Exadigm NX2200e Bedienungsanleitung

NX2200e User Guide

Printed in USA

Warranty

The information contained in this document is subject to change without notice.

ExaDigm makes no warranty of any kind with regard to this material, including, but not limited to, the

implied warranties or merchantability and fitness for a particular purpose.

ExaDigm shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

Documentation

All documentation is located at www.exadigm.com and is subject to change.

NX2200e User Guide

Table of Contents

1.0 NX2200e Handheld Mobile Terminal ..........................................................4

2.0 Accessories, Parts and Peripherals ............................................................4

3.0 Installing the NX2200e................................................................................4

4.0 Terminal Components.................................................................................5

4.1 Front View..........................................................................................5

4.2 Terminal Ports ............................................................................................5

4.3 Top View.....................................................................................................5

5.0 Installing a Paper Roll.................................................................................6

6.0 Installing and Removing the Battery Pack...................................................6

7.0 SIM Chip Installation...................................................................................7

8.0 Powering Terminal......................................................................................8

9.0 Card Swipe.................................................................................................8

9.1 NFC ...................................................................................................8

10.0 Modem Configurations................................................................................8

10.1 CDMA ................................................................................................8

10.2 HSPA.................................................................................................8

10.3 Ethernet .............................................................................................8

10.4 WiFi....................................................................................................8

11.0 Alpha/Numeric Keypad...............................................................................9

11.1 QWERTY Keyboard...........................................................................9

12.0 Color-Coded Keys.....................................................................................10

12.1 Special Function Keys......................................................................10

13.0 Terminal Indicators ...................................................................................10

14.0 Terminal Functions ...................................................................................11

14.1 View Transactions............................................................................11

14.2 Hot Keys ..........................................................................................12

15.0 Security Manager......................................................................................12

15.1 Managing User.................................................................................13

15.2 User Passwords...............................................................................14

15.3 User Rules.......................................................................................14

16.0 Data Retention..........................................................................................14

16.1 Security Features.............................................................................15

17.0 Battery and Charger Safety.......................................................................16

18.0 Regulatory Notices and Certifications .......................................................17

NX2200e User Guide

18.1 Part 15 of FCC Rules.......................................................................17

18.2 Part 68 of FCC Rules.......................................................................17

18.3 SAR Labeling...................................................................................18

18.4 UL Standards...................................................................................18

NX2200e User Guide

1.0 NX2200e Handheld Mobile Terminal

The ExaDigm NX2200e terminal supports multiple applications and will communicate with the host via

Ethernet, Cellular Modem CDMA or GSM/GPRS and WiFi.

NX2200e features include:

2.0 Accessories, Parts and Peripherals

Shipped items include:

3.0 Installing the NX2200e

When installing the ExaDigm NX2200e for countertop, use a location near a power outlet and Ethernet

connectivity if using this option. Carefully plug the AC adapter into the terminal (the plug should insert into

the power receptacle on the left side of the terminal) and secure it to a live electrical outlet.

The battery time will vary according to the terminal setup and merchants‟usage.

Certain conditions may damage the terminal or cause it to operate poorly. In general, avoid areas with:

Excessive heat or dust

Oil or moisture

Excessive electrical noise (caused by air conditioners, motors, fans, neon signs, or power tools)

Direct sunlight

Artificial light that could reflect glare off the display panel

PCI information:

PCI PA-DSS 3.0 approved payment

applications

PCI PTS 4.0 approved

EMV Level 1 and 2 approved

Modem versions:

CDMA Verizon or Sprint

HSPA

Integrated 2D Bar Code Reader*

Smart Card Reader

SAM Card Reader

5MP resolution camera*

SD Card Reader

Capacitive Touch Screen

Integrated Contactless Card Reader

*special order terminals

NX2200e unit

Power adapter (8.5V)

Lithium-ion Battery

Small paper roll (thermal 2 ¼ x 1.38”)

NX2200e User Guide

4.0 Terminal Components

4.1 Front View

4.2 Terminal Ports

4.3 Top View

LED Lights

Magnetic Card Reader

Screen

Power ON/OFF

Up/Down Arrow

Cancel Key

2 Programmable Function Keys

Clear/Backspace Key

Enter Key

Smart Card Reader

Power

USB Port

Ethernet

RS-232

Feed Key

The figure to the right shows the ports used to

connect the terminal to a power source,

Ethernet port and various devices such as PIN

pads using the multi-port connector.

Mini USB

Barcode Reader

Camera

NX2200e User Guide

5.0 Installing a Paper Roll

A paper roll is required to print receipts and reports. The NX2200e uses thermal 2 ¼ x 1.38” paper rolls.

1.Place forefinger under flap at the bottom of the terminal and pull forward using force.

2.Using the tab lift compartment out.

3.Place the paper roll in the printer compartment.

4.Close the printer compartment door by pressing until it clicks into place.

6.0 Installing and Removing the Battery Pack

The power pack allows the terminal to operate when not connected to a power outlet. The NX2200e uses

a Lithium-ion battery. Average battery life is 12 hours (utilizing power saving features).

1.Remove the screw securing the battery door using a Phillips head screwdriver. Remove the battery

door by placing your finger on the door, push down on the ridges and slide down to remove.

2.Remove the battery by placing a finger on the opening and pulling up. The battery will loosen and fall

out once the terminal is turned over.

3.To install slide the battery under the locking tabs and push down.

4.Replace the battery door by inserting the top hedge in first, slide up until it snaps into place.

NX2200e User Guide

7.0 SIM Chip Installation

Note: SIM chips are only used in HSPA equipped terminals. The SIM chip slot is located with the

terminal face down under the battery compartment. Unscrew the screw located on the top of the battery

cover. The battery cover can be removed by placing your finger on the raised portion of the door and

sliding down to remove.

1.Remove the battery by placing a finger on the opening and pulling up. The battery will loosen and fall

out once the terminal is turned over.

2.There is only one working compartment be sure to use the one located on the bottom left side.

3.The SIM chip can be easily placed into the slot by inserting the card into the grooves of the holder.

The metallic contact on the SIM card must be placed face down (toward the contacts on the unit).

NX2200e User Guide

8.0 Powering Terminal

9.0 Card Entry

Insert Smart Card into the reader slot below key pad.

9.1 NFC

10.0 Modem Configurations

Ensure that the terminal is connected to an active power source or has a fully charged battery in it.

10.1 CDMA

Before you use the terminal to do live transactions with TCP/IP connections, you need to make sure the

modem is activated. Contact your network carrier, ISO or ExaDigm to confirm activation.

10.2 HSPA

Before you use the terminal to do live transactions with TCP/IP connections, you need to make sure the

modem is activated by inserting the SIM card. Contact your network carrier, ISO or ExaDigm to confirm

activation.

10.3 Ethernet

Connect the Ethernet cable to the Ethernet port (LAN) on the side of the terminal.

10.4 WiFi

Connect the WiFi USB stick to the USB port on the side of the NX2200e.

Swipe card through reader with the magnetic stripe

facing down and toward the terminal.

To power on terminal press orange Power key

until beep is heard. The boot up process will

display.

To power down terminal press orange Power

key briefly then press ENTER to complete

process.

Press [ENTER] key to

power off!!

Other keys to cancel.

Gently place the NFC Card above the screen or

slowly swipe across toward the keypad.

NX2200e User Guide

11.0 Alpha/Numeric Keypad

To get a letter, press the corresponding

number and then continue pressing until the

letter is displayed.

Number

Alpha 1

Alpha 2

Alpha 3

Alpha 4

Alpha 5

Alpha 6

SPACE

„

“

(

)

{

}

[

]

;

11.1 QWERTY Keyboard

To input capital letters press the up arrow []and press the key.

To input symbols press the [?123] key on the touch screen; the number and symbol screen will display.

Press the [ALT] key for additional characters.

To backspace and clear characters use the [DEL X] key or [CLEAR] on the keypad.

NX2200e User Guide

For numeric only entry menus the following keypad will display:

12.0 Color-Coded Keys

The color-coded keys perform the following tasks:

Red CANCEL Key: Press the red key to cancel the current operation or return to the previous menu.

Yellow CLEAR Key: Press this key to clear an action and backspace clearing each character.

Green ENTER Key: This key is used like the ENTER key on a computer keyboard. Press the green

key to signify to the terminal that the task is complete, or press to enable a function or perform an

action based on typed data.

Red Power Key: Press this key to turn on or off the terminal.

12.1 Special Function Keys

F1: This key will move the cursor to the left of a text character.

F2: This key will move the cursor to the right of a text character.

Red Power Key plus:

7: This will advance to the next application slot.

9: This will revert to the previous application slot.

F1: This will advance to the next populated application slot.

F2: This will revert to the previous populated application slot.

13.0 Terminal Indicators

Indicators are located on the display screen and will display when the mentioned peripheral or device is

attached.

Battery

Fully charged

Half full battery

Low battery

Ethernet connection ˂----˃

Power Adapter

Radio

WiFi signal strength

Cellular signal strength

Inhaltsverzeichnis

Andere Exadigm Handheld Handbücher

Exadigm

Exadigm NX2200 Series Bedienungsanleitung

Beliebte Handheld Handbücher anderer Marken

Honeywell

Honeywell Dolphin 9900 Bedienungsanleitung

Honeywell

Honeywell CN75 Bedienungsanleitung

MiTAC

MiTAC Mio 168 Bedienungsanleitung

Wasp

Wasp WDT92 Bedienungsanleitung

Texas Instruments

Texas Instruments TI-Nspire Bedienungsanleitung

AXEM Technology

AXEM Technology MBS Bedienungsanleitung

Armstrong

Armstrong Brain Wave Montageanleitung

Unitech

Unitech TB128 Bedienungsanleitung

Symbol

Symbol MC9000-G Installations- und Betriebshandbuch

Unitech

Unitech HT1 1D Batch Bedienungsanleitung

Ingenico

Ingenico IWL220 GPRS Bedienungsanleitung

Intermec

Intermec CK61 Bedienungsanleitung

Symbol

Symbol c2000 Bedienungsanleitung

Symbol

Symbol MC18 Installations- und Betriebshandbuch

Acer

Acer n20 Bedienungsanleitung

Intermec

Intermec CK61 Bedienungsanleitung

Docomo

Docomo F-04H Bedienungsanleitung

Toshiba

Toshiba e350 Series Bedienungsanleitung