Evolution RAGE3+ Bedienungsanleitung

Date Published: 16 / 11 / 2016Original written in UK English

Original Assembly Guide

Read these instructions carefully

Guide d’assemblage d’origine

Lisez attentivement ces instructions

Original-Montageanleitung

Diese Anweisungen sorgfältig lesen.

Guida al montaggio originale

Leggere attentamente queste istruzioni

Montagehandleiding

Gelieve deze handleiding zorgvuldig te lezen

TABLE OF CONTENTS

ITEMS SUPPLIED

BLADE PACKAGING SUMMARY

INSTRUCTIONS

INSTRUCTION MANUAL (Assembly)

INSTRUCTION MANUAL (Operations)

ROTARY BASE AND NECK

CUTTING HEAD (with Moulded Plug)

CARRIAGE SLIDES (colour coded)

BLADE

MITRE LOCKING HANDLE

POSITIVE STOP LOCKING LEVER

HOLD DOWN CLAMP

HEX KEYS(s)

(assembly and blade change)

MARKET SPECIFIC ACCESSORIES

(Not supplied as standard in all markets.

Available as a customer cost optional

accessory. See Operation manual for full

application details)

BLANKING PLUG

(To blank extraction port when cutting Steel)

ADAPTOR TUBE

(For connecting extraction port to

commercial extraction equipment)

LENS CAP

(For laser protection)

Carefully remove all of the parts from the packaging and check that all parts are present

and correct.

 

main parts are colour coded to aid assembly.

Overview of Mitre Saw 03

Tools Needed 04

Watch and Learn 05

Assembly Guide 06

Know the Parts 07

Assembly Procedure 09

 10

Attaching the cutting head 12

Routing the power cable 13

Unlatching & Raising the Cutting Head 14

Fitting the blade 14

Rear support arm 15

Assembly Safety Checks 16

Final Safety Checks 17

www.evolutionpowertools.com

OVERVIEW OF MITRE SAW

1. Dust Bag *

2. On/Off Trigger Switch

3. Blade Guard Release Trigger

(EU Models)/Lock-Off Button

(Canadian Model)

4. Extraction Port

5. Slide Carriage Locking Screw

6. Carriage Slides

7. Laser Guide

8. Bevel Lock Lever

9. Hold Down Clamp

10. Sliding Fence

11. Work piece Support *

12. Mounting Hole (X4)

13. Arbor Lock Button

14. Head Latching Pin

15. Depth Gauge

16. Handle

17. Motor

18. Upper Blade Guard

19. Blade



20. Retractable Lower

Blade Guard

21. Repeat End Stop *

22. Base

23. Table Top

24. Rotary Table

25. Mitre Angle Scale

26. Mitre Locking Handle

27. Positive Stop Locking Lever

*Supplied as original equipment

on the RAGE3+ and RAGE3-S+

and RAGE3-S300.

www.evolutionpowertools.com

TOOLS NEEDED FOR ASSEMBLY & ADJUSTMENTS

SUPPLIED NOT SUPPLIED

6mm Hex Key

(Blade Change)

Flat Bladed

Screwdriver

(See Fig. 9 Page 11)

www.evolutionpowertools.com

DOWNLOAD A FREE QR READER APP

AND SCAN THE QR CODE ABOVE.

INSTANTLY WATCH THE

ASSEMBLY VIDEO ON YOUR SMART PHONE

Make sure the HD setting is on.

QR CODE

You can also view the Assembly Video online located in the

‘Evolution Support Videos’ section at:

www.evolutionpowertools.com/videos/setups/

www.evolutionpowertools.com

ASSEMBLY GUIDE



Your Mitre Saw is supplied as 3 major component parts which

need assembling.

THE ASSEMBLY PROCESS IS A

‘ONE TIME ASSEMBLY’.

Once assembly is successfully completed no attempt to

disassemble the machine should be made. The blade and

some other smaller parts also need to be fitted by the operator.

A safety check must be carried out once assembly is completed

and before the machine is used.

The Cutting Head is supplied with an approved power cable and

plug fitted for its intended country of use.

Do not under any circumstances plug the Cutting Head

into the power supply and try to use it as a hand held

circular saw.

WARNING: Do not connect this machine to the mains power

supply until assembly has been completed and a complete

safety check is carried out.

See Final Safety Checks list on page 17.

www.evolutionpowertools.com

Fig. 1a

RED

WHITE

Fig. 1b

Fig. 1c

KNOW THE PARTS

The 3 main component parts to be assembled are:

 (Fig. 1a)

 (Fig. 1b)

 (Fig. 1c)

www.evolutionpowertools.com

Also to be fitted are:

 (Fig. 2a)

 (Fig. 2b)

  (Fig. 2c)

  (Fig. 2d)

Note: One of two types of Mitre Locking Handle will be

supplied, according to the machine purchased. Only the

short mitre locking handle requires the spacer.

(Fig. 2a) Fit the spacer over the threaded mitre locking

handle before installation. (Short mitre locking handled

machines only)

WARNING: 

be fitted after the assembly process is completed and the mitre

saw has passed the Assembly Safety Checks.

See Assembly Safety Checks list on page 16.

Fig. 2a

Fig. 2b

Fig. 2c Fig. 2d

ANTIVIBRATION SPRING

LONG MITRE

LOCKING

HANDLE

SHORT MITRE

LOCKING HANDLE

SPACER

www.evolutionpowertools.com

ASSEMBLY PROCEDURE

Select the Carriage Slide and Rotary Base and Bevel Neck.

Fitting the Mitre Locking Handle

The threaded rod of the Mitre Locking Handle slides into a

tunnel, or screws into a boss (according to type of machine

purchased) located just above the Positive Stop Locking Lever.

 

Rotary Table Extension.

 

draw the Handle into the locking mechanism. (Fig. 3a)

 

Rotary Table.

Fitting the Positive Stop Locking Lever

The Positive Stop Locking Lever pushes onto the lever

mechanism found just below the Mitre Locking Handle (Fig 3b)

Adjusting the Bevel Neck to 00

The Bevel Neck is supplied fitted to the rotary base and tilted at a 450

angle to the left. Before the carriage slides are inserted into the Bevel

Neck, the Bevel Neck must be adjusted to the vertical position (00).

 (Fig. 4)

 

against the 00stop.

 

Fig. 3a

Fig. 3b

Fig. 4

POSITIVE STOP

LOCKING LEVER

MITRE

LOCKING HANDLE

www.evolutionpowertools.com

INSERTING THE CARRIAGE SLIDE

The Carriage Slides two arms should be inserted into the

two linear bearings in the Bevel Neck. From the BACK of the

machine the red lug should be to the left and the white lug

should be to the right. (Fig. 5)

To aid correct assembly note that the individual arms of the

slide are colour coded, red for the Left Hand arm (as seen from

the back of the machine) and white for the Right Hand arm.

The linear bearings are likewise colour coded.

WARNING: Read steps associated with

Figs 4, 5, 6 and 7 before proceeding.

For accuracy of assembly the two (2) arms of the Carriage Slide

are not the same diameter. Each arm has a dedicated linear

bearing in the Bevel Neck.

Ensure that the Carriage Slide is inserted into the Bevel Neck the

correct way round with the cable clip attachment position on

the back support bracket pointing upwards. (Fig. 6)

 

approximately half of their length.

 

hole in the Bevel Neck, ensuring that the anti-vibration spring

is fitted underneath the hand knob.

Fig. 5

White

Red

BACK VIEWING

Fig. 6

Red

White

www.evolutionpowertools.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Evolution Gesehen Handbücher

Evolution

Evolution EVO355 Raptor Bedienungsanleitung

Evolution

Evolution RAGE Series Bedienungsanleitung

Evolution

Evolution EvoSaw180HD Bedienungsanleitung

Evolution

Evolution Fury 6 Bedienungsanleitung

Evolution

Evolution R210 CMS Bedienungsanleitung

Evolution

Evolution Fury Bedienungsanleitung

Evolution

Evolution R185SMS-Li Bedienungsanleitung

Evolution

Evolution 047-0001 Bedienungsanleitung

Evolution

Evolution RAGE5-S Bedienungsanleitung

Evolution

Evolution RAGE5-S Bedienungsanleitung

Evolution

Evolution FURY5 Bedienungsanleitung

Evolution

Evolution EVOSAW2301 Bedienungsanleitung

Evolution

Evolution FURY5-S Bedienungsanleitung

Evolution

Evolution Rage Twin Bedienungsanleitung

Evolution

Evolution EvoSaw 230 Bedienungsanleitung

Evolution

Evolution Rage 3-S 300 Bedienungsanleitung

Evolution

Evolution F255 SMS Bedienungsanleitung

Evolution

Evolution Fury 3 Bedienungsanleitung

Evolution

Evolution EVOSAW 185 Bedienungsanleitung

Evolution

Evolution EVO180 V2 Bedienungsanleitung

Evolution

Evolution R165 CCSL Bedienungsanleitung

Evolution

Evolution 230-HDX Bedienungsanleitung

Evolution

Evolution Fury3-B Betriebsanleitung

Evolution

Evolution F165CCSL Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung