Extech Instruments EX210 Bedienungsanleitung

User Guide

Multimeter with IR Thermometer

Extech EX210 and EX210T (True RMS)

EX210_EX210T-en-US_v1.5 9/15

Introduction

Thank you for selectin the Extech EX210/EX210T True RMS (EX210T only) Autoran in Multimeter.

This meter measures AC/DC Volta e, AC/DC Current, Resistance, Diode Test, and Continuity plus

non-contact InfraRed Temperature. Proper use and care of this meter will provide many years of

reliable service. Please visit the Extech Instruments website (www.extech.com) to check for the latest

version of this User Guide. Extech Instruments is an ISO-9001 certified company.

Safety

This symbol adjacent to another symbol, terminal or operatin device indicates

that the operator must refer to an explanation in the Operatin Instructions to

avoid personal injury or dama e to the meter.

This WARNING symbol indicates a potentially hazardous situation, which if not

avoided, could result in death or serious injury.

This CAUTION symbol indicates a potentially hazardous situation, which if not

avoided, may result dama e to the product.

This symbol advises the user that the terminal(s) so marked must not be

connected to a circuit point at which the volta e with respect to earth round

exceeds (in this case) 600 VAC or VDC.

This symbol adjacent to one or more terminals identifies them as bein associated

with ran es that may, in normal use, be subjected to particularly hazardous

volta es. For maximum safety, the meter and its test leads should not be handled

when these terminals are ener ized.

This symbol indicates that a device is protected throu hout by double insulation or

reinforced insulation.

PER IEC1010 OVERVOLTAGE INSTALLATION CATEGORY

OVERVOLTAGE CATEGORY I

Equipment of OVERVOLTAGE CATEGORY I is equipment for connection to circuits in which

measures are taken to limit the transient overvolta es to an appropriate low level.

Note – Examples include protected electronic circuits.

OVERVOLTAGE CATEGORY II

Equipment of OVERVOLTAGE CATEGORY II is ener y-consumin equipment to be supplied from

the fixed installation.

Note – Examples include household, office, and laboratory appliances.

OVERVOLTAGE CATEGORY III

Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations.

Note – Examples include switches in the fixed installation and some equipment for industrial use

with permanent connection to the fixed installation.

OVERVOLTAGE CATEGORY IV

Equipment of OVERVOLTAGE CATEGORY IV is for use at the ori in of the installation.

Note – Examples include electricity meters and primary over-current protection equipment

WARNING

CAUTION

MAX

600V

EX210_EX210T-en-US_v1.5 9/15

CAUTIONS

Improper use of this meter c n c use d m ge, shock, injury or de th. Re d nd underst nd

this user m nu l before oper ting the meter.

Alw ys remove the test le ds before repl cing the b ttery or fuses.

Inspect the condition of the test le ds nd the meter itself for ny d m ge before oper ting the

meter.

Use gre t c re when m king me surements if the volt ges re gre ter th n 25 VAC rms or 35

VDC. These volt ges re considered shock h z rd.

W rning! This is Cl ss A device. This device c n c use interference in residenti l re s.

Alw ys disch rge c p citors nd remove power from the device under test before performing

Diode, Resist nce or Continuity tests.

Volt ge checks on electric l outlets c n be difficult nd misle ding bec use of the uncert inty

of connection to the recessed electric l cont cts. Other me ns should be used to ensure th t

the termin ls re not "live".

If the equipment is used in m nner not specified by the m nuf cturer, the protection provided

by the equipment m y be imp ired.

This device must not be used by children. It cont ins h z rdous objects s well s sm ll p rts

th t the children could sw llow.

Do not le ve b tteries nd p cking m teri l lying round un ttended; they c n be d ngerous

to children.

In the event th t this device will be stored for n extended period of time, remove the b tteries.

Expired or d m ged b tteries c n le k nd c n be h z rdous to skin. Use suit ble h nd

gloves in such c ses.

Do not short-circuit the b ttery. Do not pl ce the b ttery ne r fire.

Never mix b ttery types. Alw ys inst ll new b tteries of the s me type.

EX210_EX210T-en-US_v1.5 9/15

SAFETY INSTRUCTIONS

This meter has been designed for safe se, b t m st be operated with ca tion. The r les listed below

m st be caref lly followed for safe operation.

1. NEVER apply voltage or c rrent to the meter that exceeds the specified maxim m:

Input Protection Limits

Function Maximum Input

V AC/DC, Resistance, Diode Test, Contin ity 600 VDC/AC rms

µA or mA AC/DC 200mA f sed

A AC/DC 10A f sed

2. USE EXTREME CAUTION when working with high voltages.

3. O NOT meas re voltage if the voltage on the "COM" inp t jack exceeds 600V above earth

gro nd.

4. NEVER connect the meter leads across a voltage so rce while the f nction switch is in the

c rrent, resistance, or diode mode. Doing so can damage the meter.

5. ALWAYS discharge filter capacitors in power s pplies and disconnect the power when making

resistance or diode tests.

6. ALWAYS t rn off the power and disconnect the test leads before opening the covers to replace

the f se or batteries.

7. NEVER operate the meter nless the back cover and the battery and f se covers are in place

and fastened sec rely.

8. If the eq ipment is sed in a manner not specified by the man fact rer, the protection provided

by the eq ipment may be impaired.

EX210_EX210T-en-US_v1.5 9/15

Controls and Jacks

1. IR Thermometer

2. Laser Pointer

3. 2000 ount LCD

4. MAX button

5. MODE button

6. FUNCTION swit h

7. mA, µA and 10A input ja ks

8. IR Thermometer button

9. HOLD button

10. RANGE button

11. Positive input ja k

12. COM input ja k

Note: Tilt stand, test lead holders, and battery ompartment are on rear of unit.

Symbols and Enunciators

Continuity

Diode test

µ mi ro (10

-6

) (amps)

m milli (10

-3

) (volts, amps)

A Amps

k kilo (10

) (ohms)

M mega (10

) (ohms)

Ohms

V Volts

AC Alternating urrent

DC Dire t urrent

ºF Degrees Fahrenheit

ºC Degrees Centigrade

MAX Maximum

AUTO Autoranging

HOLD Display hold

SCAN IR temperature in progress

EX210_EX210T-en-US_v1.5 9/15

Operating Instructions

WARNING: Risk of electrocution. igh-voltage circuits, both AC and DC, are extremely dangerous

and should be measured with great care.

1. ALWAYS turn the function switch to the OFF position when the meter is not in use.

2. If “OL” appears in the display during a measurement, the value exceeds the range you have

selected. Change to a higher range.

AC/DC VOLTAGE MEASUREMENTS

CAUTION: Do not measure DC voltages if a motor on the circuit is being switched ON or OFF.

Large voltage surges may occur that can damage the meter.

1. Rotate the function switch to the V

or V

position.

2. Insert the black test lead banana plug into the negative COM jack. Insert the red

test lead banana plug into the positive V jack.

3. Touch the black test probe tip to the negative side of the circuit.

Touch the red test probe tip to the positive side of the circuit.

4. Read the voltage in the display.

AC/DC CURRENT MEASUREMENTS

1. Insert the black test lead banana plug into the negative COM jack.

2. Press the MODE button to indicate “DC” or “AC” on the display.

3. For current measurements up to 2000µA, set the function switch to the µA position

and insert the red test lead banana plug into the µA/mA jack.

4. For current measurements up to 200 mA DC, set the function switch to the mA

position and insert the red test lead banana plug into the µA/mA jack.

5. For current measurements up to 10A DC, set the function switch to the 10A position

and insert the red test lead banana plug into the 10A jack.

6. Connect the test leads in series with the circuit under test.

7. Apply power to the circuit.

8. Read the current in the display.

EX210_EX210T-en-US_v1.5 9/15

RESISTANCE MEASUREMENTS

WARNING: To avoid electric shock, disconnect power to the unit under test and discharge all

capacitors before taking any resistance measurements. Remove the batteries and unplug the line

cords.

1. Rotate the function switch to the Ω position.

2. Insert the black test lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive jack.

3. Touch the test probe tips across the device under test.

4. Read the resistance in the display.

CONTINUITY CHECK

WARNING: To avoid electric shock, never measure continuity on circuits or wires that have a

voltage potential.

1. Rotate the function switch to the position.

2. Insert the black lead banana plug into the negative COM jack.

Insert the red test lead banana plug into the positive jack.

3. Press the MODE button to indicate“ " on the display

4. Touch the test probe tips to the circuit or wire you wish to check.

5. If the resistance is less than the continuity threshold, the audible signal will sound.

DIODE TEST

1. Rotate the function switch to the green position.

2. Insert the black test lead banana plug into the negative COM jack and the red test

lead banana plug into the positive jack.

3. Press the MODE button to indicate “ “and “V” on the display.

4. Touch the test probes to the diode under test. Forward voltage will typically indicate

0.400 to 0.700V. Reverse voltage will indicate “OL”. Shorted devices will indicate

near 0V and an open device will indicate “OL” in both polarities.

EX210_EX210T-en-US_v1.5 9/15

NON-CONTACT INFRARED TEMPERATURE MEASUREMENTS

1. Rotate the function switch to the IR position. The uppe ight fou digit tempe atu e display will

switch on.

2. P ess the MODE button to select °F o °C.

3. Aim the inf a ed senso (top of mete ) at the su face to be measu ed.

4. P ess and Hold the IRT button to tu n on the IR the momete and lase pointe . The lase

pointe identifies the su face spot to be measu ed and “SCAN” will flash in the display.

5. Read the tempe atu e in the display.

6. The a ea of the su face to be measu ed must be la ge than the spot size as dete mined by the

distance to spot size values listed in the specification table.

7. Release the IRT button to tu n the IR the momete and lase pointe off. “HOLD” and the

final measu ed value will emain in the display.

WARNING: Do not directly view or direct t e laser pointer at an eye. Low powe visible lase s

do not no mally p esent a haza d, but may p esent some potential fo haza d if viewed di ectly fo

extended pe iods of time.

IR Spot to Distance Diagram

The 4:1 spot to distance atio dete mines the size of the measu ed su face a ea with espect to the

distance the mete is held away f om the su face.

IR Measurement Notes

1. The object unde test should be la ge than the spot (ta get) size calculated by the field of view

diag am.

2. If the su face of the object unde test is cove ed with f ost, oil, g ime, etc., clean befo e taking

measu ements.

3. If an object's su face is highly eflective, apply masking tape o flat black paint to the su face

befo e measu ing.

4. The mete will not make measu ements th ough glass steam, dust, and smoke.

5. To find a hot spot, aim the mete outside the a ea of inte est then scan ac oss (in an up and

down motion) until the hot spot is located.

1”

@ 4”

2”

@ 8”

4”

@ 16”

20mm

@ 80mm 40mm

@ 160mm 80mm

@ 320mm

EX210_EX210T-en-US_v1.5 9/15

AUTORANGING/MANUAL RANGE SELECTION

When the mete is fi st switched on, it automatically ente s the AutoRanging mode. This

automatically selects the best ange fo the measu ements being made and is gene ally the best

mode fo most measu ements. Fo measu ement situations equi ing that a ange be manually

selected, pe fo m the following:

1. P ess the RANGE button. The “AUTO” display indicato will tu n off.

2. P ess the RANGE key to step th ough the available anges until the ange desi ed is selected.

3. P ess and hold the RANGE button fo 2 seconds to exit manual anging.

Note: Manual anging does not apply to the Tempe atu e, Diode and Continuity functions.

MAX (MAXIMUM READING) MODE

1. P ess the MAX button to activate the MAX mode. The display icon "MAX" will appea . The mete

will display and hold the maximum eading and will update only when a new maximum value is

detected.

2. P ess the MAX button again to exit the mode.

Note: Max does not apply to the Resistance, Diode and Continuity functions.

DISPLAY BACKLIGHT

P ess and hold the IRT button fo 2 second to tu n the backlight on. The backlight will

automatically tu n off afte app oximately 10 seconds o p ess and hold the button again fo 2

seconds to manually tu n it off.

HOLD

The HOLD function f eezes the eading in the display. P ess the HOLD button momenta ily to

activate o to exit the HOLD function.

Note: The HOLD button does not function in the IR measu ement mode.

AUTO SLEEP

If no button is p essed the auto sleep featu e will place the mete in sleep mode afte app oximately

15 minutes of ope ation. If this happens, p ess any button to wake the mete o switch the mete to

OFF if it no longe in use.

EX210_EX210T-en-US_v1.5 9/15

Maintenance

WARNING: To avoid elect ic shock, disconnect the test leads f om any sou ce of voltage befo e

emoving the back cove o the batte y o fuse cove s.

WARNING: To avoid elect ic shock, do not ope ate the mete until the batte y and fuse cove s a e

in place and fastened secu ely.

This MultiMete is designed to p ovide yea s of dependable se vice, if the following ca e inst uctions

a e followed:

1. KEEP THE METER DRY. If it gets wet, wipe it off.

2. USE AND STORE THE METER IN NORMAL TEMPERATURES. Tempe atu e ext emes can

sho ten the life of the elect onic pa ts and disto t o melt plastic pa ts.

3. HANDLE THE METER GENTLY AND CAREFULLY. D opping it can damage the elect onic pa ts

o the case.

4. KEEP THE METER CLEAN. Wipe the case occasionally with a damp cloth. DO NOT use

chemicals, cleaning solvents, o dete gents.

5. USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND TYPE. Remove old o

weak batte ies so they do not leak and damage the unit.

6. IF THE METER IS TO BE STORED FOR A LONG PERIOD OF TIME, the batte ies should be

emoved to p event damage to the unit.

BATTERY and FUSE Repla ement

WARNING: To avoid elect ic shock, disconnect the test leads f om any sou ce of voltage befo e

emoving the batte y cove .

1. Tu n powe off and disconnect the test leads f om the mete .

2. Lift the mete stand to expose the batte y cove .

3. Open the ea batte y/fuse compa tment by emoving the Phillips head sc ew on the lowe ea of

the mete .

4. Ca efully pull down on the cove just enough to elease the latch and then lift it off. The cove will

not pull down all the way.

5. Remove the old batte y o fuse and install a new one of the co ect ating.

6. Place the batte y/fuse cove back in place. Secu e with the sc ew.

WARNING: To avoid elect ic shock, do not ope ate the mete until the batte y cove is in place and

fastened secu ely.

NOTE: If the mete does not wo k p ope ly, check the fuses and eplace the batte y to make su e that

they a e still good and that they a e p ope ly inse ted.

Battery Safety Reminders

o Please dispose of batte ies esponsibly; obse ve local, state, and national egulations.

o Neve dispose of batte ies in a fi e; batte ies may explode o leak.

o Neve mix batte y types; install new batte ies of the same type.

Andere Handbücher für EX210

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Extech Instruments Multimeter Handbücher

Extech Instruments

Extech Instruments EX330 Bedienungsanleitung

Extech Instruments

Extech Instruments EX540 Bedienungsanleitung

Extech Instruments

Extech Instruments EX505-K Bedienungsanleitung

Extech Instruments

Extech Instruments 410 Bedienungsanleitung

Extech Instruments

Extech Instruments EX623 Bedienungsanleitung

Extech Instruments

Extech Instruments EX310-NIST Bedienungsanleitung

Extech Instruments

Extech Instruments MA200 Bedienungsanleitung

Extech Instruments

Extech Instruments EX430A Bedienungsanleitung

Extech Instruments

Extech Instruments RHT50 Bedienungsanleitung

Extech Instruments

Extech Instruments EX410 Bedienungsanleitung

Extech Instruments

Extech Instruments EX205T Bedienungsanleitung

Extech Instruments

Extech Instruments 412355A Oyster Series Bedienungsanleitung

Extech Instruments

Extech Instruments 407735 Bedienungsanleitung

Extech Instruments

Extech Instruments EX430A Bedienungsanleitung

Extech Instruments

Extech Instruments RC200 Bedienungsanleitung

Extech Instruments

Extech Instruments EX420A Bedienungsanleitung

Extech Instruments

Extech Instruments EX310 Bedienungsanleitung

Extech Instruments

Extech Instruments MN30 Bedienungsanleitung

Extech Instruments

Extech Instruments EX310 Bedienungsanleitung

Extech Instruments

Extech Instruments 407303 Bedienungsanleitung

Extech Instruments

Extech Instruments EX411A Bedienungsanleitung

Extech Instruments

Extech Instruments 382075 Bedienungsanleitung

Extech Instruments

Extech Instruments 401025 Bedienungsanleitung

Extech Instruments

Extech Instruments 407910 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung