Extractor Corporation SUITMATE Bedienungsanleitung

115 V, 60 Hz, 8.6 A SUITMATE®Unit

TROUBLESHOOTING GUIDE

115 V, 60 Hz, 8.6 A SUITMATE® Unit

If you are experiencing diculty with your SUITMATE®unit, please read through the following pages

to see if the problem you are experiencing is described. If so, please follow the troubleshooting

steps to attempt to x the problem. If further assistance is required, please contact the factory for

further recommendations at:

(Toll Free) 800-553-3353, (Telephone) 847-742-3532, or (E-mail) info@suitmate.com.

Problem: The unit is not working. There is no sound, no hum, and no noise at all when the lid

is depressed.

• Is there power to the unit? An A.C. voltmeter set to the appropriate range can be used to check

for power by measuring across the “LINE” side of the GFCI. The GFCI can be accessed from the

bottom of the unit.

• If there is no power, check the wire connections to the GFCI and check the power at the

main circuit breaker

• If there is power to the unit, check to see if the GFCI is tripped o. Attempt to reset the

GFCI by pressing the “TEST” button followed by the “RESET” button.

• If the GFCI cannot be reset, it may be faulty and in need of replacement.

• If the GFCI resets and the unit still is not working, please proceed to the next

troubleshooting steps.

• Can you hear the Micro Switch engaging (indicated by a faint clicking sound)? If not, the Micro

Switch may be out of alignment and require adjustment. The Micro Switch is located on the

backside of the unit. In order to access it, the unit will need to be removed from the wall.

• On the backside of the unit, there is a stainless steel box. Remove the box cover. The Micro

Switch is located on the right hand side of this box and has a small wire cable attached to

a copper arm. Check if the Micro Switch is engaging properly by depressing the Lid while

still maintaining visual contact with the Micro Switch.

• Does the wire cable pull up on the arm of the Micro Switch? If the arm is moving but

does not make an audible “click,” the Micro Switch needs to be adjusted. Please refer

to our website www.suitmate.com under RESOURCES for further instruction.

• Does the wire cable not move at all? This could indicate a broken Actuator Screw.

Please refer to our website www.suitmate.com under RESOURCES for further

instruction.

• Is there power after the Timer? With the Lid depressed, use an A.C. voltmeter set to the

appropriate range to check for power at the #4 (or COM) connection on the Timer.

• If there is no power at that connection point, the Timer may be faulty and in need of

replacement.

• If the Timer is functioning properly, the power reading at the #4 (or COM) connection will

last for approximately 7-8 seconds and then shut o.

Problem: The unit is humming when the Lid is depressed, but the Basket is not spinning.

• Does the Basket spin freely? With the Lid in the open and upright position, use a piece of bar

stock or a wood 5 cm x 10.2 cm (2 in x 4 in) to manually depress the two Brake Rods that come

up through the Top on each side of the opening for the Basket. Simultaneously depress both

Brake Rods approximately 1.3 cm (1/2 in) and attempt to spin the Basket. With the Brake Rods

depressed, it should take very minimal force to spin the Basket.

CAUTION!

Make certain the main electrical power to the unit is turned o – and locked

out – before beginning work on the SUITMATE®unit.

115 V, 60 Hz, 8.6 A SUITMATE®Unit

• If the Basket spins freely, the problem may be due to a loose wire or a broken motor

component. Remove the end cap from the bottom of the motor to visually inspect the

motor components for cracks, frayed wires and broken wires. If anything is found to be

broken, contact Extractor Corporation for additional assistance or replacement parts.

• If the Basket does not spin freely or at all, the problem may be due to an obstruction within

the unit or faulty motor bearings. Check for signs of an obstruction within the unit by gently

pulling the Basket aside and, with a ashlight, look down inside the unit for something

wrapped around the Basket or Brake Disc (located around the bottom of the Basket). If

foreign objects are found, try to pull them out with a long hook or other instrument. If

the obstruction cannot be removed in this manner, the Top and Sub-Top may need to be

removed to fully access the inside of the unit. Please refer to our website

www.suitmate.com under RESOURCES for further instruction.

• If no signs of an obstruction can be seen, the issue may be faulty motor bearings.

Please contact Extractor Corporation for additional troubleshooting regarding this issue.

Problem: The unit is humming as soon as power is engaged and before the Lid is depressed.

This could be caused by either a faulty timer or an over-adjustment on the Micro Switch.

• To test for a faulty timer in this instance, place the Lid in the open and upright position and use

an A.C. voltmeter set to the appropriate range to check for power at the #4 (or COM) connection

on the Timer.

• If there is power at the #4 (or COM) connection on the Timer with the Lid in the upright

position, the Timer is faulty and should be replaced.

• To check the adjustment on the Micro Switch, please refer to our website www.suitmate.com

under RESOURCES.

Problem: The unit is leaking.

The SUITMATE®unit does not have any seals or gaskets that can wear or break down. Leaking

is primarily caused by an obstruction within the interior drain channel, drain hose, or P-trap (if

applicable). The interior drain channel is a 5 cm (2 in) U channel that runs around the perimeter

of the interior of the unit. Check for an obstruction by gently pulling the Basket aside and, with a

ashlight, look down inside the unit for something blocking the drain channel or drain opening.

If foreign objects are found, try to pull them out with a long hook or other instrument. If the

obstruction cannot be removed in this manner, the Top and Sub-Top may need to be removed

to fully access the inside of the unit. Please refer to our website www.suitmate.com under

RESOURCES for further instruction.

Problem: The GFCI is tripping o every time the unit is run.

• The SUITMATE® unit should be connected to a 115 V, 60 Hz, 20 A dedicated circuit. If the unit

is connected on a circuit with other items or appliances, it is possible that the initial draw of

the unit could be overloading the circuit causing the GFCI to trip o. If the SUITMATE® unit is

not on a dedicated circuit, switch it to a 115 V, 60 Hz, 20 A dedicated circuit and verify that the

problem is resolved.

• If the SUITMATE® unit is already on a 115 V, 60 Hz, 20 A dedicated circuit, the GFCI may be

faulty, have a loose connection, or there may be a short within the unit.

• Verify that all wires are securely connected on both the “LINE” and “LOAD” sides of the

GFCI. If a loose connection is found, correct it, restore power and verify that the problem is

resolved.

CAUTION!

Make certain the main electrical power to the unit is turned o – and locked

out – before beginning work on the SUITMATE®unit.

115 V, 60 Hz, 8.6 A SUITMATE®Unit

• If a loose connection is not found or the GFCI still trips o, turn o the main electrical power

to the unit and bypass the GFCI. Connect the unit direct to a ground wall circuit and see if the

main circuit breaker trips o. If the main circuit breaker does not trip, the GFCI is most likely

faulty and should be replaced. If the main circuit breaker does trip, there is probably a short

within the unit. Please call Extractor Corporation for additional troubleshooting assistance.

Problem: The GFCI is tripping o at random times, no specic pattern or reason.

• The SUITMATE® unit should be connected to a 115 V, 60 Hz, 20 A dedicated circuit. If the unit

is connected on a circuit with other items or appliances, it is possible that at the random time

when the unit is running at the same time as another appliance on the circuit, the circuit could

become overloaded and cause the GFCI to trip o. If the SUITMATE® unit is not on a dedicated

circuit, switch it to a 115 V, 60 Hz, 20 A dedicated circuit and verify that the problem is resolved.

• If the SUITMATE® unit is already on a 115 V, 60 Hz, 20 A dedicated circuit, the GFCI may be faulty

or have a loose connection.

• Verify that all wires are securely connected on both the “LINE” and “LOAD” sides of the

GFCI. If a loose connection is found, correct it, restore power and verify that the problem is

resolved.

Problem: The Basket takes longer than 1 second to stop when you lift the Lid.

There is a problem with the Brakes. Please take the unit out of service immediately and contact

Extractor Corporation.

Problem: The unit will run but takes a long time to reset before being able to run again.

This may indicate a faulty Timer, a faulty Motor Thermal Breaker, or an obstruction within the unit.

• To test for a faulty Timer, please refer to our website www.suitmate.com under RESOURCES for

instructions on bypassing the timer. If the unit functions normally once the timer is bypassed,

the timer should be replaced.

• If the unit takes more than 5 minutes to reset, there may be either an obstruction within the

unit that is causing friction while the unit is running or a faulty Thermal Breaker.

• Check for signs of an obstruction within the unit by gently pulling the Basket aside and,

with a ashlight, look down inside the unit for something wrapped around the Basket or the

Brake Disc (located around the bottom of the Basket). If foreign objects are found, try to

pull them out with a long hook or other instrument. If the obstruction cannot be removed

in this manner, the Top and Sub-Top may need to be removed to fully access the inside

of the unit. Please refer to our website www.suitmate.com under RESOURCES for further

instruction on removing these pieces.

• If no signs of an obstruction are visible, the issue could be a faulty Motor Thermal Breaker.

Please contact Extractor Corporation for additional troubleshooting regarding this issue.

Problem: The unit is making excessive noise when it is running.

• The patrons may not be operating the unit correctly. Test this by putting a swimsuit in the

Basket and pushing it all the way down, making sure that it is evenly distributed in the bottom

of the unit. Operate the unit.

• If the unit is still noisy under correct operation, attempt to run it empty. If the noise

remains even with the unit being empty, it could indicate faulty motor bearings or worn out

brakes. Please contact Extractor Corporation for additional information.

Note

If the above steps and suggestions have not resolved your problem, please contact Extractor

Corporation at:(Toll Free) 800-553-3353, (Telephone) 847-742-3532, or (E-mail) info@suitmate.com.

CAUTION!

Make certain the main electrical power to the unit is turned o – and locked

out – before beginning work on the SUITMATE®unit.

Andere Handbücher für SUITMATE

Inhaltsverzeichnis

Andere Extractor Corporation Schrubber Handbücher

Extractor Corporation

Extractor Corporation SUITMATE Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

FIORENTINI

FIORENTINI ET 65-75 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung