the Evolution UC-33e USB controller. That means you can use one librarian package for

both your keyboard and your controller, if you own a UC-33e.

And even better, you can swap patches between Evolution products that’s supported by the Librarian so you never have to create the same patch

twice.

The librarian itself, allows you to send and receive the 10 patches to and from the MK-425C/449C/461C, load and save memory banks, view how

individual patches have been programmed and drag and drop patches in order to create new combinations in the 10 memory locations.

Evolution MK-425C • MK-449C • MK-461C

English

Installing The Evolution Librarian Software

1. Insert the Evolution Installer CD-ROM in to your CD-ROM drive.

2. Click on “Librarian Installer”

3. Follow the on-screen instructions to complete the installation process.

Once the installation has been completed, launch the program. The following is a screenshot of what you should be seeing on your monitor.

Setting Up The Librarian Software

Before you start using the Librarian, check that the MK-425C/449C/461C has been selected as input and output device.

1. Select MIDI Setup from the Options menu.

2. Ensure the USB driver for you MK-425C/449C/461C is selected in the “Inputs” Column.

If you are using native drivers this may be named “USB Audio Device”.

3. In the “Outputs” column, select the USB driver for you MK-425C/449C/461C

If you are using native drivers this may be named “USB Audio Device”.

You should now be ready to use the Librarian software with you Evolution keyboard.

Librarian Overview

As you can see from the screenshot of the Librarian on page 9, you can save, load, receive or send the complete content to and from either Bank

columns.

To transmit the complete content of your MK-425C/449C/461C to the librarian, simply press the “Receive” button on the Librarian software.

This process can only be completed successfully if the USB drivers for your keyboard have been selected correctly, as described in the “Setting Up

The Librarian Software” section.

Once you have Received data from the keyboard, the memories are displayed in the column.

Organising Presets Received From A Device

You can name the memories as you like. To re-name a memory, double-click on the memory. You can then move memories around by dragging

them to a new position, or using the copy buttons between the two windows.

These buttons are deﬁned below:

Will copy the selected memory in Bank 2 to Bank 1.

Will copy the selected memory in Bank 1 to Bank 2.

Will copy all memories in Bank 2 to Bank 1.

Will copy all the memories in Bank 1 to Bank 2.

Will undo the last copy you made. Only the last copy is remembered.

It’s a good idea to decide which column is your master column, to avoid confusion and maybe loosing hours of work.

Viewing The Contents Of A Memory

Right-click on a memory to view the contents. Please note that it is not possible to edit the contents of a memory. The Sys Ex librarian will simply allow

you to rearrange the order of memories, or copy memories between one dump and another. The screen shot shown below shows the ﬁrst memory

of a memory dump from a 425C with the factory defaults.

Saving A Setup

Once you have named all your presets, and organised them in the desired order, click ’save’ to save the content.

Alternatively you can click on the File menu and select save to save the ﬁle with the previously assigned ﬁle name, or save as to assign the memory

dump a new ﬁle name.

The shortcut key to save is CTRL+S. Make sure you give the ﬁle a name which allows you to quickly identify your collection of setups.

Loading A Setup

To load a memory setup ﬁle back in to the librarian, click on the ’Load’ button and select the required ﬁle. The loaded preset setups will appear in

the Edit Window. You can then either send it directly to the Evolution device by clicking send, or edit it.

Alternatively, select Open from the File menu.

The shortcut key for loading is CTRL+O.

Future Development Of The Librarian

We strongly recommend you register your ownership of the Evolution Librarian if you would like to be kept informed about future development.

As you can see from the version number, the software is at an early version 1.0 stage and we will continue to work on enhancements for the

software.

To register your copy, please visit www.evolution.co.uk/register

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Evolution Elektronische Tastatur Handbücher

Evolution

Evolution EV300 Bedienungsanleitung

Beliebte Elektronische Tastatur Handbücher anderer Marken

Casio

Casio LK-50 Konfigurationshandbuch

Casio

Casio VZ-1 Fehlerbehebungshandbuch

Casio

Casio Privia PX-100 Bedienungsanleitung

Yamaha

Yamaha PortaTone PSR-225GM Bedienungsanleitung

Behringer

Behringer U-CONTROL UMX49 Bedienungsanleitung

Yamaha

Yamaha Portatone X2500 Bedienungsanleitung

Yamaha

Yamaha Portatone PSR-100 Bedienungsanleitung

Casio

Casio WK-1600 Bedienungsanleitung

Keith McMillen Instruments

Keith McMillen Instruments K-Board Pro 4 Technisches Datenblatt

Yamaha

Yamaha PortaSound PCS-30 Bedienungsanleitung

Roland

Roland Juno-6 Bedienungsanleitung

McGrey

McGrey 6170 Bedienungsanleitung

Yamaha

Yamaha PortaTone PSR-41 Bedienungsanleitung

HDC

HDC Kurzweil KP300X Bedienungsanleitung

Casio

Casio Celviano AP-45 Bedienungsanleitung

Akai

Akai MPK88 Bedienungsanleitung

Waldorf

Waldorf IRIDIUM Bedienungsanleitung

Yamaha

Yamaha NP-30 Montageanleitung