EXMITTER EX7 Bedienungsanleitung

EXMITTER -- Professional Remote Control Products Expert

2
EXMITTER EX6 Digital Radio System
The following terms are used throughout the product literature to indicate various
levels of potential harm when operating this product.
CAUTION: Procedures, which if not be properly followed, is able to create a possibility
of physical property damage AND or possibility of injury.
Read the ENTIRE instruction manual to become familiar with the features of the
product before operating. Fail to operate the product correctly can result in damage
to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with
caution and common sense and requires some basic mechanical ability. Fail to operate
this Product in a safe and responsible manner could result in injury or damage to the
product or other property. This product is not intended for use by children without direct
adult supervision. Do not attempt to disassemble, use with incompatible components
or augment product in any way without the approval of VolantexRC Co., Ltd..
This manual contains instructions for safety, operation and maintenance. It is essential
to read and follow all the instructions and warnings in the manual, prior to assembly,
setup or use, in order to operate correctly and avoid damage or serious injury.
WARNING
• Always ensure all batteries have been properly charged prior to using the model.
• Always check all servos and their connections prior to each run.
• Never operate your model near spectators, parking areas or any other area that could
result in injury to people or damage of property.
• Never operate your model during adverse weather conditions. Poor visibility can
cause disorientation and loss of control of your model.
• Never point the transmitter antenna directly toward the model. The radiation pattern
from the tip of the antenna is inherently low.
• If at any time during the operation of your model you observe any erratic or abnormal
operation, immediately stop operation of your model until the cause of the problem has
been ascertained and corrected.
Safety Precautions

3
EXMITTER EX6 Digital Radio System
Channel 6
Rudder Trim
Dual Rate Function
Indicator LED
Throttle Trim
3-Switch Channel 5
ON/OFF Switch
Aileron Trim
Elevator Trim
Transmitter Details
Menu/Enter
Back Down
Up
Rudder Trim
Throttle Trim
Aileron Trim
Elevator Trim
MODE 2
MODE 1
Throttle
Rudder
Elevator
Aileron
Elevator
Rudder
Throttle
Aileron
Channel 7 Knob

4
EXMITTER EX6 Digital Radio System
Remove the battery cover and install
4 AA batteries. Make sure the polarity
of each corresponds with the diagram
in the battery holder. Replace the
battery cover.
Install Batteries
EX7 uses one-button ON/OFF
switcher. Press the button for 1
second to turn on the transmitter
; Press and hold the button for 2
second to turn off the transmitter.
One-Button ON/OFF Switch
When the battery voltage drops below
4.3 volts, an alarm will sound and the
voltage LEDs will ash.
Low Voltage Alarm Retreatable Antenna
The EX6 comes with a retreatable
antenna. When transporting, you can
rotate it down at rear place to save
space.

5
EXMITTER EX6 Digital Radio System
ELECTRONIC
SPEED CONTROL
CAUTION: Do not cut the antenna.
Install Your Receiver
Binding is the process of programming the receiver to recognize the GUID (Globally
Unique Identifier) code of a single specific transmitter. When a receiver is bound to
a transmitter, the receiver will only respond to that specic transmitter. If you need to
rebind for any reason, please follow these steps:
1. With the transmitter switched ON
2. Power on the receiver,then press the bind button in 3 seconds.
3. Loose the bind button and wait for about 5 seconds.
4. The receiver LED will keep ashing, means it is binding.
5. After the receiver LED stop ashing, it means the binding is done.
Receiver Connection & Binding
Bind Button
Antenna
Channels Instruction
RECEIVER
BATTERY
SERVO
STEERING SERVO
GAS INSTALLATION THROTTLE SERVO
RECEIVER
BEC BATTERY
Failsafe Setting
The EX7 comes with the receiver failsafe set to NONE. In the event of loss of signal
the motor will stop and the vehicle will willdrift. If the signal is regained normal function
will return. If you wish to program the failsafe to a custom setting, just follow these
simple steps:
1. While binding(LED flashing), keep sticks at position that you want the vehicle to
stay when failsafe
2. When binding done(LED stop ashing), the system will remember the position you
set for failsafe.
ELECTRICAL INSTALLATION

6
EXMITTER EX6 Digital Radio System
D/R Setting
D/R function allows you to adjust the travel volume of channels, its volume is based on
Endpoint function.
The D/R function includes two preset position "1" and "0". When you switch D/R
channel to position 0, your travel adjustment is based on 100% volume. When you
switch D/R channel to position 1, your travel adjustment is based on 50% volume.
The D/R function setting is based on the current model. When you set D/R under Model
No.1, the setting will only work under Model No.1.
Channel Reverse
Channel reserve function allows you to
reserve any of the 7 channels.
The reserve function setting is based
on the current model. When you set
reserve under Model No.1, the setting
will only work under Model No.1.
Menu Functions
NOTICE: After you nish setting of D/R and return back to main menu, next time when
you enter D/R function setting, it will remember the setting status you saved last time.
The EX7 comes with a digital LCD screen
displaying a 3-level menu.
Press Menu button to turn on/off
background light of the screen.
Following below instructions you are able
to operate settings to EX7.

7
EXMITTER EX6 Digital Radio System
Endpoint function allows to adjust max travel volume from -140% to 0%, 0% to 140%.
Endpoint setting works on Channel THRO, AILE, ELEV, RUDD, GEAR, AUX1, AUX2.
When you set endpoint volume smaller than sticker volume, the travel volume of the
particular channel will be adjusted according to the smaller endpoint. For example, if
you set max endpoint to +10%, when the sticker moves to +50%, the actual volume will
be only +5%.
It is the same case when you set endpoint volume higher than sticker volume, shown
as above illustration at right side.
The setting is based on the current model. When you set D/R under Model No.1, the
setting will only work under Model No.1.
NOTICE: After you nish setting and return back to main menu, next time when you
enter reserve function setting, it will remember the setting status you saved last time.
Endpoint Setting
NOTICE: After you nish setting of endpoint and return back to main menu, next time
when you enter endpoint function setting, it will remember the setting status you saved
last time.
Sub-Trim
Sub-trim function allows to adjust channel servo travel center point from -30% to +30%.
Sub-trim can be accumulated with trimming by adjusting trim buttons on transmitter.
Trim Buttons

8
EXMITTER EX6 Digital Radio System
The EX7 comes with digital trims. Each time a trimmer is moved the servo output will
change one step. If the trimmer is held, the output will scroll in that direction until the
trimmer is released or the output reaches its end.
Digital Trims
Throttle
Trim
Throttle
Trim
Rudder
Trim
Rudder
Trim
Elevator
Trim
Elevator
Trim
Aileron
Trim
Aileron
Trim
Mode 2
CAUTION: Do not use too much sub-trim otherwise you may damage the servo.
NOTICE: After you nish setting of endpoint and return back to main menu, next time
when you enter endpoint function setting, it will remember the setting status you saved
last time.
Mode 1
Mixing Modes
Mixing modes allow you to mix several channels to be controlled together, changing
one channel to be a new functional channel.
EX7 comes with 3 different preset mixing modes. Follow below steps to set each
mode.
DUALAILE mixes channel 2 and channel 6. When controlling channel 2, channel 6 will
relatively react. Channel 2 only reacts to movement of stick, endpoint setting and sub-
trim setting. When you adjust endpoint or sub-trim setting of channel 2, it will apply to
channel 6 too.
ELEVON mixes channel 2 and channel 3. When controlling one channel, the other
one channel will relatively react.
V-TAIL mixes channel 3 and channel 4. When controlling one channel, the other one
channel will relatively react.

9
EXMITTER EX6 Digital Radio System
NOTICE: In mixing mode, reverse function is still individual for each channel. If you
need for reverse setting, you need to set it individually on channel 2 and channel 6 with
different direction
NOTICE: In mixing mode, adjustments of endpoint, sub-trim and digital trim will only
apply to mixed status.
Model Select
EX7 comes with 6 model memory able to
store.
Setting adjustments apply to the current
selected model only, including reset
operation.
Multi-button Function Settings
EX7 allows you to adjust more setting for further usage, which requires multi-button
operations.
Follow below instructions to achieve the function settings.

10
EXMITTER EX6 Digital Radio System
1. Potentiometer Calibration
Holding button K1 & K5 while powering on -- Start "beep-beep-beep" meaning it is
calibrating -- After beeping, holding K2 & K6 to exit calibration -- There will be "beep-
beep" / "beep" based on left throttle mode / right throttle mode.
2. Turbo Switch
Holding OK & K4 & K8 while powering on -- on as 20dbm.
Holding OK & K3 & K7 while powering on -- off as 14dbm.
3. Logo on/off
Holding BACK & UP while powering on -- Display / hide EXMITTER logo.
4. Mode1 / Mode 2 Switch
Holding OK & DOWN & K6 while powering on -- Saved as Mode 2(left throttle).
It comes with "beep--beep" sound when setting as mode 2.
Holding OK & DOWN & K2 while powering on -- Saved as Mode 1(right throttle).
It comes with "beep--" sound when setting as mode 1.
After switch setting of mode 1 / mode 2, you also need to switch the sticks mechanically
following below steps.
Screw #1
Screw #2
Screw #3 Screw #4
Limit Plate
Screw #5
Screw #6
Spring Plate
Screw #7
Screw #8
Inhaltsverzeichnis
Andere EXMITTER Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken

Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung

One Remote
One Remote RMB4 Bedienungsanleitung

FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung












