Evotools MT 300 Bedienungsanleitung

MANUAL DE UTILIZARE / USER’S MANUAL

UNEALTA MULTIFUNCTIONALA / MULTI TOOLS

MT 300

www.honest.ro

RO_________________________________________________

Va multumim pentru achizitionarea acestui produs EVOTOOLS, fabricat

conform celor mai inalte standarde de siguranta si de functionare.

Avertizare! Pentru siguranta dumneavoastra cititi cu atentie acest manual

si instructiunile generale de siguranta inaintea utilizarii echipamentului.

Nerespectarea acestor reguli poate avea ca rezultat producerea

electrocutarilor, a incendiilor si/sau a ranirilor personale.

Simboluri

Simbolurile utilizate in manual sau pe produs au urmatoarele semnificatii:

Masuri de siguranta generale pentru uneltele electrice

Zona de lucru

Pastrati zona de lucru curata si bine iluminata.Umiditatea si zonele intunecate pot crea

accidente

Nu utilizati unealta in zonele cu potential exploziv, de exemplu in prezenta lichidelor, gazelor

sau particulelor inflamabile. Uneltele electrice genereaza scantei care pot aprinde aceste

materiale.

Nu lasati copii sau persoanele neautorizate in zona de lucru. Distragerea atentiei poate

cauza pierderea controlului uneltei.

Masuri de siguranta a echipamentului in exploatare

ATENTIE! Verificati intotdeauna ca tensiunea de alimentare sa corespunda cu cea

inscrisa pe placuta produsuui.

Nu rasuciti cablul electric de alimentare al uneltei

Nu transportati unealta tinand-o de cablul electric si nu trageti de cablul electric pentru a o

scoate din priza.

Tineti cablul electric de alimentare al uneltei la distanta fata de sursele de caldura, de petele

de ulei, de grasimi, de obiectele ascutite si sursele care emana caldura.

Verificati stecherul si cablul electric in mod regulat si in caz de deteriorare a acestora apelati

la un electrician autorizat.

Evitati pornirile accidentale ale uneltei. Asigurati-va ca intrerupatorul este in pozitia “Oprit”

inainte de introducerea cablului de alimentare in priza.

Nu utilizati unealta in conditii de ploaie sau umiditate excesiva. Patrunderea apei in interiorul

uneltei creste riscul unui scurtcircuit.

Pentru utilizare in aer liber, folosiți cabluri de prelungire care sunt atestate și marcate în mod

corespunzător pentru utilizarea in mediul exterior.

Nu suprasolicitati unealta electrica! Masina poate fi folosita in conditii de siguranta daca sunt

respectati parametrii de exploatare care o caracterizeaza. Nu utilizati unelte electrice cu un alt

scop fata de cel pentru care sunt destinate.

Masuri de siguranta personala

Intotdeauna utilizati o imbracaminte adecvata.Nu purtati haine largi sau bijuterii. Daca aveti

parul lung, acestatrebuie legat. Apare riscul prinderii acestora de catre partile componente ale

masinii aflate in miscare.

Utilizati intotdeauna ochelari de protectie iar atunci cand lucrati in mediul exterior va

recomandam sa utilizati manusi si bocanci de protectie.

Intotdeauna folositi o masca de praf atunci cand in procesul de prelucrare se produce praf.

Daca exista posibilitatea de instalare a dispozitivelor de evacuare a prafului atunci asigurati-

va ca acestea sunt conectate si utilizate corect.

Service

Repararea trebuie realizata numai de catre personal autorizat prin inlocuirea cu accesorii si

piese de schimb originale pentru a se evita producerea accidentelor datorate reparatiilor

necorespunzatoare.

Masuri de siguranta specifice uneltei multifunctionale

Tineti unealta numai de partile izolate, la efectuarea unei operatii in care accesoriul de lucru

poate intra in contact cu cabluri ascunse sau cu propriul cablu de alimentare.

Inainte de utilizare, verificati ca accesoriile sa nu fie deteriorate. Nu folositi accesorii fisurate,

rupte sau deteriorate.

Asigurati-va ca accesoriile au fost montate si fixate corect. Nu folositi saibe reductoare sau

adaptoare pentru a face ca accesoriile sa intre corespunzator.

Unealta mutifunctionala este dublu izolata. Aceasta inseamna ca este prevazuta cu doua tipuri

complet independente de izolatie care impiedica operatorul sa intre in contact direct cu partile

metalice ale cablurilor. Această măsură reprezintă un grad ridicat de protectie împotriva

electrocutarilor.

Domeniu de utilizare

Unealta multifunctionala este destinata uzului personal pentru operatiile de debitare, taiere ,slefuire

a diverselor materiale, in combinatie cu accesoriile corecte.

NU ESTE PROIECTAT PENTRU UZ INDUSTRIAL.

Parti componente (fig 1) Accesorii

1. Intrerupator Pornit/Oprit Panza semicirculara

2. Variator frecventa oscilatii Panza dreapta

3. Suport cheie hexagonala Razuitor rigid

4. Fante ventilatie Hartie abraziva

5. Cap fixare accesorii Suport hartie abraziva

Cheie hexagonala

Pregatirea pentru punerea in functiune

Montare/inlocuire accesorii

Panza ferastrau semicirculara / dreapta (fig 2)

Cu ajutorul cheii hexagonale (1) indepartati surubul(2) si saiba (3) de capul de fixare al

accesoriilor (6)

Introduceti panza (4) astfel:

oAsigurati-va ca perforatiile (5) din lama sunt aliniate cu pinii (6)din capul de fixare iar

fata inscriptionata a accesoriului este pozitionata spre unealta.

oPanza poate fi pozitionata spre dreapta/stanga sau centrata in functie de necesitati

oAplicati saiba peste panza , avand grija ca partea ei convexa sa fie pozitionata spre

unealta si strangeti surubul in capul de fixare.

Hartie abraziva (fig 3)

Instalati placa speciala (1) pe unealta.

Apasati ferm hartia abraziva (2) pe placa suport, avand grija sa aliniati perforatiile din hartie cu

cele din placa

Pentru a o inlocui , desprindeti-o din suport prin simpla tragere.

Operatiune

Accesoriu

Setare frecventa oscilatiii

Gips carton

Panza semicirculara

Maximum

Reparatii ferestre lemn

Panza semicirculara

Mediu

Toc usa

Panza dreapta

Max / mediu

Dibluri lemn

Panza dreapta

Maximum

Teava PVC

Panza dreapta

Mediu

Linoleum

Razuitor

Mediu

Slefuire

Hartie abraziva

Max / mediu

Utilizare

ATENTIE! IN CAZUL IN CARE APAR ZGOMOTE ANORMALE IN FUNCTIONARE

OPRITI IMEDIAT UNEALTA SI ADRESATI-VA UNUI SERVICE AUTORIZAT PENTRU

CONSTATARI SI REPARATII.

Pornire /oprire

Pentru pornirea uneltei apasati comutatorul (1) spre capul de fixare.Pentru oprire culisati-l spre

partea din spate

Reglare frecventa oscilatii

Aceasta unealta opereaza la o frecventa intre 10000 si 18000 OPM. Pentru cresterea frecventei

rotiti variatorul spre stanga (MAX) sau in sens invers pentru scaderea frecventei (#1).Setarea

optima tine cont de tipul de accesoriu utilizat, de suprafata de prelucrat si de complexitatea

proiectului.

Decupare toc usa pentru montare parchet (fig 4)

Instalati accesoriul (3) pentru decupat lemn in unealta.

ATENTIE: panza trebuie pozitionata central pe unealta, NU la 90°.

Plasati o bucata de parchet (1) la cca 25 mm de toc (2) si sprijiniti lama uneltei de ea, fara ca

dintii taietori sa atinga zona de prelucrat (4)

Setati frecventa la maxim, porniti unealta si incepeti prelucrarea prin glisarea usoara a lamei

(3) pe placa de parchet spre toc.Nu exercitati o presiune prea mare pe unealta pentru evitarea

aparitiei oscilatiilor.

Decupare perete gips- carton pentru instalare doze electrice (fig 5)

Instalati panza semicirculara (2) in unealta

ATENTIE: panza trebuie pozitionata central pe unealta, NU la 90°.

Asezati corpul dozei in pozitia dorita si trasati-i conturul pe perete (1).

Pozitionati marginea panzei perpendicular pe perete, la mijlocul uneia dintre laturile marcate

pentru taiere.

Setati frecventa la maxim, porniti unealta si taiati pana in coltul dreptunghiului marcat.Nu

exercitati o presiune prea mare pe unealta pentru evitarea aparitiei vibratiilor.

Opriti unealta , pozitionati-o in directie opusa si completati taierea primei laturi.

Repetati pasii de mai sus pentru a taia si celelalte 3 laturi.

La terminarea operatiunii, utilizati o surubelnita plata pentru a extrage partea decupata din

perete. NU utilizati lama uneltei in acest scop intrucat se poate rupe.

Slefuire fina

Instalati placa de slefuit in unealta si aplicati pe ea hartia abraziva cu granulatia

corespunzatoare tipului de finisare dorit.

Setati oscilatiile intre nivelul 4 si Max

Porniti unealta si incepeti slefuirea prin glisarea uneltei pe suprafata de prelucrat.

Razuire

Instalati accesoriul pentru razuire in unealta.

Setati oscilatiile intre nivelul 4 si Max

Porniti unealta si incepeti prelucrarea prin introducerea lamei sub materialul care trebuie

indepartat. Ridicati usor unealta din partea din spate astfel incat sa se formeze un mic unghi

intre cele 2 materiale pentru facilitarea desprinderii lor.

Curatare si intretinere

ATENTIE! Inainte de orice interventie asupra echipamentului, deconectati

alimentarea cu energie electrica de la retea.

Curatare

Pastrati curate fantele de ventilatie ale carcasei pentru a preveni supraincalzirea motorului

Regulat, de preferat dupa fiecare utilizare curatati echipamentul cu o carpa moale.Daca

murdaria persista, utilizati o carpa umezita intr-o solutie de apa si sapun

NU utilizati solventi (ca de exemplu : petrol si derivati, alcool) intrucat acestia pot deteriora

partile din plastic.

Intretinere

Echipamentul nostru a fost proiectat astfel incat sa poata fi utilizat pentru o perioada indelungata cu

un minimum de intretinere.Veti putea obtine intotdeauna o satisfactie maxima in timpul utilizarii

respectand indicatiile de mai sus.

Date tehnice

Tensiune / Frecventa

230-240V ~ 50Hz

Putere nominala

300W

Frecventa variabila oscilatii

10.000 -18.500 / min

Depozitare

Intotdeauna inainte de depozitarea uneltei curatati carcasa ei cu o carpa putin umezita in apa

cu sapun.

Depozitati unealta electrica intr-un spatiu inaccesibil copiilor intr-o pozitie stabila si sigura intr-

un loc racoros si uscat, evitand temperaturile prea ridicate sau scazute.

Protejati unealta electrica fata de actiunea directa a razelor solare si pastrati-o intr-un loc

intunecos, daca este posibil.

Nu pastrati masina ambalata in folie sau in punga de plastic pentru a evita acumularea

umiditatii.

Garantie

Garantia acopera toate materialele componente si viciile de fabricatie cu exceptia,fara insa a fi

limitate la:

Baterii, incarcatoare, componente uzate ca urmare a unei exploatari normale (perii

colectoare, rulmenti, cabluri, etc) sau accesorii (burghie, biti, dalti etc..),

Defecte cauzate de o exploatare, intretinere si depozitare necorespunzatoare, modificari

neautorizate asupra echipamentului, costul transportului.

Pagube materiale si leziuni corporale rezultate in urma exploatarii necorespunzatoare a

echipamentului.

Deteriorari cauzate de lichide,patrundere excesiva de praf, distrugere intentionata , utilizare

inadecvata (pentru scopuri in care acest echipament nu este proiectat), etc.

EN_________________________________________________

Thank you for buying this EVOTOOLS product, manufactured according

to the highest safety and performance standards

WARNING! For your own safety, read this manual and the general safety

Instructions carefullybefore using the appliance. Your power tool should only be

given to other users together with these instructions.

Symbols

In this manual and/or on the machine the following symbols are used:

General power tools safety warnings

Working area

Keep working area clean and well lit. Untidy and dark areas can lead to accidents.

Do not operate power tools in potentially explosive surroundings, for example, in the

presence of inflammable liquids, gases or dust. Power tools create sparks which may

ignite the dust or fumes.

Keep children and bystanders at a distance when operating a power tool. Distractions can

cause you to lose control of it.

Electrical safety

Always check that the power supply corresponds to the voltage on the rating plate.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

Personal safety

Use safety equipment. Always wear eye protection. Using safety equipment such as a

dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed

will reduce the risk of personal injury.

Avoid accidental starts. Ensure the switch is in the off position before inserting the plug.

Carrying power tools with your finger on the switch or plugging in power tools when the

switch is in the on position makes accidents more likely.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from the power tool. Loose clothes, jewellery or long hair can become

entangled in the moving parts.

Service

Your power tool should be serviced by a qualified specialist using only standard spare parts. This

will ensure that it meets the required safety standards.

Specific safety instructions for multi tool

Hold the tool only from insulated parts, to avoid electrical shock when accidentaly contact

with hidden wiring or its own cord occur

Before use, check that the accesories are not damaged. Do not use accesories cracked,

broken or damaged.

Make sure that the accesories was fitted and secured properly. Do not use washers reducers

or adapters to make the accesories fixing properly.

Multi tools is double insulated. This means it has two completely independent types of

insulation that prevents the operator to enter into direct contact with the metal parts of the

cables. This measure is a high degree of protection against electrocution.

Application

This multi tool is intended for personal use for grinding and polishing of different materials, in

combination with the correct accessories.IT IS NOT DESIGNED FOR PROFFESIONAL USE.

Description (fig1) Accesories

1. ON/OFF switch Semicircular blade

2. Speed control wheel Straight blade

3. Hex key holder Scraper

4. Ventilation slots Sanding pad

5.Accesory holder Sanding paper

Hex Key

Assembly

Disconnect the power plug before carrying out any adjustments or maintenance.

Installing/replacing accessories

Blade (fig 2)

Using the hex key (1) ,remove the screw(2) and the washer(3) from the accesory holder

Place the blade (4) onto the accesory holder as follows:

oMake sure that the alignment holes (5) in the blade fit over the alignment pins (6) in

the accesory holder and the printed side of the blade is facing the tool.

oThe blade can be mounted at various angles left/ right or center if required.

oPut the washer with the convex side facing the tool and tight with screw.

Sandpaper (fig 3)

Install the hook and loop sanding pad (1) onto the tool

Firmly press the sandpaper (2) onto the pad, so the holes in the sandpaper line up with the

matching holes in the pad

To remove the sandpaper, simply peel it from the pad.

Project

Accesory

Speed

Drywall

Half circle blade

Maximum

Restoring windows

Half circle blade

Medium

Door casing

Straight blade

Max / medium

Dibluri lemn

Straight blade

Maximum

PVC Pipe

Straight blade

Medium

Glued flooring

Scraper

Medium

Sanding

Sander

Max / medium

Operation

WARNING! IN case of any abnormal noise, immediately turn off the tool and

contact an authorized service facility for repairs

Switching ON and OFF

Connect the tool to the power supply.

To start the machine, you push forward the ON / OFF switch (1). To stop the machine, you push

backward the ON / OFF switch.

Speed control wheel

The tool could run at speed between 10000 and 18000 OPMby rotating the speed control wheel

(2) to left to increase the speed (MAX) or to right to decrease the speed (#1).The optimal speed

will vary depending upon the type of accesory, surface being worked and the complexity of project

Flush cutting a door jamb (fig4)

Install the cutting blade (3) into the tool

NOTE: the blade should be centered on the tool housing, NOT installed in 90° position.

Place a scrap piece of a floor tile (1) on the floor, about 25 mm from the jamb (2)., and place

the tool lightly touching the surface of the tile and the cutting teeth NOT touching the surface

to be cut (4)

Set the the speed to the fast position, turn the tool ON, and start plunge the blade onto the

door jamb while sliding the blade along the floor tile.Do not put too much forward pressure on

the saw blade as to avod the excessive vibrations.

Cutting a hole in a drywall to install an electrical outlet box (fig 5)

Install the half-circle cutting blade (3) into the tool

NOTE: the blade should be centered on the tool housing, NOT installed in the 90° position.

Place the putlet box on the drywall and trace the required rectangular hole (1)

Place the corner edge of the saw blade (2) , near the wall in the middlle of one of the cutting

lines.

Set the speed to the MAX ,turn ON the tool and start cutting to the corner of the rectangle.

Do not put too much forward pressure on the saw blade as to avod the excessive vibrations.

Turn the saw OFF and proceed to cut in the opposite direction to complete the cut for the first

side of rectangle.

Repeat the steps above to cut the remaining three sides of rectangle.

At the end use a flat blade screw to carefully pry the cut-out from the wall.Do not use the tool

blade as to avoid blade damage.

Detail sanding

Install the sanding pad on the tool and fix the desired sandpaper on it

Set speed between level 4 and MAX

Put the tool ON and start sanding by sliding the tool ove the workpiece.

Scraper blade

Install the scraper on the tool and set speed between level 4 and MAX

Put the tool On and start working by place the blade under the material to be removed.Lift

the tool from the rear side as to form a very slight angle with the workpiece

Cleaning and maintenance

Before performing any work on the equipment, pull the power plug.

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the engine.

Regularly clean the machine housing with a soft cloth, preferably after each use.If the dirt

does not come off use a soft cloth moistened with soapy water.

Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

Maintenance

Our machines have been designed to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon proper machine care and regular

cleaning.

Technical data

Voltage/ Frequency

230-240V ~ 50Hz

Input power

300W

Variable speed

10.000 –18.500 /min

Storage

Thoroughly clean the whole machine and its accessories.

Store it out of the reach of children, in a stable and secure position, in a cool and dry

place, avoid too high and too low temperatures.

Protect it from exposure to direct sunlight. Keep it in the dark, if possible.

Don’t keep it in plastic bags to avoid humidity build-up.

Warranty

This warranty covers all material or production flaws excluding:

Batteries, chargers,defective parts subject to normal wear & tear such as bearings, brushes,

cables, and plugs, or accessories such as drills, drill bits, saw blades, etc. ;

Damage or defects resulting from maltreatment, accidents or alterations; nor the cost

transportation.

We also disclaim all liability for any bodily injury resulting from inappropriate use of tool.

Definitely excluded from the warranty is damage resulting from fluid permeation, excessive

dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate

usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not

following the instructions given in the manual), inexpert assembly, lightning strike, erroneus

net voltage. This list is not exhaustive.

Inhaltsverzeichnis

Sprachen:

Andere Evotools Elektrowerkzeuge Handbücher

Evotools

Evotools EN 500 Bedienungsanleitung

Evotools

Evotools CM-1.1B Bedienungsanleitung

Evotools

Evotools HG2000E EPTO Bedienungsanleitung

Evotools

Evotools HG2000 Bedienungsanleitung

Evotools

Evotools EP 650 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch